The Curt # 13088 will require absolutely no drilling to get installed on your 1996 Nissan Pathfinder. This will bolt right into factory weld nuts that are already in your frame, so it's a nice easy install.
With that being said, these weld nuts can get clogged up with debris over time, so you may need to clean them out before the install. This is pretty common and all you need to do is soak them with WD40 and then scrub them out with something like the Nylon Tube Brush # 814092. This is... view full answer...
Hey Tony, for your 2020 Nissan Murano we only have 2 inch hitches that are Class III like the part # e98907 available. Most of the time this is the preferred hitch size as it has the most accessories made for it and the best capacities. view full answer...
Yes, you are going to be able to use the Kuat Transfer V2 Bike Rack # KU64FR with your 2022 Nissan Frontier as long as you have a receiver. If you do not have a receiver from the factory you can use our etrailer Trailer Hitch Receiver # e98869 to carry the bike rack.
Anytime a receiver is put on a vehicle I recommend also adding the Wiring # 118266 in the event you ever need to pull a trailer or use Auxiliary Lights # C53201 with your truck. view full answer...
Yes, the # DT65RR includes the 6 bolts, flat washers, and lock washers required to install the # 75282 on your 2022 Nissan Frontier. view full answer...
The Curt Class 1 Hitch # C11264 which is a fit for a 2005 Nissan Maxima I can confirm does not come with a hitch pin and clip. That said, we do sell this separately using the Pin and Clip For Class I and II Trailer Hitch Receiver Hitch part # PC2. The pin and clip is usually included with the accessory but very rarely if ever included with the trailer hitch.
I have attached a list of some hitch mounted accessories you may be interested in as well below view full answer...
Great question, Mike!
The Air Lift 1000 Air Helper Springs # AL43WQ will help support the OEM suspension on your 2023 Nissan Rogue but they won't increase the tongue weight capacity for your vehicle - this is the case for every suspension enhancement for any vehicle.
The only time I've ever seen a vehicle with the option to increase the weight capacity is when a "tow package" can be added, which in turn gives the vehicle more durability. You'll have to reach out to Nissan to see if there... view full answer...
I hope I am fully understanding that you want to have both a 4-way and 7-way on the back of your 2007 Nissan Xterra. The Curt T-Connector Vehicle Wiring Harness # C56226 is the correct harness to give you a 7-way, but the Replacement Harness # 118263 is for the Tekonsha and will not fit with the Curt already connected. Instead you should get the Curt and replace the end with the Multi-Connector # HM40950 which will plug right in place of the Curt 7-way and you will have both the 7-way... view full answer...
The two vehicles you mentioned are different enough that they require totally different trailer hitches. So for your 2010 Nissan Xterra you'd need a hitch like the Curt Class III part # 13514 which is a custom fit. I attached an install video for this hitch on a similar 2010 Xterra as well.
There also would be no way to modify a hitch from another vehicle to fit yours either. view full answer...
The 30" Ark Drop Down Corner RV Stabilizer Jacks # ARK94FR have a weld on design. This is the only way to install the jacks with the included mounts as there is not enough room between the stabilizer itself and the mounting plate for additional hardware.
We do have the shorter Stallion 22-1/4" Stabilizers # 288-01892-2 which do offer a bolt on installation if the length of the jack will work for your application. view full answer...
Hi Robert,
Yes, both the Tekonsha Primus IQ # TK90160 and Plug-In wire harness # 3050-P would be a compatible fit for your 2018 Nissan Armada. To activate the brakesYou'll also need a 7-way socket at the back of your Armada for the trailer to plug into and receive the signals from the Armada. If you don't have a 7-way but do have the factory connector tucked up back there then you can just install the Hopkins # N40975.
If you don't have a 7-way you'll need to first check if you at least... view full answer...
It sounds like you're having issues with your trailer lights working but your connector at the vehicle is getting power. You should start with your ground to ensure it has a solid connection to a clean section of your trailers frame or piece of metal if your trailer is aluminum. Make sure there is no corrosion, rust, dirt, or paint between the ground and the attachment point. If your ground is good and you're still having issues
I recommend using a circuit tester like item # PTW2992.... view full answer...
Hi Anwar, thanks for reaching out!
The Timbren Front Suspension Enhancement System # TFXF1004A will fit just fine on your 2016 Nissan Titan XD, although we don't have any photos of this installation as of yet. Timbren has confirmed this will fit so you can be confident it will work as it's designed to work. view full answer...
I would not recommend the B&W Continuum Weight Distribution System # BW78FR for your 2022 Jayco Jay Flight SLX 8 264BH as you only have 470lbs of dry tongue weight. The B&W requires at least 600lbs of tongue weight to work properly.
I recommend the Fastway e2 # FA92-00-0800 for your Jayco. This hitch is rated for a tongue with of 400 to 800lbs with a maximum trailer weight of 8,000lbs. Your Jayco can only weigh up to 6,000lbs so you so it will meet all the criteria for this weight distribution... view full answer...
I went to our warehouse and took these measurements off the Draw-Tite Max-Frame Trailer Hitch Receiver # 75186. All the measurements are from the center of hole to center of the next hole. For the width it is 39-3/4" on center. Starting from the rearmost holes when it would be on the vehicle they are 2" on center, 5" on center and 3" on center.
I have also linked the installation instructions for this receiver near the bottom of the page since not all of the mounting holes are used for... view full answer...
Hey Stephen,
Tailgate seals like the TrailSeal Tailgate Gasket # 834532001583 are universal fits so it really just comes down to style of the gasket in my opinion. This seal has a flat surface which I find typically makes great contact with tailgate but if you ever get anything sticky on it will annoy the hell out of you sticking to the tailgate and start to pull away from the bed. I've also seen this bit when it's extremely hot out with other seals and I'm personally not a fan.
I'd... view full answer...
A LED Brake Light Hitch Cover will fit into the etrailer Trailer Hitch Receiver # e93ZR you installed on your 2021 Nissan Rogue. The light needs to plug into a 4-way flat connector so you will also need the Curt T-Connector Vehicle Wiring Harness # C44ER to install on your Nissan Rogue. Hitch covers with a light like this will all use this style connector since the vehicle is most likely going to have trailer wiring with a trailer hitch receiver installed. view full answer...
Hey Paul, we have a Blue Ox base plate kit that fits your 2024 Nissan Versa with the part # BX1856.
In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle. One of the most popular compatible tow bars is the Blue Ox Avail # BX7420 which comes with safety cables. The coiled design helps keep the cables off of the ground.
For lighting you can use the diode kit, # RM-15267, and not have to worry... view full answer...
The Curt # C17332 Short-Arm distance from the center of the trailer ball to the approximate center of the frame mounted chain hanger would be about 28-3/8 inches, so it'll just fit in the 2-3/4 inch space you have available. The system is designed for trailers with a loaded and ready to tow tongue weight below 600 lbs. The trailer ball is not included, for a 2-5/16 inch ball, you'll need # 19286 or # A-90 for a 2 inch ball. view full answer...
Hey Cory!
Yes, the Global Link RV Baggage Door Slam Latch # 295-000015 will fit with a 1-1/4" thick door. If you don't have a mounting plate then you'll also need the part # 295-000016 to complete the installation. view full answer...
Go To Results