The Electric Motor # LG-142178 will work with the Gearbox # LC276602 which is compatible with most 5th wheel landing gear sets on the market. Unless you have a really oddball landing gear set you'll be good to go. If you are unsure about what you have just send me some photos and I can take a look for you.
I've attached a video showing the motor being installed that you can compare with what you have. view full answer...
To find out if the Lippert Components 32" Lead, part # LC179013, will work with your 5th wheel, you need to check your current one against this one to see if it matches. Key measurements of this leg are:
Bracket Stop - 17-1/2"
Height with one hole out for foot plate attachment - 32"
Capacity - Manual (4000 lbs), Single Motor (2500 lbs), and Dual Motor (4000 lbs)
Travel Distance: 21"
Drop Leg Travel: 16"
I've linked to a video below that will help you find out how to measure these.
Finally,... view full answer...
The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC675817 runs off of your trailer's battery (DC) and not off your your trailer AC electrical system (30 amp). It requires a minimum of 12.75V DC from the battery for proper operation.
Each motor can operate independently in manual mode or together auto mode. The motors run to a controller which is wired to the battery with a 50 amp circuit breaker.
This system is a universal fit designed for trailers with a GVWR up... view full answer...
The M-9000-PK part number you have means you have a Venture motor. Typically this will be rated to 5,000 pounds and do wear out over time as well. With that being said, the Heavy Duty 6500-pound rated Tuson Landing Gear Motor # LC196308 should get you up and running better. The motors for these are pretty universal and I have confirmed this will replace your current motor a few times, so I can definitely recommend it as a good replacement. view full answer...
You will need to use the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks # RM-2460-2580 for upgrading the suspension on your 2019 Crossroads Redwood 3951WB Fifth Wheel Camper. This kit is rated for your 8,000lb axle and the springs have the same capacity as your factory springs.
The Timbren Silent Ride Suspension for Tandem Axle Trailers # TSR14K35T01 while capable of mounting your 8,000lb axle the springs only have a 14,000lb total capacity. Your Redwood needs the 16,000lbs... view full answer...
We do have a cover that will fit your Crossroads Sunset Trail 210FK travel trailer, though all covers may be a bit baggy at the top for trailers that have a sloped front end. However, the best option for a cover, the Adco Tyvek All-Climate + Wind RV Cover does have cinch ropes and weighted buckle straps which are going to ensure the tightest overall fit. The correct option is the following:
- Adco SFS AquaShed Cover for Travel Trailer # 290-52242
The Adco cover is the one best designed... view full answer...
No, unfortunately the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide # C13704 will only fit RV's that have a frame width ranging from 22" to 66", and since you mentioned yours is 68" it's going to be a bit too small.
What you should've gone with instead is the Curt RV Bumper 2" Trailer Hitch Receiver # E-100. This hitch will mount directly to your bumper so there won't be any clearance issues from it sitting back too far, and it also has the same 3.5K weight capacity... view full answer...
I'm not sure what you mean by upgrade but we do have the correct replacement bearings for your trailer, the Bearing Kit part # BK3-200 which contains bearings, races, and seals. This is a direct match for the Lippert Bearing Kit 333951.
Please note, if you're having issues with your existing bearings then you should know that the main reason they fail is because of improper lubrication. Therefore, you'll need to make sure you repack them every year and add grease as needed. view full answer...
In order to correctly measure a hub/drum you'd need to do so on the inside, where the shoes ride. I have attached a photo below that shows this. The Trailer Hub and Drum Assembly part # AKHD-545-35-K for example measures 10" x 2-1/4".
I have attached all of our options below. view full answer...
The Solera awning fabric like the part # LCV000334438 that you referenced does only have the one bead but it would work fine on your roller that does have two slots. It would just install into one of the beads and you'd be set. view full answer...
The fit of RV steps such as the Lippert SolidStep units like # LC791572 depends on the size of your trailer door opening. This specific 3-step model fits RVs with a doorway that is 26 inches wide to 29-7/8 inches wide and a threshold height of 27- to 36-inches from the ground to the floor of the RV.
Part # LC791574 is a similar 4-step unit that fits a doorway width of 28-inches with a ground-to-threshold height range of 35- to 44-inches.
I checked the NADA guide for details on your travel... view full answer...
The dry weight I'm seeing for a 2018 CrossRoads Cruiser Aire Fifth Wheel trailer is roughly 8,000lbs so you'd be more than fine with the etrailer Landing Gear Set # RVLG-8000 you were looking at. Landing gears are only supporting a fraction of the weight we the majority of the weight resting on the axles/wheels of the trailer.
Another important aspect to consider is the weld stop measurements so that the installation can be a more direct replacement so you don't have to do any additional... view full answer...
Yes, the Global Link RV Entry Door Locking Latch Kit # 295-000021 that you referenced will replace the latch you sent in a picture of on your 2011 Crossroads Zinger. view full answer...
The Furrion RV Electric Fireplace # FF34SW15ABL will allow you to mount it in 2 different cutout sizes. The difference is if your cabinet is deep enough and if it is able to protrude from the cabinet surface.
With the cutout: 30-9/16" wide x 16-1/4" tall x 5" deep the fireplace will sit out from the cabinet 1-1/4". The instructions refer to this as Half-Flush, see link below.
The cutout: 33-3/16" wide x 17-13/16" tall x 7-3/16" deep will only only stick out the thickness of the front... view full answer...
I do have an option for you but the angle piece from the Swagman Traveler XCS S64664 would not allow you to carry a bike rack and cargo rack at the same time. If you were able to make it work it would be very unsafe.
I recommend to use the Malone Dual Hitch Extender for 2" Trailer Hitches part # MPG544 which will allow you to carry a cargo rack and bike rack at the same time. This extension measures 12" but will reduce your hitch's weight capacity by 50 percent. The weight of both racks,... view full answer...
The U-bolts that come with the CE Smith Post-Style Guide-Ons for Boat Trailers part # CE27646 are compatible with c channels like what you have on your trailer but they fit channels up to 4-1/4" tall. There is longer hardware available with part # CE11416 which fits channels up to 5-1/4" tall. That is the longest U-bolt hardware for the CE Smith Guide-ons available or any other Guide on at this time. view full answer...
It does appear that the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box # GY58GR is the correct one for your 2021 CrossRoads Volante 310BH. To ensure that there will be no issues installing this I recommend contacting your dealer to ensure it has the 1621 pin box from the factory.
Your Volante has a tongue weight of 1,644lbs dry so this fits into the 1,500-3,500lbs the hitch requires. With your 2018 Ram 3500 having the 8' bed you will not have any turning radius issues with... view full answer...
If you're looking to only replace the rooftop unit and still maintain use of the thermostat inside of your trailer then I recommend going with the Advent Air Replacement RV Air Conditioner for Dometic Setup w/ Start Capacitor - 15,000 Btu # ACDOM150 or # ACDOM150B for a black shroud. These units have the 15,000 BTU rating you're looking for and are a quick swap from your Dometic unit.
To remove your old unit you'll need to take off the cover for your air distribution box on the inside... view full answer...
Since you already have your leaf springs above the axle you cannot use an over-under kit like Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00. Instead, your only safe option is to use taller suspension hangers. I attached a link which shows the various sizes of hangers for trailers; you will want to match something up that fits your trailer and is slightly taller than your current hangers to gain the desired lift. view full answer...
No, the lid for the MaxxAir MaxxFan Mini Roof Vent w/ 12V Fan # MA00-04301M has to be closed while driving. The workaround to this is to install the MaxxAir FanMate RV and Trailer Roof Vent Cover # MA00-955001. This cover is designed specifically to fit over your vent to allow you to utilize your vent while traveling or in any inclement weather. It installs using EZClip pins that will simply slide through the four connection points already on your MaxxAir Vent. view full answer...
Go To Results