Replacement LED Light Strip for Bully Black Bull LED Hitch-Mounted Step BBS-1104L

Question

Question:

Does the CR-600L-LED fit my BBS-1104L 2 inch bar? SPL8003E is on my bar.

asked by: Francis D

0

Expert Reply:

Yes, the Pilot Replacement LED Strip # CR-600L-LED is the correct item to replace the LED lights on your Bully Black Bull LED Round Tube Hitch-Mounted Step # BBS-1104L. The kit includes the LEDs, wiring and adhesive strip.

expert reply by: Adam R

0

Answer 1

The harness part #CR-600L-LED that you referenced is a replacement for the Round Tube Stainless Steel Trailer Hitch Receiver Step with LED Lights #CR-600LED which uses a standard 4-way connection which should be present on your 2017 Chevy…

view full answer...

Answer 2

We have the Masterlock hitch lock part #1480DAT which is stainless steel that I would highly recommend. I attached a review video for you to check out as well. The replacement LED strip you need is the part #CR-600L-LED for your #CR-600LED.

view full answer...

Answer 3

It sounds like you have the Bully Tube Stainless Steel Trailer Hitch Receiver Step #CR-600LED and are looking for a replacement light strip for it. If so, the correct part number would be part #CR-600L-LED.

view full answer...

Answer 4

For a replacement LED light for the Bully Round Tube Stainless Steel Trailer Hitch Receiver Step, #CR-600LED, you will want the Replacement LED Light, #CR-600L-LED.

view full answer...

Answer 5

If you still have access to the four wires that run to the back of the Bully Black Bull LED Step part #BBS-1104L you can replace the 4-way with a #18004. If you do not have access to the wiring we do not have a solution for you.

view full answer...

Answer 6

To replace your wiring on your Bully hitch step #CR-600LED I recommend the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector #HM38138 along with heat shrink connectors #DW05743-5. For added protection you can add a wire loom like #7509-1…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Replacement LED Light Strip for Bully Black Bull LED Hitch-Mounted Step BBS-1104L

Continue Researching