Replacement 4-Way Recommendation for Bully Black Bull LED Step part # BBS-1104L

Question

Question:

I have a Hitch Mounted Step Bully with seven LEDs in it. Someone managed to rip out my wiring harness. Is it possible to rewire with a new wire harness? If so,how much will be a new harness? Thank you.

asked by: Theo R

0

Expert Reply:

If you still have access to the four wires that run to the back of the Bully Black Bull LED Step part # BBS-1104L you can replace the 4-way with a # 18004. If you do not have access to the wiring we do not have a solution for you.

expert reply by: Jameson C

0

Answer 1

The harness part #CR-600L-LED that you referenced is a replacement for the Round Tube Stainless Steel Trailer Hitch Receiver Step with LED Lights #CR-600LED which uses a standard 4-way connection which should be present on your 2017 Chevy Silverado.…

view full answer...

Answer 2

Yes, the Pilot Replacement LED Strip #CR-600L-LED is the correct item to replace the LED lights on your Bully Black Bull LED Round Tube Hitch-Mounted Step #BBS-1104L. The kit includes the LEDs, wiring and adhesive strip.

view full answer...

Answer 3

To replace your wiring on your Bully hitch step #CR-600LED I recommend the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector #HM38138 along with heat shrink connectors #DW05743-5. For added protection you can add a wire loom like #7509-1 sold…

view full answer...

Answer 4

For a replacement LED light for the Bully Round Tube Stainless Steel Trailer Hitch Receiver Step, #CR-600LED, you will want the Replacement LED Light, #CR-600L-LED.

view full answer...

Answer 5

It sounds like you have the Bully Tube Stainless Steel Trailer Hitch Receiver Step #CR-600LED and are looking for a replacement light strip for it. If so, the correct part number would be part #CR-600L-LED.

view full answer...

Answer 6

We have the Masterlock hitch lock part #1480DAT which is stainless steel that I would highly recommend. I attached a review video for you to check out as well. The replacement LED strip you need is the part #CR-600L-LED for your #CR-600LED.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

I added a photo which shows the location of the heating element of the Atwood Water Heater GC6AA-10E for you. It is item number 17 in the diagram. Atwood does recommend having a professional do the job if you are replacing it due to its location.

view full answer...

Answer 12

For your Atwood water heater number gc6aa-10e, it sounds like you have either a wiring issue or an element issue. To determine if a replacement is needed you will want to make sure the connections are good to and from your switch. I recommend using a…

view full answer...

Replacement 4-Way Recommendation for Bully Black Bull LED Step part # BBS-1104L

Product Page this Question was Asked From

Continue Researching