bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about BMW Trailer Brake Controller


  • Wiring Tekonsha Primus Trailer Brake Controller On a 2024 Chevrolet Tahoe
  • For the Tekonsha Primus IQ Trailer Brake Controller # TK90160 you will run the wiring as noted below for your 2024 Chevy Tahoe wiring. Black(brake controller) to Red/Black(Tahoe) White(brake controller) to White(Tahoe) Red(brake controller) to Lt Blue/White(Tahoe) Blue(brake controller) to Blue(Tahoe)
    view full answer...

  • Can a Factory Trailer Brake Controller be Replaced With Aftermarket on a 2018 Silverado 1500?
  • First you are going to have to have the programming removed from you ECU for the factory trailer brake controller. As I assume you liked the clean looks of the factory controller I would recommend the Redarc Tow-Pro Elite Brake Controller # RED44FR. This has a small dash mounted control knob for a clean appearance and simple operation. To connect to the factory wiring you will need the Plug-and-Play Wiring Harness # 331-TPH-010.
    view full answer...

  • Best Brake Controller for a 2018 Jeep Grand Cherokee
  • I would be happy to! The best brake controller for your 2018 Jeep Grand Cherokee Limited is going to be the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness item # RED52VR. This is a proportional brake controller that activates your trailer's brakes when your Jeep decelerates. This the safest and most reliable way to slow your trailer without adding additional stress to your Jeep and trailer. The reason the Tow-Pro Liberty is the best option is because of its unique...
    view full answer...

  • Recommended Brake Controller and Adapter for a 2018 Ford F-150 w/ a Factory 4-Way
  • We don't have a way to look it up but if that 4-way connector came with your 2018 Ford F-150 from the factory then you definitely have the brake controller port. It'll be located below your steering wheel behind the panel on the right. I have linked a video below and attached a picture that will help you find the brake controller plug. I recommend the Redarc Tow-Pro Liberty Brake Controller item # RED24FR. This is a proportional brake controller that activates your trailer's brakes when...
    view full answer...

  • Parts Needed To Install a 7-Way and Trailer Brake Controller on a 2017 Jeep Wrangler With 4-Way
  • The Universal Installation Kit # ETBC7 you found will allow you to install a 7-way along with a Redarc Tow-Pro Elite Brake Controller # RED44FR. The kit contains a 7-way which will plug into the 4-way you already have and includes wiring to run to and wire in the brake controller as well as a charge line to maintain the breakaway battery on the trailer. The Redarc # RED44FR is great for your 2017 Jeep Wrangler as it has a small control knob which you can mount to your dash and will not...
    view full answer...

  • Can The Tekonsha Vehicle Wiring Harness Be Installed on 2020 Kia Sedona Without Brake Controller?
  • Yes, if you are not ready to install the Redarc Tow-Pro Elite Brake Controller # RED63RR when you install the Tekonsha OEM Replacement Vehicle Wiring Harness # TK24FR on your 2020 Kia Sedona you do not have to install the black battery cable which powers the brake controller. If you know you are going to install the brake controller sooner than later you might just go ahead and connect the wire to the battery and into the rest of the harness. Then just remove the fuse so when you are ready...
    view full answer...

  • Should The Curt Triflex Controller Flash The Output Setting When Beake Pedal Is Pressed?
  • Hey Russ, so what you are describing is completely normal for the Curt Triflex brake controller. The maximum output setting is shown on the display when a trailer is connected and the brake pedal is pressed or the manual control is actuated. If a trailer is not connected the output setting is flashed when the brake pedal is pressed or the manual control is actuated.
    view full answer...

  • Recommended Plug and Play Brake Controller Adapter for a 2022 Nissan Pathfinder
  • No, I am sorry we do not because Tekonsha did not make one for your 2022 Nissan Pathfinder. The Prodigy P3 Brake Controller item # 90195 includes a universal harness you can use but you'll need to cut and splice wires. Curt does have a plug in play adapter but it only works with their brake controllers. It is the Curt Custom Wiring Adapter for Trailer Brake Controllers item # C51382. It will allow you to easily install the Curt Spectrum Trailer Brake Controller item # C51170.
    view full answer...

  • Can Aftermarket Brake Controller Replace OEM Controller on a 2009 GMC Sierra 2500HD
  • Hey Steve, thanks for reaching out! Yes, you can install an aftermarket controller like the Prodigy P3 # 90195 to bypass the OEM controller on your 2009 GMC Sierra 2500HD. You're going to have a bundle of blunt-cut wires under the driver side dash of your truck that you'll need to connect to the pigtail that comes with the P3 with the following connections: GM Wire to Brake Control Wire Function: - Red/Black to Black Battery Power - White to White Ground - Light Blue/White to Red...
    view full answer...

  • Troubleshooting Brake Controller of 2014 Ram 2500 Stopped Working When Accy Circuit Fuse Blew
  • If the guy who installed your brake controller did his homework he should have gotten power for the brake controller from the factory wiring that was designed for brake controller installs and not from the 12 volt accessory circuit that you replaced the fuse on. So I would check to see where the black wire of you brake controller wiring is ran to. There should be a separate fuse for the brake controller power circuit though which would be the correct one to replace to get the controller...
    view full answer...

  • Installing Brake Controller on 2020 GMC Canyon With Tow Package
  • Hi Harold, When installing a brake controller like the Prodigy P3 # 90195 or Redarc Tow-Pro Elite # RED44FR on your 2020 GMC Canyon with the tow package, all you need to do is connect the wiring that comes with those controllers to the wires already run under your dash. I did some searching and found that on page 211 of the Canyon owner's manual it says a four-wire harness is secured behind the left side kick panel (which is the driver's side), and here are the wires in your truck (though...
    view full answer...

  • Brake Controller Not Connected to 2008 Chevy Silverado 2500
  • Hi Shane, Thanks so very much for your purchase from etrailer of the Tekonsha Prodigy P3 Trailer Brake Controller # 90195. We appreciate your business and the issue with it not being connected could be due to how a brake controller installs on certain year Silverado's, including 2008. What you need to do is activate the brake controller and 12 volt power post connections under your hood. It's somewhat lengthy so I have added a link below to a help article which details how to do this.
    view full answer...

  • Options For Adding a Trailer Brake Controller 2015 American Coach Tradition RV Freightliner Chassis
  • There used to be a plug and play option available from Tekonsha with their 3027-P adapter which would allow you to use one of their controllers like the Prodigy P3 # 90195. Since that is no longer available from Tekonsha you could cut off the factory connector and wire in the Controller # 90195 or use a trailer mounted option like the Autowbrake # 3430001 you found.
    view full answer...

  • Curt Brake Controller Wiring Plug for a 2021 Chevy Silverado 1500
  • Thanks for reaching out, Alan! In order to install a Curt brake controller to your 2021 Chevy Silverado 1500 you'll need the Adapter # C51525, yes. This will connect under the dash to that larger gray connector you found. If you don't already have the brake controller then I really like the Curt TriFlex NEXT Trailer Brake Controller # C24VV as it has a proportional operation so the trailer brakes match the time and intensity of your truck braking.
    view full answer...

  • Tekonsha P3 Shows 0.0 On Display When Brake Pedal Is Pressed - Is Something Wrong?
  • Hello Chris. What you are describing sounds completely normal and it sounds like your Tekonsha P# controller # 90195 is installed correctly. With the trailer connected the display should show 0.0 when the brakes are applied, and it should show the current gain setting when the manual override is applied. The P3 has an internal inertia sensor. It senses deceleration and generates an output that is based on deceleration. When the vehicle is not in motion, the controller will not sense deceleration...
    view full answer...

  • Recommended Trailer Brake Controller and 7-Way For a 2022 Toyota RAV4 Prime
  • Personally Jay, I have never been a fan of the Curt Echo in any of its forms # C79DR, # C51180 or # C27JR. They seem to have a lot of connection issues which causes them to not perform well. As you already have a 4-way I recommend using our 7-Way Kit # ETBC7 which provides you with a connector which plugs into your 4-way and the wiring for a charge line and Brake Controller # RED52VR. This Redarc controller has a small dash mounted knob which is easy to use and the proportional braking...
    view full answer...

  • Finding the Cold Side of the Stop Light Switch for Installing a TBC
  • Hey Ronnie, so to connect your brake controller like the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 to your stop light switch, you're going to need to find the wire that only gets power when the brakes are pressed. Once this wire is identified, you'd need to connect the red wire to this and then the black to the positive battery, white to the ground wire, and then blue to the trailer brake.
    view full answer...

  • Is the Tekonsha Commander a Time Delayed Controller?
  • The obsolete Tekonsha Commander is a time delayed brake controller. The knob on the left hand side is the level knob. This sets the brake controller sensors to level which is and essential part of setting up the brake controller was it is installed. The knob on the right hand side of the controller is the power knob. This adjusts the amount of power output to the electric trailer brakes. The Tekonsha Voyager item # 39510 is what replaced the Commander and here are the instructions for...
    view full answer...

  • Availability of Plug and Play Wiring Harness for Brake Controller in RV on 2022 Ford F-53 Chassis
  • There are no custom wiring harnesses for installation of a brake controller on your F-53 RV. Installation of the Tekonsha Primus # TK90160 or any other brake controller will require splicing for installation.
    view full answer...

  • How to Find Instructions for Adjusting a Brake Controller in Spanish
  • A lot of the manuals for trailer brake controllers will have a section in Spanish. For example, the Tekonsha Prodigy P2 # 90885 has the instructions listed out in English, then French, and then towards the bottom is Spanish. The instructions for this controller are attached to this page for you to check out. I wasn't able to find any instructions for an OEM controller for your Chevy Silverado though. If you have a specific brake controller in mind just let me know and I'd be happy to...
    view full answer...