The Westin Oval Tube Steps w/ Custom Installation Kit part # 22-5050-1635 will fit a 2006 - 2010 Hummer H3 but that's all. However, there are different install kits which allow you to use them on other vehicles as well. view full answer...
Yes, the Trailair Flex Air 5th Wheel Pin Box part # LC369535 which is rated for 21,000 lbs will work just fine on a trailer with Lippert 1621 Pin Box and 18,000 lb gross vehicle weight rating (GVWR). The gross vehicle weight rating is the most the trailer can weigh fully loaded so you will never exceed the weight capacity of the pin box and even have a few thousand lbs of wiggle room. view full answer...
According to the Thule Fit Guide, the Thlue Flat Top Ski and Snowboard Carrier, part # TH7326 should fit just fine onto the factory cross bars. I have added a link to the installation instructions below. If your cross bars measure 2 inches by 4 inches, the THXADAPT7 bolt kit will probably be needed. view full answer...
There is a good possibility that the Swagman Trailhead, # S63360, will clear the spare tire on your 2007 Hummer H3 as this rack has a fair amount of clearance. From the center of the hitch pin hole to the back of the upright bar, the distance is 14-1/2 inches.
You will need to measure the distance from the center of the hitch pin hole on your H3 out to the distance required to clear the spare tire. If this distance is less than 14-1/2 inches, the rack will fit. I have included a link... view full answer...
To install a platform rack on your 2003 Hummer H2 we first need a roof rack and for that I recommend the Yakima JetStream system that includes the following parts:
- 60" JetStream Crossbars # Y00426
- SkyLine Towers # Y53TR
- Landing Pad 4 # Y00224
This installs directly to the fixed mounting points on your Hummer which then allows you to use the Rhino-Rack Pioneer Platform Tray # RR82TB along with 2 of the Mounting Kit # RR43105 to get it installed.
The Pioneer Platform # RR85ZW... view full answer...
Judging by the sticker on your bars it does look like those are the factory bars. The Aries Round Nerf Bars # AA204075-2 will fit on your 2007 Hummer H2 just fine in place of the OEM bars. If you'd rather have the black bars then you'd need part # AA204075 instead.
If you're looking for replacement hardware you'll need to get that from General Motors as hardware will need to be a direct replacement. Nerf bars can use specific hardware per each manufacturer which is why it needs to be a... view full answer...
There is no cutting or trimming of the bumper on the Hummer H3 when installing the Draw-Tite Class III Trailer Hitch, # 75382. The installation on your Hummer H3 is a very simple bolt-on application. The hardest part might be lowering the exhaust for ease of installation.
I am sending a link to the installation instructions for the Draw-Tite Class III Trailer Hitch, # 75382.
If you will be towing, you will need the Curt Ball Mount, # C45010, and the Pin and Clip, # PC3. You will also... view full answer...
The item you selected, Thule Roof-Mounted Bike Carrier, part # TH859XT is designed to work with round, square, aero, elliptical, and most factory crossbars so it could work on your Hummer.
A Roof Mounted Bike Carrier I would recommend that would work with your Hummer, is the Fork Style Roof Mounted Bike Rack, part # S64710 . This bike carrier fits factory cross bars and will work great on your 2006 Hummer H3 with roof rack rail cross bars. Part # S64710, is similar to the Rola Roof-Mounted... view full answer...
The Thule Tepui Explorer Autana 3 Rooftop Tent with Annex # TH8001ASK05 does have a few requirements to fit on your 2006 Hummer H3:
You'll need crossbars that are spaced 32" apart with a 33.5" railing distance (pictured below).
They'll need to have a minimum weight capacity of 165lbs.
They'll need to be within a maximum width of 3.25" and height of 1.5".
If your crossbars sit on raised rails then the rails will need to have supports in between the ends as well to handle to weight.
If... view full answer...
Bar style friction sway control units such as # 83660 are not trailer or vehicle specific. On the trailer, the side of the frame will need to be clear 21 through 27 inches back from the center of the ball cavity of the trailer coupler. The bracket that mounts on the trailer end is 3 inches tall.
On the vehicle side you will need to use bracket # RP26003 with a ball mount. The friction sway control bar comes with everything else you will need. view full answer...
The SportRack Hitch and Cable Lock you referred to, part # A32022 isn't completely compatible with the SportRack Ridge Swing # SR2415 bike rack. The anti-rattle hitch portion of the lock will indeed work with the rack, but the cable lock portion is not compatible.
You can purchase the anti-rattle lock portion by itself as part # SR0901. If you were needing a cable lock, the etrailer brand # e98891 would be a good choice. view full answer...
Yes, the Tekonsha Wire Replacement for GM Vehicles, part # 3015-P,and the Tekonsha Prodigy P2 Proportional Brake Controller, will work on 2003-2007 Hummer H2, so it would work on your vehicle.
Even though the title says it will fit 2003-2006 GM vehicles there are a few 2007 GM vehicles, such as the Hummer H2 and the 2007 classic body style GM trucks, that it will work on.
I included a video below of the brake controller and wiring harness being installed on a similar 2007 vehicle as... view full answer...
As long as the vehicle is a 1996 model or newer equipped with an OBD-II port, you will be able to connect the Edge Insight CTS, # EP84130.
The Insight is not a tuner type of programmer. It can display several parameters and allows you to monitor them but you cannot tune the engine with it. It will not add horsepower, torque, or change any of the factory settings.
Some of the parameters you can monitor are:
Battery Voltage
Intake Air Temperature (IAT)
Engine Oil Pressure (EOP)
Engine... view full answer...
Yes, the Yakima MegaWarrior Extra Large Roof Rack Cargo Basket part # Y07080 will mount to the factory crossbars you have on your 2009 Hummer H3 Alpha without additional purchase necessary. We have not yet installed this cargo basket on a Hummer H3 so I would not be able to confirm if it covers the sunroof but if the sunroof is positioned between the two crossbars then you can assume it will cover it. It is also not recommend to open the sunroof with the basket attached as the noise would... view full answer...
So first, your 2004 Hummer H2 does have to be stock to use the Superchips Flashpaq F5 Performance Tuner - GM - Gas/Diesel # SU2845.
If yours isn't, you'll need to take it to a GM dealer to have them return it to stock. As for returns, once something is used, it cannot b returned. And insofar as if the # SU2845 will be beneficial to your '04 Hummer, yes, it absolutely will.
It has numerous tunes, including performance, that allow you to get the most out of your Hummer. view full answer...
We have not yet tested the Curt Roof Mounted Cargo Basket part # C18115-117 on a 2006 Hummer H2 with a factory roof rack therefore, in order to determine compatibility you would need to do a bit of measuring on your Hummer. For starters, the Curt cargo basket works with crossbars that are spaced between 22 and 50 inches apart on center and do not exceed 3" wide x 1-5/8" tall. Therefore, as long as the factory roof rack on your H2 fits these two criteria then it will work well for you. Unfortunately,... view full answer...
If the hitch on your 2007 H2 is a 2-inch size then you can use an adapter/extender like the Curt Hitch Extender # C45796. However, you need to be aware that use of any extender will reduce your hitch's tongue weight and towing weight ratings by 50-percent.
This loss of hitch capacity results from the change in the geometry of the forces on the hitch. In the same way that slipping a length of pipe over a tire iron gives you more leverage to loosen a stubborn lug nut, using an extender... view full answer...
I checked with Timbren and they have confirmed that the Timbren Rear Suspension Enhancement System # TGMRH2 that you referenced is compatible with your 2005 Hummer H2 with auto-leveling air ride suspension.
I attached installation instructions and an FAQ on Timbrens for you to check out. view full answer...
We do have a fit for your 2007 Hummer H3, but the CIPA Custom Towing Mirror - Slip On - Driver Side # CM11551 wil not fit. They actually only fit 2015-2019 Ford F-150.
The towing mirrors I recommend are the CIPA Universal Towing Mirrors - Clamp On - Qty 2 # CM11980-2. These mirrors easily clamp onto your existing mirrors and are a fit for your 2007 Hummer H3. Another reason I recommend these is that they pivot 360 degrees to give you the view you need at all times. view full answer...
Go To Results