Don't worry, we can help you with this!
Anytime the trailer's fully loaded weight is greater than half the weight of the vehicle towing it, we recommend using weight distribution. Since a 2016 Chrysler T&C weighs about 4700 lbs, I would advise using a weight distribution hitch. A weight distributing hitch will increase the capacity of the hitch, but NOT that of the vehicle. In your case, you'll still be limited to the 3600 lb towing capacity of the vehicle, regardless of whether or not... view full answer...
According to my research your 2000 Chrysler Town and Country can be flat towed with all 4 wheels on the ground as long as you use a transmission lube pump from Remco Industries. We sell everything else you would need except for the lube pump.
First you will need base plates # 242-2. Then, for a compatible tow bar, you can use the Falcon 2 # RM-520. I have linked a video of this tow bar for you. You will also need safety cables # RM-643. The coiled design helps keep them off of the ground.
For... view full answer...
If your 2016 Chrysler Town and Country already has a 4-pole flat trailer connector installed (at the factory or by the dealer) then installation of the Prodigy P2 Brake Controller # 90885 will require only the # ETBC7 installation kit along with the controller. The linked video shows the complete install process in a similar vehicle and references the air bag at the 17:45 mark. An install article for the kit is linked as well. view full answer...
Just about everything you need is available in one kit. Take a look at the 4 and 7-Way installation kit # ETBC7. This kit provides a 7-Way (the existing 4-Way will just plug into the 4-Way receptacle on the adapter) and it comes with all the wiring and circuit breakers you will need to wire in the brake controller.
The only other parts you will need are a circuit tester like # PTW2992, and, if your brake controller doesn't have a wiring adapter, you will need # 20127 (for Tekonsha or... view full answer...
You can't go wrong with either of the brake controllers you mentioned. The main difference between the controllers is how user-friendly the display is. The Prodigy # 90885 P2 uses an digital display that will display error codes in the event of any problems with the trailer's braking system. The Prodigy # 90195 P3 has a more user friendly display, which will actually spell out any problems, rather than an error code that you'll need to go look up.
To install the brake controller, you'll... view full answer...
Thank you for providing the bearing numbers and other part numbers from the repair parts manual for your 1999 Coleman Grand Touring Series Santa Fe 3389 Pop-Up camper. Based on the bearings and bolt pattern for your existing idler hubs, we can determine the correct parts to add electric brakes to your trailer.
The components needed to add electric brakes to a trailer are an electric brake compatible hub and drum, brake assemblies, a brake mounting flange, trailer wiring, a breakaway kit,... view full answer...
To convert your 4-Way trailer connector you will need the Brake Controller 7 & 4 Way Installation Kit, item # ETBC7, which includes everything needed to upgrade your trailer connector to a 7-Way RV connection. We have detailed installation instructions for you to review, see link.
The one other thing you will need is a No-Drill Mount Bracket, # C57202 (long) , to attach the connector to the hitch. You will bolt the bracket included in the # ETBC7 wiring kit to this bracket and then attach... view full answer...
I recommend using the Curt # 13389 because of the quality of the powder coat on the Curt hitches compared to some of the other available hitches. This is a Class III hitch with a 2" receiver and is a confirmed fit on the 2007 Chrysler Town and Country models with the Stow-N-Go seats.
If you're going to be towing a small trailer with this hitch, you'll also need a wiring harness, ball mount and hitch ball. For a wiring harness I recommend using the Tekonsha T-One # 118300 because of the... view full answer...
Thanks for that photo, which shows you do have a 4-way like Wiring Harness # C56331 on your 2014 Chrysler Town and Country and we have exactly what you need in order to add a brake controller.
You will simply need to add the Universal Installation Kit for Trailer Brake Controller # ETBC7, which will give you a 7-way connector, circuit breakers and the rest of the hardware needed to install a brake controller. The 7-way will power your trailer's electric brakes as well as its lights.
For... view full answer...
Those are some extremely old tires. We recommend changing them every 6 years or so regardless of tread wear.
The metric size for your 20.5 x 8 - 10 tires is 205/65-10. Our most popular tire in this size is # AM1HP54. It has a load range D and max capacity of 1,330 pounds at 70 psi.
If you'd like a higher rated tire we have # AM1HP56 with an E load range rated for 1,650 pounds at 90 psi.
Both tires have a 2-year limited warranty. view full answer...
All you will need to adapt your Yakima Raptor bike rack to the crossbars on your 2013 Chrysler Town and Country are the universal MightyMounts, # Y03590. I have linked a video review of these for you. view full answer...
To replace the headlight bulbs on your 2014 Chrysler Town and Country you will choose a set of new type H11 bulbs. You only need two bulbs, not four. The linked page shows all bulbs of this type that are DOT-compliant (legal) for on-road use and these include the standard Halogen type like # VX-LH11, which is the item you referenced in your question. These are just like your factory bulbs.
If you would like bulbs that are still DOT-compliant but that are brighter than the factory bulbs... view full answer...
When installing The etrailer hitch # e98854 onto your 2016 Chrysler Town and Country it uses the existing M10 and M12 bolts that should be present on your vehicle. Since your hardware is missing you will need to contact your vehicle's dealership to get the correct hardware. If you buy standard hardware from a hardware store it will take away the warranty of your trailer hitch. The etrailer hitch in my opinion is the best hitch that we offer for your Chrysler Town and Country because it... view full answer...
You can flat tow your 2005 Chrysler Town and Country with automatic transmission behind your Class A motor home.
There are 5 components needed to flat tow a vehicle and those are a tow bar, base plate kit, safety cables, tow bar wiring and a supplemental braking system.
The Roadmaster MX Base Plate Kit, # 274-3, will work on your vehicle. You will also need a tow bar like the Roadmaster Falcon 2 Tow Bar, # RM-520.
We have two options for wiring/lights. You can use a diode wiring kit... view full answer...
To add electric brakes to your 1998 Coleman pop up camper you should be able to use the Electric Trailer Brake Kit - Self-Adjusting # AKEBRK-35-SA and then hub and drum assembly # AKHD-545-35-EZ-K for a 5 on 4-1/2". You just need to make sure that your current bearings are # L68149 and # L44649 plus verify that your grease seal has an inner diameter of 1.719". If you have something else please let me know and I can let you know what alternative parts you need.
You also need to add a 7-Way... view full answer...
As it sounds like you have a Curt Trailer Connector Adapter # C57672 on your 2013 Chrysler Town and Country you will need the Wiring Kit # 5506. This will contain the wiring, connectors and circuit breakers needed to power a brake controller as well as the charge line for the trailer breakaway battery. I recommend using the Redarc Tow-Pro Liberty Brake Controller # RED52VR. This brake controller uses a small dash mounted control knob to give it a clean look. The main unit will be hidden... view full answer...
Since you already have a 4 way flat on your 2010 Chrysler Town and Country, to add a 7 way connector you'll need to use the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires # ETBC7. This gives you all of the parts you'll need to install a 7 way on your 2010 Chrysler Town and Country and allow you to tow a trailer with brakes.
If you don't already have a brake controller, I recommend using the Tekonsha Prodigy P3 Trailer Brake Controller... view full answer...
We have just about everything you are going to need packaged in one kit. Take a look at the 4 and 7-Way installation kit # ETBC7. This kit is going to provide a 7-Way (the existing 4-Way will just plug into the 4-Way receptacle on the adapter) and it comes with all the wiring and circuit breakers you will need to wire in the brake controller.
The only other parts you will need are a circuit tester like # PTW2993 unless you already have one, the wiring harness for the controller, # 20127,... view full answer...
It looks like the hitches for the 2011 Chrysler Town and Country use the bolts that are already drilled into the vehicle.
I've linked to a video installation of the Draw-Tite Hitch, part # 75579, so you can see how it works.
As for the size of the bolts, looking at the installation instructions for this hitch (also linked below), it looks like they are a mix of M12 and M10 bolts. You can find these at your local hardware store. view full answer...
Go To Results