The correct replacement tarp for your 2008 Ford F-250 short bed with a Truxedo Lo Pro tonneau is the part # TX569101-CVR since the cover you have would be the # TX569101. view full answer...
Individual parts from the Westin Installation Hardware Kit # 23-110PK referenced in your question are unfortunately not available from the manufacturer by themselves. If you need only one or a few of the included parts then you will need to obtain the entire kit.
This will at least give you spare parts for your Nerf Bars if anything else were to need replacement further down the line. This particular kit is designed to replace the mounting hardware for the Westin E-Series Round Nerf Bars... view full answer...
The Wesbar Mini Clearance and Side Marker Trailer Light part # 203233 is a submersible light therefore, the bulb cannot be replaced without braking the seal. If you don't mind breaking the seal to change out the bulb then you can do so with a 193 bulb but otherwise you would need to replace the entire light if the bulb goes out. view full answer...
To replace the Velcro strips for the TruXedo Lo Pro Tonneau Cover # TX577601 on your 2008 Ford F-150 you just need the part # TX1115174. Just keep in mind that you will need to cut the strip down to size as it's technically made for the 6-1/2 foot bed. TruXedo does not offer a replacement Velcro kit specific to 5-1/2 foot beds so this is what you need.
The kit includes 2 Velcro Brand fasteners. I have attached a short video review that you can check out as well. view full answer...
You can still see well enough through the Aries Switchback Headache Rack # AA1110109 that it would not cause visibility issues when looking through the rear view mirror. The holes are big enough you can see anything you'd need to see through the back windshield. view full answer...
My research indicates that grease seal part 125255UC has an outer diameter of 1.980-inches and this correlates with the hubs that use bearing # L44649. The seal part most often used with inner/outer bearing L44649 is seal part # 10-9 which has an inner diameter of 1.50-inches and an outer diameter of 1.987-inches so bearing kit # BK1-150 that you referenced should do it.
You can confirm the seal size by measuring a spindle at the point where the seal rides (point B in the linked image)... view full answer...
To get the replacement hardware for a Curt # 13355 hitch, you'll need the # RHK replacement hardware kit. Us the provided link, when you reach the product page, type '13355' into the provided field and choose 'Curt' from the drop down menu. view full answer...
Yakima refers to the part you're needing as a clip spacer for their 1A RainGutter Towers, part # Y00101.
The replacement plastic clip spacers aren't available individually, they are included in the # Y8810136 replacement hardware bag, so potentially you could need both the # Y8810136 parts bag as well as the # Y8810008 replacement boots. This being said-as outlined in step 10 of the linked instructions you will not need the clip spacers if the backs of the roof rack feet do NOT touch the... view full answer...
I reached out to Dexter and they no longer make that axle. I can confirm based on the bearing sizes you gave that you have a 3,500 lb capacity. If you determine you just want to replace the hub, I recommend the Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 # 84546UC3 or # AKHD-545-35-EZ-K if you have the grease zerk integrated in the spindle.
Since we can't match the spring seat to spring seat dimensions if you want to replace your axle I recommend using... view full answer...
It sounds like you are looking for the wiring harness portion of the Hopkins Endurance Multi-Tow 4-Way Flat to 7-Way RV Trailer Adapter part # HM47180. If that is the case then this part is not available separately but you can obtain something similar with the Pollak Wiring Harness Extension part # PK11-934 and the Quick Fix 4 Pole Flat Trailer End part # HMC20031. If you need butt connectors to finish up your connections you can use part # DW05745-5. view full answer...
We do have mounting hardware available for the Erickson Removable Motorcycle Wheel Chock - 6" Wide Tires # EM07506. What you are looking for is the Replacement Mounting Plates for Erickson Removable Motorcycle Wheel Chock # EM56ZV. You would just need to pick up some 1/4" bolts similar to the ones that come with the original kit to finish the installation. view full answer...
The manual override lever on your brake controller is not available as a replacement part. As much as I hate to say it the best solution is to replace your brake controller. I have included a link below to our complete selection of brake controllers. Its hard to beat the P2 # 90885 but if you want something similar that costs a little less I recommend the Primus # TK90160 which has the same innards as the original Prodigy brake controller. view full answer...
If you have the newer Extang Trifecta 2.0 Soft Tonneau Cover part # EX92405 with the redesigned frame, hinges, and corners, then the Replacement Tarp for Extang Trifecta 2.0 Soft Tonneau Cover part # EX92405-20 is the one for you. view full answer...
If your original light is 4" L x 2" W x 1-1/8" D then Optronics light # MC32AB will fit in its place. If you have different dimensions let me know what they are and I can see if we have anything that is a match. view full answer...
Yes. You can purchase the hardware using part # RHK. You simply enter the manufacturer and the hitch part number and we will ship the hardware kit that comes with that hitch receiver.
The 2014 Ford Escape Class II hitch receiver options:
Curt # C12111
Draw-Tite # 36524
Draw-Tite # 36529 view full answer...
We do have a selection of bunk boards available which you can use for a variety of lengths. Below are the different lengths we carry:
2' - # CE27850
3' - # CE27800
4' - # CE27810
5' - # CE27820
6' - # CE27840
7' - # CE27845
Since bunk board brackets can sit at different locations along the boat frame you'll just need to compare the different lengths to what you currently have and you'll be good to go! view full answer...
We did get one photo which I've attached. The replacement head you are seeking for your # RP66084 system is the Replacement Head for Reese Weight Distribution System - Trunnion Bar # RP58167. I've attached a video of this product to assist. view full answer...
For a replacement 7-way and 4-Pole Trailer Connector Socket w/ Mounting Bracket you would will need the part # HM40975. The 4' Pigtail mating connector and wiring harness # PK11998 serve as a bridge between your vehicle wiring and a 7-pole trailer connector. This harness will splice into your factory tow package. I have a linked video that shows at the 0:47 mark how to splice and connect the new harness. view full answer...
It sounds like you are going to need either the Replacement Motor for Kwikee Electric RV Steps part # LC379147 or the Replacement Gear Box and A Linkage part # LC379160. I spoke with Lippert and was able to cross reference the info provided so I can confirm these are the correct parts. In order to determine which exact component is creating the noise, I recommend isolating each (unhooking shaft from motor and applying power etc). as that would then give you your answer.
Please note, depending... view full answer...
The correct Base Rails for Thule TracRac SR or G2 Sliding Truck Bed Ladder Racks for a 2018 Ford F-150 with 6-1/2' bed is part # TH21501. This would then give you the Thule TracRac SR Sliding Truck Bed Ladder Rack part # TH43002XT-501. view full answer...