Good question and the 2,000 lb working load limit (WLL) of the Erickson Horizontal E-Track such as the 5 foot # E19148 is the safe limit for the weight of the cargo the track is helping secure. To simplify, it is the cargo capacity that the track can safely handle so you do not want to exceed it. However, the 2,000 lb limit is per track, so that means if you put down two tracks horizontally, your WLL would go up to 4,000 lbs.
This track cannot actually be welded on, it needs to be secured... view full answer...
I went out into our showroom and measured a Stay-Put Cradle, part # 853-7887, that was on one of our floor model Thule Roadway 2 Bike Carrier, part # TH912XT and found out that the hole is 1 inch in diameter.
Check out the picture I attached to see this measurement. view full answer...
Yes, there is a roof rack that will fit your 2023 Honda Accord. This mounts directly to the side of your roof without drilling and has more than enough capacity for a bike rack. You will want the roof rack by Rhino Rack and it includes the following parts:
Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 49" Long - Qty 2 item # RRVA126B-2
Rhino-Rack 2500 Series Legs for Vortex Aero Crossbars - Naked Roofs - Qty 4 item # RRRLKVA
Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof... view full answer...
I spoke with my contact at CIPA and found that the Rearview boat mirror, # CM11119, will fit on round or square tubes up to 7/8 inches thick so it will fit a 3/4 inch square tube. view full answer...
Swagman rates their Trailhead 4-Bike Rack # S63381 for a total bike weight load of 140-lbs, or 4 bikes each not exceeding 35-lbs. I confirmed this weight capacity with Swagman.
This hitch rack fits 2-inch hitches installed on passenger vehicles, trailers and RVs. view full answer...
To install the Sportrack Roof Rack part # SR1010 on your 2013 Honda Civic 4 you will need to use the following dimensions.
The front bar scale measurement is 28 inches, the rear bar scale is 26 inches. The placement measurement for the front bar is 12 inches (distance forward of door seams, see pic) and then the rear bar will set 26 inches back from it measured on bar centers. view full answer...
The Curt Hitch # C11391 that you referenced has capacities of 200 lbs tongue weight and 2,000 lbs gross trailer weight. If your 2011 Sea-Doo and trailer fit below those capacities then the hitch would be fine to tow it.
You will need to consult the owners manual of your vehicle to determine what Honda recommends for towing capacities and be sure not to exceed the lower of the two capacities between the hitch and your vehicle. When determining the towing capacity of a setup you should always... view full answer...
Your 325-lb boat and trailer combination is a fairly light tow load but just the same the car maker gets the final word on whether towing anything is advisable. You can check your owner's manual for your specific vehicle since it will reflect the particular version you have (DX, LX, EX, or EX-L) and its capacities. The online version of the owner's manual that I reviewed (page 215) does not prohibit towing in general, so that's a good start. Check your manual (or with your dealership by... view full answer...
The hitch pin that is included with Curt trailer hitch # C11391 is a 1/2 inch pin. All 1-1/4 inch trailer hitches have 1/2 inch pin holes. I have included a link to a video showing an example installation of this hitch for you. view full answer...
I contacted our representative at Hidden Hitch about the Draw-Tite Trailer Hitch, part # 24677.
The representative at Draw-Tite informed me that the thickness of the tubing for part # 24677 is 3/16 inches. The arms of the hitch that connect to the frame of the vehicle are 1/2 inch thick. This is a Class I hitch and is intended for light duty use as it has a tongue weight capacity of 200 lbs.
Part # 24677 does not include a drawbar. If you plan to do light towing, you may be interested... view full answer...
The weight capacity and air pressure ratings on the Dexstar White Spoke Wheel - 15 x 6 - 6 on 5-1/2, part # AM20532, and the Dexstar Galvanized Spoke Wheel - 15 x 6 - 6 on 5-1/2, part # AM20534, is 2,600 lbs at 80 psi.
The Dexstar Black Steel Wheel - 15 x 6 - 6 on 5-1/2, part # AM20514 is 2,600 lbs at 75 psi.
The only difference would be the design and finish of the wheels.
The Dexstar # AM20514 is a solid black steel wheel. The Dexstar # AM20532 and Dexstar # AM20534 are the same... view full answer...
The tongue weight capacity for all of the hitches available for the 2003 and 2006 Honda Civic is 200 pounds. You will need to check your owners manual or with the dealer to be sure that your vehicles tongue weight will support the weight of the bikes and carrier you choose to use.
If you decide to use an extender for the 2 inch rack that you currently have it will reduce the tongue weight of the lowest rated component by 50 percent. So, if the bike rack, hitch and vehicle are all rated... view full answer...
I pulled a Pollak 6-Pole # PK11609 from our warehouse and found that the mounting holes are 2-3/4 inches apart and the diameter of the tube on the back of the connector is 1 inch. view full answer...
I went out to the warehouse to measure Camco RV Replacement Plumbing Vent w/ Putty and Screws - Polar White Item # CAM40033 for you. From the mounting surface to the top of the vent it is 3 inches.
We also have Ultra-Fab Solar-Powered Plumbing Vent for Motor Homes - 7" Diameter x 3-3/4" Tall
Item # UF53-945001 which is 3-3/4 inches tall.
For a galvanized model we have Ventline Plumbing Vent - Galvanized Steel - Mill Finish Item # V2084 which is 3 inches tall. I have linked videos of all... view full answer...
The best way to determine which amount of rise or drop you need from a ball mount (in order to keep your hitched trailer level for the best handling) is to measure as outlined in the linked article. Since the same wheel size could have more than one tire size on it that does not give you the best method for choosing a ball mount.
For the Class I hitch on your 2015 Honda Civic you can refer to the linked page to see all ball mounts. view full answer...
The inside dimensions of the 24x60 Curt Cargo Carrier for 2" Hitches # C18152 are 60" long x 24" wide x 6" deep.
Attached is a review video for you to check out as well as a dimensional photo for you to reference. view full answer...
When the SportRack semi-custom roof rack # SR1002 is installed on your 2012 Honda Civic sedan the bar spread will be 25 inches. Bar spread is measured from the center of one bar to the center of the other bar. I have linked a video review of the roof rack for you. view full answer...
No, it will not. There are no 2" hitches available from anyone for a 2018 Honda Civic. The only hitches available are class I 1-1/4" hitches due to the small size and capacity of a Honda Civic.
To add a hitch to your daughter's 2018 Honda Civic sedan, I recommend the Draw-Tite item # 24954. This hitch is custom fit and mounts behind the rear bumper cover. The only portion visible is the 1-1/4" receiver which not only looks better but helps with ground clearance.
I have linked an installation... view full answer...
To add a roof rack to your 2014 Honda Civic Si Coupe you will want the roof rack by Yakima and it includes the following parts:
Yakima JetStream Crossbars - Aluminum - Black - 60" Long - Qty 2 item # Y00426
BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 item # Y28TR
BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 item # Y06125
BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 item # Y06143
This roof rack attaches to the groves inside your door... view full answer...