Expert Answers about Nissan Rogue

• How to Connect RV Oval Porch and Utility Light to a Trailer Battery
• On porch light # RVPL7C the white wire is the ground and will need to attach to a clean metal surface. The black wire is the power wire. You can use some automotive wire to go from the light to the battery. Once at the battery you could use something like the battery terminal # DW05312. There are a couple of studs on this terminal and you could place a ring terminal on the end of the wire, remove a stud, then put the wire over the stud and thread it back into place. If your battery already...
  view full answer...


• Are Underbody Panels Required to be Removed to Install the Curt Hitch # C13168
• You would not be able to tell that the underbody panels have been removed on your 2014 Nissan Rouge unless you were under the vehicle. There are two pieces that will need to be removed. Check out the picture I attached to see the two pieces that get removed. All the necessary hardware to install this hitch is included. I also attached a link to installation instructions for you to check out also.
  view full answer...


• Wiring Harness for 2018 Nissan Rogue and Running a Wire to the Battery
• On your 2018 Nissan Rogue, the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # HM11143645 has a wire that runs to the battery for 2 reasons. The first and main reason is that there is no other source of constant 12v power in the rear of your Nissan. The second is that the powered converter that comes with the wiring harness is designed to reduce strain on your wiring system. This requires it to have a direct power source. If you were to tap into another...
  view full answer...


• Can the Swagman X Storage Rack Part # S80940 Be Used on Concrete
• Yes, you can install the Swagman X Mount Bike Carrier Storage Rack part # S80940 into the cinder block walls in your garage. However, I recommend heading to your local hardware store and picking up some concrete anchor bolts to secure it. This bike mount has a 100 lb weight capacity and will be more than capable of handling the weight of the Kuat Transfer V2 Bike Platform Rack part # KU74FR which is (47 lbs). You could even leave one or two bikes installed so long as they do not exceed...
  view full answer...


• Does Installation of Hitch 75902 on 2018 Nissan Rogue Affect Rear Lift Gate Sensors
• When a hitch like # 75902 is installed on a vehicle that has multiple rear bumper lift gate sensors usually it is only the center one that might be affected by the presence of the hitch tube. In practical terms all this means is that the liftgate function will need to be activated via one of the other sensors on the bumper. So instead of triggering the lift function by waving your foot near the center sensor as we'd all typically do, you'll simply do this near one of the others. I know...
  view full answer...


• Does Draw Tite Hitch # 75902 Fit 2019 Nissan Rogue and Allow Liftgate Sensor Access
• The Draw-Tite Max-Frame Trailer Hitch Receiver # 75902 is a confirmed fit for your 2019 Nissan Rogue. Based on its design, it will not change the tail gate lift sensor. You will still be able to utilize that feature to the left or right of the center receiver tube.
  view full answer...


• How to Extend Brake Output Wire When Flipping Axles
• There are not any extension cords with pre wired fitting that you can install on the brake output wire of your trailer when you flip the axle. However, this is not really needed as all you would need to do is cut the wire in half around 6" or so away from the braking assembly and then extend it out with part # 10-1-1 (per foot). In order to attach the new extended wire you can use the wire butt connectors, part # DW05745-10. These butt connectors have a heat shrink housing which is going...
  view full answer...


• Wiring Harness Troubleshooting For 2018 Nissan Rogue
• It is very odd that only the third brake light on your Rogue would be acting up after installing the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118480; it really should not be possible that only the third brake light is having an issue. I contacted the manufacturer about this and was told they have never heard of anything like this happening. They recommended disconnecting the negative terminal of the battery for about 5 minutes to reset any module that could have...
  view full answer...


• Will the etrailer Trailer Hitch Receiver Interfere With Hands Free Lift Gate on 2021 Nissan Rogue
• Installation of the etrailer Trailer Hitch Receiver # e93ZR may limit the functionality of the hands free sensor on your 2021 Nissan Rogue but the feature will not be lost. This will be the case for any hitch installed on your vehicle. Once installed, you will need to place your foot on either side of the receiver tube to activate it.
  view full answer...


• Installation Video for a 2013 Nissan Rogue Installing Draw-Tite Hitch 36542
• I was able to look up your order and see that you purchased the Draw-Tite Class II 1-1/4 inch Trailer Hitch Receiver # 36542 for your 2013 Nissan Rogue. The installation video that we currently have, which is linked to this answer, is on a 2016 Nissan Rogue.
  view full answer...


• How to Install a 7-Way Wiring Adapter on a 2015 Nissan Rogue
• The first step that you will need to take is installing a 4-Pole connector on your 2015 Nissan Rogue. I recommend using the Tekonsha T-One Vehicle Wiring Harness, part # 118480, this wiring harness will simply install behind the tails lights of your Rogue. The next step that you will need to take is to install the Universal Installation Kit, part # ETBC7, which then will provide you with a 7-Way the rear of your Rogue. If you do not already have a ball mount and hitch ball, I have attached...
  view full answer...


• Installation Process for Trailer Light Wiring on 2021 Nissan Rogue
• The 2021 Nissan Rogue is a vehicle that we have not had the opportunity to install a wiring harness on as of yet. This means, of course, that we do not have an installation video available. That being said, installation of a wiring harness like the Tekonsha T-One Vehicle Wiring Harness # TK76FR is fairly simple. The T-One connector plugs into connection points in the rear cargo area. Once that is done, a hot lead will run to the car battery. I would recommend the Tekonsha you looked at...
  view full answer...


• Do Appearance Panels Get Re-Installed on 2017 Nissan Rogue When Putting On etrailer Trailer Hitch
• The plastic parts are just "appearance" panels, and won't be re-installed after putting the etrailer.com Trailer Hitch # E98846 on your 2017 Nissan Rogue. These panels do not serve any specific function for your Rogue and as such can be put aside after installing the hitch. As you can see from the accompanying photo of the hitch installed on a '17 Rogue, they don't won't affect the overall appearance of your car (save for someone going underneath it). If you plan on using this hitch for...
  view full answer...


• Is The Process To Install a Transmission Cooler On a 2011 Nissan Rogue Different Than a 2010 Model
• The 2010 Nissan Rogue and 2011 Nissan Rogue are both the same generation (First Generation), therefore the process to install a transmission cooler should be the same because they also have the same L4 2.4L engine and CVT transmission combo. Unfortunately, we have not yet had a chance to install a transmission cooler on both models, only the 2011 model which you can see in the attached video so I would not have any exact advice for you. I did however look up the factory cooler removal...
  view full answer...


• How Long Can the Superwinch # 1450200 Run Before Needing to Cool Off
• I checked with Superwinch and for the winch part # SW1145220 they state Remember, the winch is for intermittent use only. During long or heavy pulls the motor will get hot. For pulling at rated capacity, allow motor to cool after 20 seconds of “On” time. At loads less than 50% of rated capacity, allow to cool after 2 minutes of “On” time. KEEP THE ENGINE RUNNING TO RECHARGE THE BATTERY during this break.
  view full answer...


• Can 12V Outlet In Rear Of 2014 Nissan Rogue Be Used For Wiring Harness Power
• We do not recommend using the 12 volt power outlet in the rear area of your 2014 Nissan Rogue when connecting a circuit protected wiring harness like part # C56033 because it has a higher rated fused circuit that could allow more power to be drawn through the wiring harness and potentially damage either the harness or the vehicle. This harness has not been tested with the installation using the rear power source and could void the warranty. I have attached a link to an installation video...
  view full answer...


• Are Load Resistors Needed on a 2010 Nissan Rouge when Installing LED Blinkers
• Yes, you will need a Load Resistor, item # DI34ZR, at at least two lights that you plan to install on your 2010 Nissan Rouge, if after installing the LED blinkers you have a hyperflash situation. If you still have hyper flash with two resistors installed you will need to install 2 more resistors at the other lights. You should install the LED blinkers first to determine if the resistors are required on your vehicle. You will not need to calculate the Ohms, the resistor is built to build...
  view full answer...


• Power Wire Has to be Connected to Battery for Trailer Wiring Harness # 118480, 2010 Nissan Rogue
• To install the Tow Ready Custom Fit Vehicle Wiring, # 118480, on your 2010 Nissan Rogue, you will need to route a wire from the red wire on the harness, under the vehicle (avoiding areas that may pinch or burn the wire), and to the positive battery terminal via the included in-line fuse holder and fuse. There will also be connections made at each of the taillights. I have included a link to the installation details and an installation video that will show how to perform this installation.
  view full answer...


• Remote Start Feature on etrailer 3,200-Watt Portable Generator
• You will only need to complete this step during the initial setup of the etrailer 3,200-Watt Portable Inverter Generator # 333-0003 and during situations where you need to choke start the generator. Since this way of starting requires operation from the control panel on the generator, you won't be able to use the remote in these instances. In most cases, after unpacking at your camp site and the initial startup, you will be able to start the generator using the remote control without issue...
  view full answer...


• How to Find Out the Cost of Installing a Trailer Hitch
• A professional could install trailer hitch # 75902 for your 2013 Nissan Rogue in about an hour or so. You would have to check local shops in your area to determine what rate they charge per hour. You can even print out the instructions which I have linked for you and take it to shops to see what they would charge you.
  view full answer...