The Cruiser Fastener Caps # CR82650 that you referenced are a universal fit and don't have a specific size bolt that they fit.
I have attached a link to our available selection of fasteners and caps for you to reference. view full answer...
Does your Camaro have two exhaust pipes or a single exhaust pipe? We only have one hitch that fits your vehicle with the Curt # C11117 but this cannot fit versions of your 1995 Chevy Camaro that have dual exhaust.
This hitch would work great to carry a bike rack like the Hollywood Racks # HR200Z. view full answer...
Since you have a 2015 Camaro LS there are extremely limited options for bike racks. The only choice if you do not want to add a hitch is to use the SeaSucker Komodo Bike Rack for 1 Bike item # 298-BK1910-BK. This will mount one bike weighing up to 45 lbs to the rear of your Camaro using suction cups.
To use a two bike bike rack with your car you will need to add the Draw-Tite Trailer Hitch item # 24850. This hitch is custom fit and bolts to your Camaro with included hardware. It does... view full answer...
I spoke with my contact at Derale and he stated that on the Dual High-Output, Electric Radiator Fan-and-Shroud Assembly, # D16927, the fan on the driver side would be in the upper position making the fan on the passenger side in the lower position.
This fan is a puller, meaning that it mounts between the radiator and the engine and pulls air through the radiator. You will need to make sure that you have enough clearance to install the fan. It is 3-3/4 inches wide, 18 inches tall, and... view full answer...
The # D13950 Derale Atomic-Cool Remote Transmission Cooler Kit w/ Fan can be used in your 1969 Camaro with 5.7L Engine. I reached out to Derale and they confirmed this.
This cooler is designed to be mounted anywhere. According to the installation manual, the purpose is to be able to mount the cooler away from the front of the vehicle therefore not blocking airflow to the radiator/condenser. This cooler can be mounted anywhere space permits. Always keep in mind that the cooler still needs... view full answer...
Your 2016 Chevrolet Camaro LT was never designed for towing a trailer but I do know it is done. Since Chevrolet did not design it for towing they give no weight capacities for towing so there is no way of knowing what towing your 2021 Harley Davidson CVO Tri-Glide could damage on your Camaro. If you choose to tow it I recommend finding a very light trailer as the Tri-Glide weighs 1,269lbs and the Draw-Tite Trailer Hitch Receiver # 24938 is rated for up to 2,000lbs.
The Curt Powered Tail... view full answer...
The Linxup GPS Tracking Device - 3-3/4" Long x 2" Wide x 1" Tall part # 300-AT3 has been recently upgraded to work with 4G network. It also has a 3G fallback so basically it will work with any cell phone service that supports the 3G or 4G network. view full answer...
The Curt # C11117 Class I hitch fits 1995 single exhaust Chevy Camaro models. It won't fit models with twin tailpipes next to each other or models with two cutouts in the bumper for the exhaust to pass through. view full answer...
Yes. The Curt # C59496 will provide enough power for incandescent lights on a trailer without issues and is a confirmed fit on your 2015 Chevy Camaro. view full answer...
The Curt Trailer Hitch # 11117 that you referenced should work well on your 2001 Chevy Camaro. Having dual exhaust will not cause a problem is this hitch is confirmed to fit other F-bodies like yours that come standard with dual exhaust.
You will need to be sure you do not exceed the towing capacities of your vehicle and this hitch with your trailer. Your owners manual will have the towing capacities listed for your vehicle.
When determining the overall towing capacity of a setup you... view full answer...
The Curt Class I Receiver Hitch # C11900 that you referenced is confirmed to fit all models of the 2016 Chevrolet Camaro, so it will work well for your Camaro SS to carry a Class I compatible bike rack.
I checked the instructions to see if any bumper fascia trimming is required for this hitch on your vehicle. The instructions indicated that the center, inside, lower edge of the fascia may need to be trimmed if necessary, and that the hitch is intentionally designed to be close to the... view full answer...
I have contacted the hitch manufacturer of the Draw-Tite # 24850, and they stated that it is a fit for your 2013 Chevrolet Camaro ZL1, as long as it is not a convertible and does not have a dealer installed ground effects package.
Please note that this is rated as a Class I trailer hitch and has a tongue weight limitation of 200 pounds and a gross towing weight limitation of 2000 pounds. It is advised that you check your vehicle owners manual and ensure that your vehicle will be capable... view full answer...
We have hitch cover # AUT2-ARMY-C for a 1-1/4 inch hitch.
The only other option is to use an adapter such as # HTAD to go from a 1-1/4 inch hitch to a 2 inch. But this will also make it stick out further. view full answer...
There are better options available for carrying bikes on your 2011 Camaro. Trunk mount bike racks have been around for a while and are a good, inexpensive option to carry bikes, but like you, many people are weary of using a trunk mount rack because the weight of the bike rack and the bikes is sitting on the trunk and bumper. Bike rack manufacturers test these bike racks and as long as the weight capacity of the bike rack is not exceeded and the bike rack is installed properly, you should... view full answer...
The Hollywood Racks Expedition trunk mount bike rack # HRF6-2 is listed as a fit for your 2011 Chevy Camaro. This rack is designed to fit over most factory spoilers as well. I have included a link to a video review of the rack for you.
If you will be carrying any bikes that do not have a top frame bar that goes straight across (like a typical mens bike would) then I recommend using bike adapter bar # HRBA-PRO. This will allow you to carry those bikes more level and will provide better... view full answer...
The Draw-Tite Sportframe Trailer Hitch Receiver # 24850 measures about 9" from the hitch pin hole to the rear of the bumper. The Swagman XTC2 Bike Rack for 2 Bikes # S64670 measures about 8" from the hitch pin hole to the nearest wheel hoop as you can see in the photo I attached. The means that the bike rack will likely interfere with the rear bumper and the only way around that is to use a hitch adapter such as CR Brophy Hitch Extender for 1-1/4" Hitch Receivers - 5-3/4" Long # hes6. This... view full answer...
The Curt Trailer Hitch Receiver # C11222 is our only receiver that is confirmed to fit your 2011 Chevrolet Camaro Convertible, as long as you do not have ground effects.
The Hopkins Wiring Harness # HM11141285 will give you a 4-way flat connector that you can use to control the lights on small trailers you may pull. It can also be used with Auxiliary Lights # C53201 in the event your hitch mounted accessory impairs the view of your tail lights to other drivers. view full answer...
The ball mount help article also mentions that on a Class I or II hitch you have to use the ball mount indicated by the hitch manufacturer and specified in the instructions. In the instructions for Curt trailer hitch # C11373 specified ball mount is # C45521 which is a Class II ball mount.
The reason that this Class II ball mount will fit this Class I hitch is that Curt does not install a safety stop in their Class I hitches to prevent installation of Class II accessories. All other hitch... view full answer...
You are correct. We do have the Curt wiring harness # C56197 listed as a NO-FIT for a 2014 Chevy Camaro that has LED tail lights because those models require a powered converter to power the trailer lights without damaging the vehicle wiring. On models that do have LED tail lights you would need to use Curt harness # C59236. view full answer...
The Curt Trailer Hitch # C11222 can be installed on your 2013 Chevy Camaro convertible, just so long as the Camaro does not have the Ground Effects Package, which could be the case with a Z71 so you will want to make sure.
This is a Class I hitch with a 1-1/4 inch receiver and is a bolt-on installation so you can install it without any drilling into your Camaro's frame. view full answer...
Go To Results