The Dexter DX7.5 Drop-N-Go Brake Actuator # 099-175-20 should be wired to the reverse light circuit on your 7-way. Although I do not have a specific wiring diagram, this is a simple process. There are two wires on your brake actuator. One will be the ground and the other connects to the reverse lights. These are interchangeable so you don't have to worry which you use.
The reverse lights should run to the middle pin on your 7-way connector. The wire color is typically going to be yellow... view full answer...
The Automatic Changeover RV LP Gas Regulator # 37207-30395 will indicate RED for an empty tank or if it does not detect propane.
If you have your tanks turned off it will stay red. When you turn a tank on the valve indicator will turn green. It does not read both tanks at the same time, It will only tell you the status of the tank that the black lever on the top of the unit is switched to.
I have linked a video guide that will show you this in real time and explains the process. view full answer...
We have a couple of great options I'll go over for you, but in regards to the Kuat NV 2.0 Bike Rack # BA22B, this is a fantastic rack, but it is not rated for use behind any RV or motorhome. What that means is even though it may work fine, if anything should happen then it will not be covered by its lifetime warranty, and that's a gamble that a lot of people aren't willing to take considering its price.
I recommend the Hollywood Racks Sport Rider SE2 2 Bike Platform Rack # HLY84FR.
The... view full answer...
We don't have an install video but what I can do is describe it. The portion of the # LC301704 with the round holes mounts to the bottom of the frame on your trailer with nuts and bolts or welding. They would need to be spaced at the width of your steps. Then the square hole side of the outrigger is used to run the included hardware through to attach to the step. If the mounting hardware from your old steps is too rusted or damaged then you can use the hardware kit # LC118155-72 for installation... view full answer...
I would be happy to go over how to install the Tekonsha Prodigy P2 # 90885 you were looking at in your 2001 Winnebago Brave Motorhome built on the Workhorse Chassis, but there is not a plug and play option available for the Workhorse Chassis.
Instead you will need to use the Wiring Kit # 5506 and like some extra wire # 10-2-1 due to the length of your RV to get the controller installed.
You will need to make the following connections to the controller wiring harness:
Red wire to cold... view full answer...
The monitor and sensors included with the TireMinder A1AS TPMS for RVs and Trailers # TM79FR each have a different battery life.
According to the manufacturer, the monitor lasts for 2 days when fully charged. It is, however, rechargeable and has a recharge time of 6 hours. The tire sensors have a battery life ranging from 9 to 14 months. view full answer...
Standard incandescent "bulb" lights are not polarity sensitive as some LED lights are so when installing Optronics Incandescent Trailer Clearance Light # MC32RBB it does not matter which pigtail lead you connect to ground or hot. view full answer...
Currently we have no way to verify if the Lippert SolidStep RV Steps for 29" to 36" Wide Doorways - 3 Steps # LC791573 will fit the 2014 Winnebago One 30RE. I have linked our help article near the bottom of the page which will take you through the necessary steps to verify if you will be able to add steps to this camper. view full answer...
The Curt Class 5 Universal Weld-on Hitch part # C87CR is designed to be welded to the frame of a vehicle. I cannot recommend bolting and drilling unfortunately. The frame will need to be clean and clear of obstructions before welding. In regards to the actual welding, this would need to be done by a trainer professional, make sure precautions are taken such as unhooking the battery. That said, I'm no welding expert so you would need to refer one for these types of questions. view full answer...
The correct SumoSprings Custom Helper Springs for your 2018 Winnebago Sunstar 31BE (that features an 18,000 pound GVWR), which is the part # SSF-170-40-2 for the front axle and # SSR-184-40-1 for the rear axle, will not require any drilling during installation. These are complete bolt-on applications that will simply replace the factory bump stops on the Ford F-53 chassis.
I have attached a couple short video demonstrations along with the written installation manuals for these kits that... view full answer...
The Jensen Stereo -AM/FM - CD/DVD - USB - Bluetooth # JWM60A is a great replacement for your Jensen AWM970. There is not a wiring harness to match your old harness to the new one, but I have attached the photo from each harness to help you with mating functions so it will be easy to swap out. view full answer...
Yes, the Roadmaster Exact Center Steering Stabilizer with Custom Brackets for Ford F-53 Chassis, # RM36RR will have a installation instructions included.
I also highly recommend the Roadmaster Anti-Sway Bars, # RM-1139-146 for the rear and, # RM-1139-148 for the front to minimize side-to-side movement and improve overall stability of your vehicle. view full answer...
To easily fit the center portion of the Epicord Battery Disconnect Switch # 277-000096 through your wall you'd want to drill a 2-3/4 inch hole so that would be the size hole saw to use. view full answer...
In regards to the Furrion Vision S Wireless RV Observation Camera System part # FCE48TASL-05, you shouldn't need to run any new power wires so long as you already have a similar system in place. The main overhead camera will simply just use the same power wire your existing system uses. If you did not have an existing power wire you could just run a wire up spliced into the running light or back-up circuit, but this does not pertain to you since you already have a system in place that you... view full answer...
Yes, once installed the Firestone Ride-Rite Air Helper Springs # F2603 will reduce the strain on your rear suspension. The # F2603 helps prevent permanent sagging and excessive friction on leaf springs. It will also reduce tire wear and improve steering control. These air helper springs absorb road shock and soften contact between the frame and axle to prevent bottoming out.
I would also recommend adding an air compressor like the Firestone Air Command II # F2168. This is a dual path system... view full answer...
The outer brackets (hexagon heads) have changed with the Solera 5000 Series slide toppers so you'll have to slide them off of the inner brackets to install the Solera RV Slide-Out Awning # LCV000165062. You can leave the inner brackets mounted to the wall of your slide out and simply slide on the new outer brackets to get the slide topper installed.
On a side note, It looks like you might have slightly too big of a slide topper on the slide out and it's causing too much tension on the... view full answer...
That depends on the vehicle, but most vehicles only require putting the key ignition into the ACC position to unlock the steering wheel so that it can be flat towed. If you check the owners manual of your vehicle this would be covered under the recreational towing section. view full answer...
Weight distribution can help reduce sway when towing but it does not always stop all of it. The best solution would be to move any weight in your trailer forward to increase the tongue weight and also make sure the trailer is sitting as level as possible.
Or you could go with the Curt True Course sway control part # C94VV which has a sensor that can detect when your trailer is swaying and applies enough brake to stop it. view full answer...
Furrion states that there really is no minimum for things that are mounted on the same wall. You wouldn't want the fireplace blowing directly on anything combustible. The fireplace has a proximity sensor that will shut it down if an object is placed within 6 inches in front of the fireplace, it'll shut down until the object is removed and the power switch is cycled.
Other than that, there are no further limitations. If you click the provided link, you can see a product description video... view full answer...
The wires on the Lippert Replacement Atlas Jack for Kwikee Level Best Hydraulic Leveling System # LC359278 aren't polarity sensitive so you just connect one to power and one to ground. I reached out to my contact at Lippert and he said you just connect the hydraulic lines to the jack and then it will get filled from the tank when you turn it on. view full answer...
Go To Results