There is a ball mount with 1-7/8 inch, 2 inch and 2-5/16 inch hitch balls, though the Channel Style Adjustable Ball Mount # C45900 you asked about does not have a separate 1-7/8 inch hitch ball attachment.
Instead, I recommend checking out the Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches # D900 which has a 1-7/8 inch hitch ball with 6,000 lb capacity, a 2 inch hitch ball with 7,500 lb capacity and a 2-5/8 inch hitch ball with 10,000 lb capacity. This ball mount has a maximum... view full answer...
The Draw-Tite Class III # 76031 hitch installs using six M12 x 1.25 x 35mm CL 8.8 bolts, 1/2 inch flat washers and lock washers.
If your Pathfinder has been used in the rust belt where chemicals are used on road surfaces in the winter, there's likely some road grime and corrosion in the nuts that are welded up into the frame that accept the hitch mounting bolts. Before attempting to install the bolts, It's a good idea to spray each hole thoroughly with a spray lubricant like WD-40 and... view full answer...
The price for the Westin Signature Series Step Bars, Black Powder Coated, for Nissan Pathfinder, part # 25-1225, includes the cost of both nerf bars and all the required installation hardware. It is custom fit for your 1997 Nissan Pathfinder 4 door, and you should have no problems installing these bars on your vehicle. view full answer...
The Airaid # AR523-284 you were looking at for your 2013 Nissan Armada is actually an open air system, because the unit is not fully encased.
The main advantage that the open box systems have over the enclosed box system is that open systems offer the maximum amount of airflow. The enclosed box systems will still have plenty of air flow, just not as much as an open box system. The closed air systems will look like the picture I have linked to this page for your convenience.
Another main... view full answer...
The Curt Trailer Hitch # C13304 comes only with the trailer hitch and hardware needed to install it on your 2018 Nissan Titan, but we do have wiring kits that are available as well.
For a 4-Way wiring kit I recommend the # C59496 which comes with all of the wiring and connectors that you need. This kit draws power directly from your battery so as to protect the wiring on your Titan.
If you are needing a fully functional 7-Way then you will also need to install the Hopkins # N40975 if... view full answer...
The Curt Trailer Hitch # C11349 does not come with wiring for your 2014 Nissan Sentra SV but if you are needing wiring you'll just need the Curt # C56205.
To complete your towing setup you'll also need the Curt Ball Mount # C45521 with the Pin & Clip # F-4 and either a 1-7/8" # A-80 or 2" # A-82 hitch ball.
We haven't had the chance to install any of these parts yet but I'm linking the instructions for you to check out. view full answer...
Yes, the photo on our web page is of the actual hitch. If you mouse over the image links below the title you will see more actual pictures of the hitch and the display image shows the hitch from the underside of the vehicle. The Photo of the Draw-Tite Class III Trailer Hitch, item # 75148, is also the actual photo but we have not had the opportunity to photograph it on the vehicle. We also have a video installation of the Curt Class III Trailer Hitch on a 2007 model Nissan Murano (see link).... view full answer...
I called my contact at Curt and they told me you have one of the newer design wiring harnesses they have manufactured.
You will need a 10 amp fuse for the inline and will also need to replace the fuse in your vehicle with a 10 amp fuse as well. They told me that they are updating their instructions to show the newer harness but the older instructions seem to have made it in the newer packaging. view full answer...
The Class III # 75282 Draw-Tite Trailer Hitch that you are interested in does comes with the six bolts needed to secure the hitch to the existing weld nuts in the frame. All of our hitches are shipped with the necessary installation hardware.
If you click the provided link, you can view an install video. view full answer...
Replacement Wiring Harness # 118267 for your 2010 Nissan Frontier doesn't really have a gasket at the 7-Way lid. And for something to be considered waterproof it has to be able to be submerged under water for a certain amount of time and not let in any water. No trailer connector can make that claim! What I recommend to safeguard against corrosion from moisture is to use dielectric grease # LT37534 anywhere you have electrical connections.
The other option is to use a factory replacement... view full answer...
Yes, the special installation tool is included with the vehicle specific clamp kit (part # DK047) for the Rhino Rack roof rack system. This roof rack system is composed of the # DK047 which is the clamp and pad system that is custom fit for your vehicle. Then the # DA118 is the crossbar system for the clamps that fit your car.
I have included a photo of this installation tool and a video showing the installation of this roof rack system on a similar vehicle to yours. view full answer...
The Draw-Tite # 75282 does include all the necessary hardware and is confirmed to fit your 2016 Nissan Frontier. I've linked an install video for you.
If you're going to be towing a trailer you'll also need a ball mount, hitch ball, pin and clip, and trailer wiring.
A wiring harness that will fit your truck is # C56225. This will provide a 4-way trailer connector and installs by plugging in to a connector beneath the vehicle. Then connect the included jumper harness with relays into... view full answer...
The Draw-Tite # 75282, which is a confirmed fit for your 2018 Nissan Frontier, does not come with a bracket for a 7-way. What you want to use is Mounting Bracket and Installation Hardware # PK12711U; I've added links to a video review of this bracket as well as a link to a video of this hitch being installed on an '18 Frontier. view full answer...
The Timbren Suspension Enhancement System # TNRXT4 you were looking at for your 2002 Nissan Xterra do come as a pair and include the vehicle specific mounting brackets and hardware needed for the install.
I included a video of the # TNRXT4 for you to take a look at. view full answer...
No, the etrailer Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles - 10 Diameter - 5 on 4-1/2 Item # AKHD-545-35-EZ-K that you referenced comes as a single hub and drum assembly so you need to purchase 2 of them for each axle on your trailer.
Attached is an installation video that you can check out. view full answer...
Due to the profile of the Curt Class III trailer hitch # C13126, most of the hitch crossbar is recessed under the rear fascia of a 2013 Nissan Pathfinder. Therefore this hitch does not include a mounting location for trailer wiring.
Since there is limited space on the hitch crossbar, a mounting bracket is not included on the hitch. Additionally, the rear fascia has to be trimmed to complete the installation of this hitch. I have included a photos showing this hitch installed on a 2013... view full answer...
The Pollak 7- and 4-Pole Trailer Connector Socket with Mounting Bracket # HM40975 comes with the trailer connector, mounting bracket, and 2 self-tapping screws. I have attached photo showing the included parts.
There is no wiring harness included with # HM40975. I have also attached a photo showing what the socket on the back of the connector looks like. This socket should mate with a plug already on your 2014 Nissan Pathfinder with factory wiring harness.
I have attached an installation... view full answer...
The Malone EcoLight Sport Trailer part # MAL43FR comes with eight half arm brackets, everything needed to carry two kayaks. The first photo shows the complete trailer and what it will look like assembled. In order to use this trailer with a 7-way trailer connector, you can use the 7-Way to 4-Flat Adapter part # 47345. view full answer...
Your Draw-Tite hitch # 75186 that fits your 1998 Nissan Frontier includes among its hardware items four fish wire tools, also called bolt leaders. These are supplied to make it easier to place the carriage bolts and bolt plates inside the frame rails on models with the 56-inch bed. They are typically not needed to install this hitch on the 75-inch bed model.
Page 2 of the linked instructions refers to these bolt leaders. view full answer...
Go To Results