Yes, whoever it is that told you about the Redarc Tow-Pro Elite Trailer Brake Controller, # RED44FR has definitely made a great recommendation to you, absolutely this will work in your 2022 Subaru Ascent. The installation process depends if your Ascent is equipped with the factory tow package.
If your Ascent has the factory tow package you will be able to use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers, # 3062-P. This plugs into the factory trailer brake controller... view full answer...
First off, congratulations on your new vehicle!
Now, to answer your questions:
One of the great features of this controller is that it will automatically adjust your trailer's braking based on deceleration of your Ascent. Once installed, you do not need to adjust the settings on the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 as long as you leave it plugged in. If you unplug the controller, you'll need to go through the initial set-up once again because it assumes the controller... view full answer...
The lid of the Carpod Walled Cargo Carrier w/ Lid # M2205-2201 will actually need to be completely removed when you are completely folding it up. You will want to put the lid elsewhere, like inside your vehicle, if you do not need to use the carrier but still have it in the hitch.
To mount it to your hitch you can use Pin and Clip # PC3 though I recommend using the Trailer Hitch Receiver Lock # e98880 to lock the Carpod to your and protect your investments.
Additionally, if you decide... view full answer...
The best size for a cargo box for a vehicle normally is the biggest size that allows the rear hatch to open with the box installed. So to determine which size(s) would allow the rear hatch of your 2020 Subaru Ascent to open you'd need to measure from the center of the front bar back to the rear hatch seam on the vehicle. If the measurement is 55 inches or over the 22 cubic foot Thule Motion XT part # TH629906 would fit whereas the # TH629806 only requires 51-1/4 inches.
There's also the... view full answer...
The Thule Mountaineer uses narrower U-bolts so for a roof rack that's compatible with that box and the roof of your 2019 Subaru Ascent with factory roof rails the Thule Square Bar Roof Rack part numbers # TH712400 and # TH450R would be what you'd need! view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver part # 76253 and the OEM Subaru Trailer Hitch Receiver L101SXC002 actually install using most of the same holes on the vehicle. I looked through the instructions you were referencing to confirm this. The OEM option is a three piece hitch which is why it looks like it installs differently but I can promise you that it replaces the bumper beam just like the Draw-Tite option, it's just rather hard to tell from the instructions.
There will be... view full answer...
The Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR can definitely be installed on your 2021 Subaru Ascent, but how it hooks up to your vehicle will depend on how it came wired from the manufacturer.
If you have the factory tow package, the install will be quick and easy. The Tekonsha Harness # 3062-P will allow you to plug directly into a port under the dash, and the # 331-TPH-017 will then adapt that harness to attach directly to the # RED44FR controller. There is not currently... view full answer...
The connector you are looking for to install the Curt trailer wiring kit part # C56040 on your 2019 Subaru Ascent is located behind the driver side rear panel in the cargo area. If you check out the picture I attached you'll see where to find it. view full answer...
The photo you sent looks like it may be what you need to hardwire to the Tekonsha Primus IQ Trailer Brake Controller # TK90160 to as a step of the installation.
To install this brake controller in your 2019 Subaru Ascent without the factory tow package you need to start by adding a 4-way, the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118790; I have added a link to an installation video of this connector on a '19 Ascent for you to take a look at.
You will also need... view full answer...
The Redarc Tow Pro Elite part # RED63RR will install very easily on your 2023 Subaru Ascent with the factory tow package using the install harness part # 3062-P which plugs into a port under the dash of your vehicle. It's very easy to do for sure. view full answer...
As the Coil SumoSprings # CSS-1094R will fit in between the slats of the coil spring on your 2020 Subaru Ascent, it will not lift the rear up at all. However, they will definitely help if the back of your vehicle is sagging as they will supplement your factory springs and give them a little support when needed. view full answer...
You are right to be concerned with the integrity of the vehicle's frame when it comes to towing and tongue weight capacities. The towing and tongue weight capacities of a hitch are just what that specific hitch is rated for and does not transfer over to what the vehicle can handle. Subaru lists two different Gross Towing Weight (GTW) and Tongue Weight (TW) capacities based on the model of the Ascent.
Models with air-cooled continuously variable transmission fluid cooler*1: 5,000lbs (2,268... view full answer...
Basically all of the instructions for trailer wiring like the Tekonsha # 118290 for your 2020 Subaru Ascent are kind of vague when it comes to routing the power wire to the battery which is why we came up with a helpful article on this (see attached).
Although it seems like a pain, the easiest way to route the wire is by going under the vehicle. If there are any places where you can run the wire through the frame of your vehicle then do that as it will be the easiest way to avoid damage... view full answer...
Due to the thinner gauge wiring of the # 118290 for the 12 volt accessory circuit you'd be limited to the 20 amp charger for your battery. view full answer...
I did some research and did find a way to turn it off, but there is not a way to calibrate the system to recognize "common" items and this will need to be done every time the vehicle is restarted.
With that said, what you need to do is when you put the vehicle in reverse, the camera will appear on your dash monitor. In the lower right hand corner of said monitor, you will see a green P with several curved lines radiating out from it and ON directly underneath it. All you need to do is... view full answer...
The 12V power to your 7-way and brake controller should be separate so it wouldn't impact the power to # RED44FR. It sounds like you have the tow package so the # RED63RR will be a better option. This comes with an adapter that will allow you to use the # 3062-P wiring harness for a plug and play installation. view full answer...
The heat shield on your 2020 Subaru Ascent should have been trimmed so that it doesn't rub against the Curt Trailer Hitch Receiver # C13400 and make noise. It sounds to me like your installer was just too lazy to do the job properly. I would take it back and have them trim it around the hitch or you can do it yourself if you don't trust them to do a good job. view full answer...
The location to plug the Tekonsha Plug-In Wiring Adapter part # 3062-P is just above the driver's side kick panel just behind the hood release latch mounting block. It will be wrapped in black (most often) tape to keep it clean and free of debris. It will be taped up to another main harness and this is likely causing your issue. Please see the attached photo for the exact location. view full answer...
Yes the upright mast of the Swagman Current Bike Rack for 2 Electric Bikes - 1-1/4 and 2 Hitches - Frame Mount # S64678 that you referenced does fold down so it can store in a smaller area. Check out the picture I attached as well as the review video for more info. view full answer...