Ground Clearance of Draw-Tite # 76021 Class III Trailer Hitch When Installed on 2015 Jeep Renegade
Question:
Whats the ground clearance after the hitch is installed?
asked by: Adam
Expert Reply:
I can't provide an exact figure as we haven't yet had the opportunity to install the hitch. However, when installed the top of the receiver tube is directly under the bumper fascia. If you measure downward from the bumper fascia about 2-3/4 inches, you'll be right where the bottom of the receiver tube will be.
In other words, measure down from the underside of the bumper fascia at the rear of the vehicle until you hit the ground. Subtract 2-3/4 inches from this figure, and you'll have a rough idea of how much ground clearance will be available under the hitch.
If you'll be using the Renegade for towing, you'll need the following to complete your towing system:
Trailer wiring harness with 4-pole trailer connector, part # 118651
Ball mount, # C45010
1-7/8 inch trailer ball # 19260
2 inch trailer ball # 63845
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: What is Max Safe Tire Temperature
- Q&A: What Size Battery Is Needed for the Lippert 6-Point Ground Control
- Q&A: TrailAir Pin Box LC158778 Installation Instructions
- Q&A: Bolts and Bracket for the Tie Down Caliper to Kodiak Caliper
- Q&A: How to Charge a Trailer Battery Through a 7-Way Connector
- Q&A: Recommended Replacement Hub Assemblies for a Trailex Trailer with a 8 inch Wheel with 4 Bolts
- Q&A: Can I Charge My Trailer Battery Using 7-Way Trailer Connector on Truck
- Article: How to Choose the Right Trailer Hitch Class
- Article: My Trailer Hitch Doesn't Fit
- Article: Most Popular Wheel Bearings
- Article: Trailer Tire Sizing
- Article: Performance Chips and Modules
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Article: How Long Can You Boondock in an RV?