Recommended Weight Distribution Hitch for a 4,000 Pound Trailer and a 2003 Honda Pilot

Question

Question:

I have a 2003 Honda Pilot and tow a travel trailer weighing dry at 3,000 pounds with a tongue weight of 393 pounds. Seeking weight distribution hitch that will provide even towing line and better sway control. What WDH do you recommend? Loaded trailer weight 3,750 to 4,000 pounds. Loaded tongue weight, 400 to 425 pounds.

asked by: Dan

0

Expert Reply:

To be on the safe side, we will assume the maximums; trailer weight of 4,000 pounds and tongue weight of 425 pounds. When selecting a weight distribution system, the most important thing is properly matching tongue weights. That being said, you never want to exceed the gross trailer weight capacity either.

We have a few weight distribution systems with sway control, that have a 400-600 pound tongue weight range and they all have more than enough gross trailer weight capacity. Being that your tongue weight hovers right in the center of this range, 400-425, these systems would be a great fit.

First up, the Reese High Performance Weight distribution system, # RP66558. This system has a 6,000 pound gross trailer weight capacity, more than enough for your setup. And it has a 400-600 pound tongue weight range, good for your 400-425 pound tongue weight. This kit uses a friction sway control system, similar material to brake pads, to reduce sway and help get the trailer back in line when it does start to sway.

The next system is the Reese Strait-Line, part # RP66072. It has a slightly larger GTW, 12,000 pounds and has the same 200-600 pound tongue weight range. The big difference from this system when compared to the other is that it uses a Dual-Cam Sway Control system versus the friction style. The Dual-Cam system is much better sway control system because it is pro-active. It actually works to prevent sway before it even starts as the system actually forces the trailer to stay in a straight line behind the truck. Again, this system does not include the shank, so you will need to purchase it separately.

If you choose one of the kits without a shank, you could use either the Convert-a-Ball Cushioned Shank, part # AMAC1, or the Draw-Tite WD Shank, part # RP54970. Both have plenty of capacity for your needs and should provide adequate adjustment.

I have added links to the parts and the instructions for the WD systems below.

expert reply by: Patrick B

0

Answer 1

If the rear end of your vehicle sags significantly when the trailer is hooked up then you could have an unsafe condition and your front end and tires will not wear properly. The weight is taken off of the front wheels of the vehicle and can cause…

view full answer...

Answer 2

According to Mighty Cord, the #A10-1530DBK power cord adapter will work just fine for you, and would be compatible with the NEMA 5-20R outlet.

view full answer...

Answer 3

I do have an option for you but all of our power inlets are 30 or 50 amps as that is what you will find at an RV park. That said, you can use an adapter if you need to hook up to a 15 or 20 amp outlet. For a 30 amp RV inlet I recommend Mighty Cord…

view full answer...

Answer 4

The Optronics LED Step Light #ILL86BCB that you mention does not have a sensor that operates the light, this light is powered by 12V and has constant power to the unit. Additionally, this light measures 4" tall x 2-1/2" wide x 1-5/16"…

view full answer...

Answer 5

Any time you are towing a trailer that has a fully loaded weigh that is over 50 percent of the vehicle's gross weight, a weight distribution system is recommended. If your vehicle weighs less than 6,000 lbs, a weight distribution system and…

view full answer...

Answer 6

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…

view full answer...

Answer 7

A trailer with a 5000 lb GTW (gross trailer weight) could potentially have a tongue weight 10-15% of its GTW which would be 500-750 lbs. The Curt TruTrack #C17499 Weight Distribution system can handle tongue weights ranging from 500-800 lbs, so…

view full answer...

Answer 8

The 2016 Forest River R-Pod 176 will use an 8 foot awning from the factory. We don't carry an 8 foot option, so I recommend measuring to see if a 10 foot option will work on your trailer. If so, I recommend the Solera 10' White Fade RV Awning…

view full answer...

Answer 9

I do have a possible solution for you but the most well equipped 2018 Jeep Wrangler JL Unlimited has a maximum tongue weight capacity of 350 lbs therefore, the Draw-Tite Max-Frame Trailer Hitch Receiver part #DT78MR will not increase your tongue…

view full answer...

Answer 10

Anytime the fully loaded and ready to tow trailer weight is greater than 50 percent of the weight of the tow vehicle, using weight distribution should be considered. When you get the pop-up, hitch it to the vehicle and pay special attention to the…

view full answer...

Answer 11

I have two excellent options for you to help keep control of the trailer at highway speed, a friction sway control bar like the Reese Friction Sway Control Kit part #83660 with the Sway-Control Bracket part #RP26003 or an electric sway control device…

view full answer...

Answer 12

If you are talking about a pole tongue trailer then there are adapters available, item #RP3280 and item #RP58393, that you can use to connect to the frame and then attach the brackets. The RP3280 will not work with the Reese SC Weight Distribution…

view full answer...

Recommended Weight Distribution Hitch for a 4,000 Pound Trailer and a 2003 Honda Pilot

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching