The easiest way to pick out replacement landing gear sets is to go by the distance between the brackets either on the trailer or on the legs themselves so that you can pick out a set that will match up to the trailer without needing modifications.
Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you,... view full answer...
It is always best to install any Weight Distribution Hitch # EQ37100ET on flat ground to ensure you have the trailer level and bars set to the correct amount of tension. This will help you to ensure it is set correctly and will not damage the hitch. Once you know the system is set correctly on flat ground it is recommended to remove the spring bars when transitioning from the street onto a steep driveway. This is necessary to ensure the bars or L-brackets do not become damage due to the... view full answer...
The inside dimensions of the MORryde RV Cargo Sliding Tray # MR47FR is 58-1/4" long x 22-7/8" wide.
Additionally, this unit has overall dimensions of 60" long x 26" wide x 6-5/8" tall, has a maximum weight capacity of 800-lbs, and will work with RV cargo compartments that are at least 60" deep.
Attached is a product review video for you to check out if you haven't already. view full answer...
I spoke with my contact at Lippert and this is what they sent me about the external sensor issue you have:
External sensor error means there is an issue with the rear leveling sensor. This will be located 2-3 foot behind the rearmost axle. There may be an access panel in the underbelly, or there may not. Typically this error is due to a bad connection to the sensor.
It is important that once the error code has been resolved, the user of the unit must manually retract all jacks completely... view full answer...
I spoke with Everchill and I was able to confirm with them that there is no replacement parts available for the:
-Everchill RV Wine Cooler # 324-000113, unfortunately.
With that being said, the only option for you is to replace the entire unit with # 324-000113. I know it's not an ideal situation but as I've confirmed with the manufacturer this is going to be the only option for you. view full answer...
The correct braking assemblies for your 2016 Crossroads Sunset Trail Super Lite 15 250RB are going to be dependent on the size of your drums.
Since your trailer has a GVWR of 7582 and tandem axles it more than likely uses 10" brake assemblies which are the Dexter # 23-468-469 or the etrailer # AKEBRK-35-SA. You can confirm this by measuring the diameter and depth of your drums following the included diagram.
Neither kit comes with new mounting hardware so if your current hardware is in... view full answer...
I looked up the owners manual for your truck and your maximum trailer weight capacity is 9,200 lbs and your GCWR is 15,000 lbs.
Timbrens # TGMRCK15S are designed to help support the rear of the vehicle when towing a trailer. They essentially stop the vehicle from sagging too far in the rear. I recommend getting a weight distribution hitch that pairs well with the travel trailer that you decide on. We have many to choose from that will help with sagging and sway control.
I have provided... view full answer...
If I were adding a second AC unit to a travel trailer, such as the 2019 CrossRoads Zinger Travel Trailer, I would select a unit that has a start capacitor installed and comes with an air distribution containing the controls such as the Advent Air RV Air Conditioner w/ Air Distribution Box and Start Capacitor, # ACM135C. The included air distribution box has a built-in thermostat that lets you set the fan speed and temperature. The included start capacitor will help jumpstart the AC. This... view full answer...
The diameter of your 205/75B14 tire is 26.1", and has a width of 8.1".
If you are needing a replacement tire I recommend the # AM1ST86 if you only want to replace one tire, or the # AM10235 if you are ok with replacing both tires.
The reason for this is the # AM1ST86 is a bias ply tire like your current tire, which you can tell by the B in the size between 75 and 14, where the # AM10235 is a radial tire. Radial and bias ply tires have a different sidewall construction making them not... view full answer...
Yes, the LaSalle Bristol RV Kitchen Sink Drain w/ Strainer Basket # 34465JN10081 does fit the Patrick Distribution Bowl Stainless Steel RV Kitchen Sink # 277-000089 that you also referenced. view full answer...
You will need to use the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks # RM-2460-2580 for upgrading the suspension on your 2019 Crossroads Redwood 3951WB Fifth Wheel Camper. This kit is rated for your 8,000lb axle and the springs have the same capacity as your factory springs.
The Timbren Silent Ride Suspension for Tandem Axle Trailers # TSR14K35T01 while capable of mounting your 8,000lb axle the springs only have a 14,000lb total capacity. Your Redwood needs the 16,000lbs... view full answer...
The inside surface of the Adco RV Dual Propane Tank Cover # 290-2713 is a smooth fabric material fairly similar to fleece. The exterior vinyl surface has an embossed diamond plate texture and the bottom of the cover has an elastic hem for a secure fit around your dual 30-lb tanks. view full answer...
For the broken brake assembly the TruRyde kit part # TRU36FR would be your best option for a self adjusting brake set that comes with a replacement left and right hand side assembly. Then for replacement hub/drums you'd want the part # AKHD-545-35-EZ-K which comes with new bearings and seals. view full answer...
The 94720 Reese Goose Box is a fit for 1621, 1621HD, and 0719 bolt patterns so you most likely have a 1621 bolt pattern. That being said, it's still best to measure to confirm the pattern. I've attached a link below that will walk you through measuring for the bolt pattern.
For a standard 1621 pin box you can use the Lippert 1621 5th Wheel Pin Box # LC1191191. I do recommend going with an upgraded option like the MORryde Cushioned 5th Wheel Pin Box for 11.5K to 14K Trailers w/ Lippert... view full answer...
If your springs are essentially sitting totally flat they've stretched as far as possible basically. The best option we have would be the 3,500 lb leaf springs part # e54SR that you referenced. These are the right capacity and shorter than your stretched springs by enough that they would fit well. view full answer...
If the actual leg of the stabilizer jack, like the Lippert High-Speed Power Stabilizer Jack # LC298707, is bent then you'll unfortunately have to replace the entire assembly. Lippert has a few replacement parts for this jack but I think the mentality behind not having a replacement for the leg is that if there was an impact powerful enough to bend one of the legs then the frame of the unit is likely messed up as well so you'll want to replace the whole thing from the safety viewpoint.
Attached... view full answer...
There is a folding double step that has the same 24-1/4 inch wide x 8-1/4 inch dimensions as the Lippert Manual Pull-Out Step for RVs - Single # LC432678; the step you are looking for is the following:
- Lippert Manual Pull-Out Step for RVs - Double # LC432682
I have added a link below to a video review for you to check out as well if you'd like to take a look. view full answer...
For the Reese/Pro Series 15k fifth wheel hitch you have the way to order replacement pins for the head of the hitch is with the part # 30583 which does come with additional hardware but it's only way to get just the pins. view full answer...
The LaSalle Bristol Pop Up Drain for RV Bathroom Sinks # 34465WPR1303 will work great for your Better Bath Single Bowl RV Bathroom Sink # LC209635. view full answer...
For your 2015 Crossroads Carriage 40RE 5th wheel camper with a flange to flange measurement of 13' 4"(160"), you will want the Solera RV Slide-Out Awning White # LCV000163301. The flange to flange is the widest points on the slide on the outside of your camper. This slide topper uses a fabric that is 13' 7"(163") wide and the hardware will stick out another 2-1/2" on each side. The information I am providing you is directly from the Solera guide for selecting the correct topper. I do know... view full answer...
Go To Results