Inside Material on Adco RV Dual Propane Tank Cover 290-2713

Question

Question:

What material is used in the inside?

asked by: Gary

1

Helpful Expert Reply:

The inside surface of the Adco RV Dual Propane Tank Cover # 290-2713 is a smooth fabric material fairly similar to fleece. The exterior vinyl surface has an embossed diamond plate texture and the bottom of the cover has an elastic hem for a secure fit around your dual 30-lb tanks.

expert reply by: Adam R

1

click to enlarge

Answer 1

That is odd but you are correct. The dimensions of the #290-2713 match 20 lb tank dimensions and then the 40 lb tank version part #290-2714 that you referenced is correct for your 30 lb tank.

view full answer...

Answer 2

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 4

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

Based on the parts diagram from Winnebago your 2013 Itasca Suncruiser 32H will use the Lippert Replacement 500:1 Motor for Electric In-Wall RV Slide-Out System #LC287298.

view full answer...

Answer 7

The piece you're referring to in the #LC26VR kit is called a "shoe". This part is plastic with foam pads on each end that helps cushion the motor bracket as it slides back and forth to either end of the track.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 10

The Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV Leveling System part #LC421484 replaced the LC234802. It may look a bit different but it will still work great in its place.

view full answer...

Answer 11

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 12

Hey David, thanks for the picture. I was able to track down a spec sheet for your Dexter axle which I have included below. The 031-029-02 bearing is item #15123 and the 031-030-02 bearing is item #25580. For a bearing kit you can use part #BK3-110…

view full answer...

Inside Material on Adco RV Dual Propane Tank Cover 290-2713

Product Page this Question was Asked From

Continue Researching