We had one customer come back and tell us that in a heavy rain the fabric straps of the Yakima EasyTop Universal Fit Roof Rack part # Y07418 did allow some water to drip into the interior of the vehicle. Unfortunately there's no way to avoid that unless you'd be willing to install a roof rack like the Rhino Rack part numbers # RRVA137B-2, # RRRLKVA, and # DK318 which is a much more secure rack for your 2013 Chrysler 300 and will not leak. view full answer...
The trailer hitch options for 2013 Chrysler 300 are all compatible with the S models. I recommend going with the larger 2" opening due to the higher capacity and abundance of hitched mounted accessories for this size. The Curt Trailer Hitch Receiver part # C13093 offers a bolt-on fit with no drilling required. view full answer...
Two sizes and weight classes of hitch are offered for your 2008 Chrysler 300. These include several of the 1-1/4-inch Class II type and one of the 2-inch Class III type. All things being equal I suggest the 2-inch Class III hitch # 13465 from Curt since this size hitch will be more widely compatible with a range of hitch-mount accessories like bike racks and cargo carriers. An install video is linked.
All you will need to add is the hitch ball, either a 1-7/8-inch (# 19256) or 2-inch... view full answer...
The two most likely causes for the blown 12V power fuse that feeds your TowReady T-One Vehicle Wiring Harness # 118544 are a short within the trailer wiring for its running light circuit or excessive current draw from the clearance/marker lights on your trailer.
If you happen to have access to either another tow vehicle or trailer you can try substituting one in place of yours to see if the issue remains. This is the easiest way to isolate the fault to either the vehicle or trailer.
If... view full answer...
Check to make sure the fuse is in the fuse holder of the Curt trailer wiring kit part # C55546 as well as the white wire is grounded properly. Typically when this problem arises the issue is the fuse not being installed. view full answer...
For your 2011 Chrysler 300, we offer the Curt T-Connector, # C56145.
I have attached an installation video on a 2013 Chrysler 300 for you to check out.
While this is a plug and play unit, you will have to run the main power wire up to the vehicle battery. These wiring harnesses require a direct 12v connection to the battery to power the trailer or accessory lights. This is to protect the vehicle's tail light circuits from overloading. I have attached a help article on tips for routing... view full answer...
Yes, Curt trailer hitch # C13093 fits all models of the 2014 Chrysler 300 including the base models.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use... view full answer...
I checks Saris's web site and they do confirm the fit for the Saris Bones 3 Bike Carrier part # SA801BL on your 2017 Chrysler 300S. view full answer...
I checked the install instructions for the Curt hitch part # C13093 that you referenced which is a fit for your 2014 Chrysler 300C and there is no mention of rear fascia trimming or removal so that's not something you would have to worry about.
Now for a trailer wiring mounting bracket the part # 18144 would be a great option to use to hold the 4-way connector of the part # C56145 which is a fit for your vehicle as well. This bracket actually attaches to the rear bumper of the vehicle... view full answer...
Your 2005 Chrysler 300 has the 42RLE transmission in it which means the top line is the return line and the line the cooler should be installed on like the # D15902 and the bottom line is the send line. view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver part # 76145 is what I recommend for a 2008 Chrysler 300. It has a class III rating with 2" receiver tube opening which will allow for a greater towing capacity and more ball mount options to choose from when compared to the other class II, 1-1/4" receiver tube options. In order to complete your towing setup you'll need a wiring harness, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C55546 and a ball mount/hitch... view full answer...
Yes, we do carry multiple hitches, ball mounts, that are similar to the Convert-A-Ball Ball Mount for 2" Hitches item # AMSC12 you were looking at. The closest comparable product would be the Brophy Trailer Hitch Ball Mount 10" Drop, 7,500 lbs item # BM10. If you have some more specific requirements please email me back with them and I can make a better recommendation. I have linked our entire selection of fixed ball mounts below. view full answer...
You are correct. The RoadMaster 4 Inch Hi-Lo Drop, part # RM-070 is meant for use with a tow bar used for towing a vehicle.
It is meant to tow a rolling load, not a situation where more than 100 lbs of downward force is applied to it. view full answer...
Really and truly there's only one option for a hitch on a 2014 Chrysler 300 with the heft to carry something as robust as an electric scooter, and that's the 2 inch hitch from Draw-Tite:
- Draw-Tite Max-Frame Trailer Hitch Receiver # 76145
The # 76145 has a 4,500 lb towing and 675 lb tongue weight capacity, both of which are far ahead of what any other hitch for this vehicle can offer. Your customer will need to keep in mind they are limited by the lowest-rated factor, so they'll need... view full answer...
I have a way for you to transport and use a roof top tent, like the Yakima SkyRise HD Tent # Y07436, with your 2014 Chrysler 300 but every roof top tent I've looked at says not to mount and use a tent on a roof rack that uses clips for the door jambs like what we see with this Yakima setup. The 165 lb weight rating is the dynamic rating so the static rating would be higher, but we need to look at a different solution since a clip-style roof rack shouldn't be used for this application.
As... view full answer...
The important thing to remember is that the trailer hitch is rated for 3,500 pounds. If the vehicle is rated lower, which in this case it is, you go by the lower rating. You would not want to go beyond the capacity specified in your vehicle owners manual.
I have included a link to a video showing a typical installation for you. I have also included a link to the installation instructions. Since you are planning on doing some towing I recommend the etrailer ball mount kit # EBMK4. It comes... view full answer...
The Superchips programmer part # SU3845 does fit your 2008 Chrysler 300 that has the 3.5 liter engine and it does have ability to make changes to some transmission settings like shift points and shift firmness but it does not have ability to do any Chrysler updates. view full answer...
The trailer hitch options for a 2019 Chrysler 300 don't require drilling, they install via pre-drilled holes in the frame. I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver part # 76145 which has the larger class III, 2" receiver tube opening which is more versatile than the class II, 1-1/4" opening in regards to towing, bike racks, and cargo carriers.
In regards to trailer wiring, the T-One Vehicle Wiring Harness part # 118658 is what you seek as it's a direct fit or plug-in-play.... view full answer...
I do have a solution, but Inno has discontinued the fit kit for your 2017 Chrysler 300. Unfortunately, other fit kits will not allow you to install this roof rack on your vehicle. What I can offer instead is a Yakima roof rack like the CoreBar rack, which is similar to the # INXB108-115. You will need the following parts to complete the rack:
-Yakima CoreBar Crossbars # Y00421
-BaseLine Towers # Y28TR
-BaseClip Fit Kit # Y06110
The Yakima JetStream crossbars # Y00425 will work with... view full answer...
We have several vents that might work for your Streamline trailer but nothing that is made specifically for it. I have included a link to the right to the options for you. Most of the vents require a 14-1/4 inch square opening to install the vent.
The majority of the vents have plastic lids with a few exceptions that have metal lids. Beyond that it is just a matter of the color you want: white, blue, smoke, silver, clear, and metal.
I also recommend the vent installation kit # 344270KITW. view full answer...
Go To Results