Expert Answers about Keystone
- Replacement Brake Drum Hub Assembly For Dexter D44 4,400LB Axle
- Your Dexter D44 Axle number 635096 uses the Trailer Hub and Drum Assembly # 8-407-5UC3-EZ that comes preloaded with the Races # LM67010 and # L68111. It does include the Bearings # L68149 and # LM67048, Grease Seal # 58846, Grease Cap # 21-42-1 and lug nuts.
The Brake Assemblies # K23-462-463-00 that came with your axle can be upgraded to the Dexter Nev-R-Adjust Electric Trailer Brake Kit # K23-478-479 to reduce the maintenance as well as improve braking and extend the life of your brake...
view full answer... - Replacement Brake Assemblies and Bearing Kit for a 2012 Keystone Outback RS250
- The correct Nev-R-Adjust brakes for your 2012 Keystone Outback RS250 are the Dexter item # 23-468-469.
view full answer... - Recommended Self Adjusting Brakes for Al-Ko 4,400 lb Axles
- Michael, so you are correct you do have 4,400 lb axles so you can use the Dexter Nev-R-Adjust Electric Trailer Brakes # K23-478-479 for replacements.
These are self adjusting so you never need to manually adjust them, works with 14", 14 1/2", and 15" wheels, and includes both the left and right hand side.
For hubs we have had customers in the past use # 8-201-5UC3, but you'll want to check your existing bearings and verify that they will work with this hub.
view full answer... - How to Convert From Drum to Disc Brakes on Keystone Travel Trailer
- Okay, so there's a number of things you'll need to convert your Keystone travel trailer from drum to disc brakes, and I'll detail how to determine that. You'll need a hub and rotor disc brake kit, though we don't have a way of knowing specifically what hub you have. This means you will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them.
If you are unable to find them,...
view full answer... - What Is The Weight Of The MORryde StepAbove And Flip Tread RV Steps?
- The MORryde StepAbove RV Steps # MR85RR weighs about 70 lbs. As far as the flip step, I assume you are referring to the MORryde Flip Tread RV Steps # MR42UR which weighs about 45 lbs. Both of these steps will fit your 28" wide door. Personally I like the MORryde StepAbove RV Steps just because of how stable they are. There is no movement or bouncing when you use the steps like a lot of other RV steps. They are a bit heavier than others but they are really not difficult to open and close,...
view full answer... - Troubleshooting Landing Gear Fuse Blowing On a 2009 Keystone Montana
- Most often we find that a short has developed in the wiring which is usually caused from the trailer moving down the road over the years. You will want to start by tracing as much wiring as you can to look for anywhere the wiring may be damaged. You can verify the motor draw by using leads directly to a battery and an amp meter. If you do not have these tools most automotive repair shops can easily run the test which will let you know if the motor is bad.
view full answer... - 16'1" Replacement Awning Fabrics With a Black Weather Strip When Rolled Up
- The only Silver Fabric # LCV000334413 we have is going to fade to a white weather strip. The Sand # LCV000334407 you found, Black # LCV000334409 and Black Fade # LCV000334405 are our only fabrics that when rolled up would be black.
view full answer... - Will Lippert Ground Control 3.0 Fit 2013 Keystone Raptor 300MP
- Hey Brett, I checked out the specs of your 2013 Keystone Raptor 300MP and the Lippert Ground Control 3.0 part # LC675817 will work great for you. This will make leveling and stabilizing your RV pretty easy!
view full answer... - Troubleshooting Tekonsha Prodigy P2 Brake Controller Numbers Jumping When Pressing Brakes
- It sounds like the inertia sensor inside the Prodigy P2 # 90885 may have gone bad. If you feel like the brake signal may not be getting to the controller or may be intermittent you can use a Test Light # PTW2993 to verify the power is getting to the controller.
view full answer... - Finding Pin Box To Gooseneck Hitch Adapter For a 2010 Keystone Cougar 326MKS
- To give you the correct selection to choose from I have to know what pin box you have on your 2010 Keystone Cougar 326MKS. This is needed as not every RV is going to always have the same components even if they were built the same day in the same factory. I do know the 1621 was the most commonly used around this time so if you can either provide me with the Lippert tag information on the mounting arms above your pin box I can verify the bolt pattern for the pin box. Otherwise I would need...
view full answer... - Troubleshooting Single Brake Drum Overheating After Replacing Brakes
- I would not try to back that off since it is extremely hard to do on self-adjusting brakes. Also, I doubt the brake assembly overadjusted. You can spin it to see if there is excess drag compared to the others but I'm willing to bet the castle nut is overtightened on that hub. This is a common cause for overheating and seems likely based on the work that was recently done. The castle nut should be hand tightened then backed off a quarter turn.
view full answer... - Availability of 50 Amp to 30 Amp Adapter With Twist Lock
- The Camco Power Grip 90-Degree Locking Electrical Adapter # CAM55582 is exactly what you're looking for. This has a 50 amp female plug with the twist lock and a 30 amp male on the other end.
view full answer... - Will the Trailair Air Ride 5th Wheel Pin Box Replace Current Pin Box on a 2018 Keystone Cougar
- That's going to depend entirely off of your current pin box, JD. The Trailair Air Ride 5th Wheel Pin Box # LC155943 is designed to replace Lippert 1116 pin boxes so if that' what you have then it'll work.
If you're not sure what you have, then I recommend checking the pin box for some ID and see if it says what you have. If you're unsure and there are no identifying marks, then I'd suggest checking out the FAQ I've linked which shows you how you can measure your pin box to find out what...
view full answer... - Where is Kenda 225/75R15 Trailer Tire Made
- The Karrier ST225/75R15 Radial Trailer Tire # AM10256 is made in China, as with nearly every trailer tire, honestly.
I have added a link to our selection of 15 inch wheels for you if you need one to go with this tire.
view full answer... - Solution for Dometic 310 Toilet with Damaged Foot Pedal
- Hey Sandra so we've actually checked with Dometic in the past about seeing if they have replacement foot pedals for the 310 and they do not have that as a replaceable part. Only solution would be to replace the toiled or modify what you have now to get rid of the sharp edges like with a file or sandpaper.
If you're good with replacing the whole assembly then we have the Dometic 310 toilet available in Tan Ceramic # DOM37FR and White Ceramic # DOM57FR.
view full answer... - Availability Of Dexter Bearing Kit K71-718-00 Or Equivelant Components.
- Hey David, so we do have a potential solution for you, but we do not carry the exact Dexter Bearing Kit K71-718-00 that you are looking for. We do carry all of the components of this kit individually though, and I have listed all of the components below:
- Grease Seal # RG06-050
- Cotter Pin # 165649
- Outer Race # LM67010
- Outer Bearing # LM67048
- Inner Race # L68111
- Inner Bearing # L68149
view full answer... - How to Tell if Lippert Thin Shade Window Kit Will Fit a 2021 Keystone Springdale Travel Trailer
- The Lippert Thin Shade Complete Window Kit # LC806621 fits 1-1/2" to 2" thick doors and installs in a 15" wide x 24" tall cutout. If that's what your Springdale trailer has then this will fit.
Unfortunately I don't have the specs for what came on your trailer so I don't know right off-hand if this will work or not.
view full answer... - Replacement Vinyl Insert Trim Needed For a 2022 Keystone Cougar 22RBS
- Based on your measurements it sounds like you need the 1" Vinyl Insert Trim # 37210015 with a channel opening 5/8" wide. We have no way to look up your parts from Keystone for your 2022 Cougar 22RBS so we have to go off the measurements you provide.
Insert trims are offered in the 1" width above or a 3/4" # 37211235 Since the trims need to bulge out once inserted we know the 3/4" is to narrow for the 5/8" opening since there are slots it needs to fit into.
view full answer... - Can a WDS Without the Sway Control Ball Hole Have One Added
- If the head on your WDS does not have a hole for a sway control ball, then I recommend just returning the system and getting a new system that does have sway control, like the Reese Strait-Line Weight Distribution System # RP66084.
The Strait-Line systems use dual cam sway control, which prevents trailer sway before it begins, has a tongue weight range of 600-1,200 lbs, a gross towing weight capacity of 12,000 lbs, and is one of the top sway control systems on the market.
view full answer... - Replacement Shroud for Dometic Duo-Therm AC on 2010 Keystone Bullet
- The 3107541.009 is the part number for the analog control kit for the Dometic Duo-Therm on your 2010 Keystone Bullet. Based on the information we have it does appear as though the # DMC69FR you looked at is the correct replacement. However, without the actual AC model number we can't be sure. I understand it is covered right now but I recommend measuring to confirm this. The shroud measures 34-1/2" long x 30" wide x 10-3/4" tall.
view full answer...
Go To Results