If you want a cover for your actual hitch ball itself you can use # 42250 or one of the others shown on the included link.
In the case of your 2007 Chrysler Aspen the only size of hitch receiver that is offered is the 2-inch Class III type; please see the linked page. Hitch BALLS can be a 1-7/8-inch diameter (or 2-inch or 2-5/16-inch) but a hitch receiver itself, which is mounted to a vehicle frame, will generally be either 1-1/4-inch, 2-inch or 2-1/2-inches square.
In your 2-inch hitch... view full answer...
Yes, I checked with Rhino Rack and the roof rack by them that consists of the Rhino-Rack Vortex Aero Crossbars # RRVA126B-2 and part # RRSX100 has been confirmed to fit your 2007 Chrysler Aspen and would work well for you.
These two parts are all that is needed to complete the roof rack for your vehicle. view full answer...
You might need a more efficient transmission cooler for optimum cooling on your 2007 Chrysler Aspen. Stacked plate coolers are the most efficient, such as # D52506. If the cooler you have now is an aftermarket external cooler then you likely won't need additional parts to run the lines to and from it but you will need hose barb fittings that can mate up with the cooler, # D98200. Or you could get a kit, # D13403, which has a smaller core but it is still Class V rated. view full answer...
The air lines of the Air Lift Load Controller Compressor System for Air Helper Springs # AL25856 are 1/4 inch.
It is highly recommended you use the Air Lift Air Hose Cutter # AL10530 for the air lines to get the most concise cut of the lines. view full answer...
Yes, the Tow Ready Custom Fit Vehicle Wiring for the 2009 Aspen by Chrysler, item # 118390, is the correct wiring harness for your Aspen and you will need one other item to complete the wiring to lockout the brakes on your boat trailer surge coupler.
You can go one of three ways for this wiring. The easiest way in my mind is to install the # 118390 T-One and then splice the 5-Flat Vehicle End 5' Wiring Harness, item # HM37908, to the 4 like wires left by removing the 4-way vehicle end... view full answer...
We have electric brakes that have the weight capacity for a tandem axle trailer with a nearly 24,000 lb GVWR, and I can tell you how to determine if they will fit, but we don't have any way of knowing the correct brakes for a 1994 Trail King trailer. The electric brakes that do have the capacity you need are the following:
- Electric Trailer Brake Kit w/ Dust Shields - Self-Adjusting - 12-1/4" - Left/Right Hand - 12K # AKEBRK-12
These brakes measure 12-1/4" diameter x 5" wide, so in order... view full answer...
To replace the Duo Therm AC unit on your 2006 Holiday Rambler Ambassador I recommend the Furrion Chill HE RV Air Conditioner System - Manual - 15,000 Btu - White # FR92PR.
The # FR92PR AC unit is a perfect replacement for your older Duo Therm unit and since the air distribution box has a built-in thermostat, it's compatible with both ducted and non-ducted systems and no complicated wiring is required. It fits the same opening (14" square) and uses the same 110v. wiring of any standard... view full answer...
The transmission cooler # D13102 you referenced is recommended for compact cars although you can still use it. Checking the measurements of the potential area is key.
I recommend you measure the space you have for installing a transmission cooler to gauge which cooler will fit best. Select the correct transmission cooler by determining where there is enough space to mount it. The best three positions to mount the transmission cooler in order. At Position A, where the transmission cooler... view full answer...
The Dexter E-Z Flex Heavy Duty Rubber Suspension System # K71-653-00 is designed to be used with 35 inch axle spacing and a 8,000 lb capacity specification. On your trailer, if you measure the distance between the center of one axle to the center of the next axle it needs to measure 35 inches. The axle capacity needs to be 4,000 lbs. or less per axle.
If you have 33 inch axle spacing you can use the Dexter E-Z Flex Heavy Duty Rubber Suspension System # K71-652-00 and it has a 6,000 lb... view full answer...
The Yakima JayLow part # Y04073 would be a great option for a kayak carrier that is high quality and can fold down when not needed like you said you were intersted in. Then for a quality roof rack that doesn't cost as much as some of the high end racks we have the Rhino Rack roof rack part numbers # RRVA126B-2 and # RRSX100 which is a confirmed fit. I really like the Rhino Rack roof racks as they are on par with the other brand manufacturers yet don't cost quite as much. view full answer...
For your 2007 Chrysler Aspen, we have the Curt Front Mount Trailer Hitch Receiver # 31297. We unfortunately don't have any photos of this installed on either vehicle you mentioned, however I have attached a photo of how this hitch attaches so you can see how it fits right under the fascia at about the same height as the air dam underneath. view full answer...
The Yakima FatCat EVO 6 Locking Rooftop Ski and Snowboard Carrier # Y03096, or the Yakima FatCat EVO 4 Locking Rooftop Ski and Snowboard Carrier # Y03095, will fit directly to the T-Slot of your roof rack but only with the adapting hardware kit. The necessary hardware can be found in the Aero Crossbar SmarT-Slot Kit 2 for Yakima FatCat Ski and Snowboard Carriers # Y03098. I spoke with my contact at Yakima and confirmed this hardware is what you will need to mount the FatCat to your crossbar's... view full answer...
The Titan Chain Snow Tire Chains part # TC4219CAM are what I recommend for a 2008 Chevrolet Silverado with 225/75-17 Dual Tires. These chains are actually designed specifically for dual tires and they have cam tighteners for easy installation. The twist link construction will provide great traction in both deep snow and ice. view full answer...
Since your 2007 Chrysler Aspen does not have trailer wiring currently you are going to need to first start with a 4-way. For that you would want the part # 118390. This is a plug and play option designed to fit your vehicle. Check out the install video for more info.
Now if your trailer does not have brakes all you would need is the part # 37185 as an adapter to convert the 4-way to a 7-way.
If you do have trailer brakes you would need the # ETBC7 instead of the # 37185 and a brake controller.... view full answer...
Installation time is going to vary by shop and the experience of their mechanics. If you are going to an RV dealer that has experienced mechanics that have done hard wire installations several times in the past, I would say that the install time for the P-3 brake controller, # 90195, the 4-Way wiring harness, # 118390, and the brake controller installation kit, # ETBC7, will require 3-1/2 to 4 hours of install time.
Here at our facility we do video installations and the time required... view full answer...
Powered trailer wiring harnesses like # 118390 have a direct connection to the battery for 2 reasons. First, it powers the trailer lights instead of drawing the power and the signals all through the vehicle tail light wiring. This helps protect the vehicle wiring. And second it offers additional circuit protection beyond what a non-powered converter can.
Basically, you want as much isolation between the vehicle sensitive wiring and electronics and the trailer wiring. The last thing you... view full answer...
I have a solution for towing mirrors for your 2007 Chrysler Aspen, but we do not carry any custom towing mirrors that will fit your vehicle.
Instead, I would recommend a universal fit towing mirror like the CIPA Clip-On Towing Mirror, # 7070. This mirror will clip on to the OEM mirror housing and secure with rubber straps around the back of the mirror.
We also offer the CIPA Deluxe Door Mount Mirror, # 11650. This style of mirror will attach to the bottom of the door and also between... view full answer...
The only style of engine heater I can recommend for your 2008 Chrysler Aspen with a Hemi is a magnetic pad like the part # KH24100.
There are no cartridge style heaters available. view full answer...
I would recommend the Tekonsha Prodigy P2, # 90885. It is easy to setup and easy to adjust when loads change.
Brake controllers are not vehicle specific so any of the brake controllers you mentioned will do a good job. If you like the P2, then you will want to use the wiring adapter # 3020-P, that is confirmed as a fit for your Aspen. I am sure you will not be disappointed. view full answer...
Go To Results