Replacement Hydraulic Brake Assemblies and Drums with 008-201-09 Casting Number for Boat Trailer

Question

Question:

Escort Trailer, surge brakes, year unknown, maybe 90 as boat is a 90. Took of passenger side tire and brake drum. Drum says maximum 12.09 for turning. Tag on outside on drum says: 008-201-09 under that #15425 cup back show appears to be14, frt. appears 11 1/4, 2inch wide So what do I need for R and L backing plates complete. 5 bolt, 2 on each side, 1 on top thx.

asked by: Ron D

0

Expert Reply:

The 008-201-09 number you provided comes back on a Dexter Axle hub that we offer as part # 8-201-9UC3-EZ, a 12 x 2 inch brake drum.

This hub uses a 25580 inner and 15123 outer bearing, so please check the reference numbers on your existing bearings to confirm that this hub is compatible. These hubs use a grease seal with a 2-1/8 inch inner diameter. Since it's kind of difficult to measure the inner diameter of a used grease seal, measure the OD of the spindle where the grease seal rides. You'll want to use a highly accurate measuring device like a digital caliper.

For brake assemblies, I'd recommend Titan's # T4489500 for the right side and # T4489600 for the left. The brake assembly is Galphorite coated to combat corrosion in marine environments. The brake assemblies are compatible with the 5-bolt mounting flange you described. Mounting hardware for the brake assemblies is sold separately. The bolts are part # 7-5, nuts are # 38N and the split lock washers are # 38LW. You'll need 5 of each for each brake assembly.

expert reply by: Mike L

0

Answer 1

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb…

view full answer...

Answer 2

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 3

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Replacement Hydraulic Brake Assemblies and Drums with 008-201-09 Casting Number for Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching