It sounds like you are trying to connect the running light circuit wire of the Curt Vehicle Wiring Harness # C58044 to your 2006 Buick LaCrosse. It would not matter which of the tail light wires you use for this installation. Both wires carry the same circuit. view full answer...
The 2003 Buick Rendezvous can be flat towed without damaging the automatic transmission by installing a transmission lube pump. I do not sell any lube pumps. You should also consult the vehicles owners manual to determine if there are any specific requirements to tow your vehicle.
The automatic transmission would need to be in neutral while flat towing the Buick and the ignition key will be turned to the unlocked position to release the steering wheel lock on the vehicle.
Roadmaster has... view full answer...
There is a plug in style connection at the tail light assemblies on your 2013 Buick Verano for the Tow Ready T-One Wiring Harness, # 118564. Once you remove the felt liner covering the back of the tail light assembly, you will see a black connector plugged into the tail light assembly. You will simply unplug that connector to connect the wiring harness.
I have attached a photo from the installation instructions showing what the tail light connector looks like. I have also attached a link... view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" Item # C12009 for the 1996 Buick Roadmaster installs without need to lower your exhaust but does require some drilling. All required hardware is included. Tools needed for installation include 15mm wrench and socket, 3/4-inch socket, drill with 9/16 bit and a torque wrench. I have linked a helpful article concerning hitch installation tips. view full answer...
The control box for the SMI Stay-IN-Play DUO # SM99251 is designed to be installed in the engine compartment on any vehicle, including your 2017 Buick Enclave. It is actually somewhat weather resistant and can take some water getting on it although you want to avoid this being a constant for the control box. If you are wanting to mount the control box inside your vehicle at the rear cargo area then you will need to supply a longer hose for the vacuum and make sure that you can install it... view full answer...
There are a few methods that people use when they need to run a power wire from the vehicle battery to the rear of the vehicle. One method involves routing the wire as much as possible through the frame. What you would need to do first is determine if the frame has a hole in which a wire can be run and if there is space enough for it.
You would need a long rigid and skinny object, like a coat hanger to run through the frame, tie off the wire to it, and then pull it back through. This... view full answer...
When flat towing any vehicle we have to recommend you stick with what the vehicle manufacturer outlines as the flat towing procedure in the owners manual. In most cases the reason is because the steering wheel has to be unlocked and the only position the steering wheel is unlocked for some vehicles is with the key on which is why then the battery has to be disconnected so it doesn't drain quickly.
You'd have to check with Buick to get that totally verified but if you left the key on for... view full answer...
To install the Hopkins Rear View Camera with Backup Sensors, part # HM60195VA, to your 2011 Buick LaCrosse you will need to use a circuit tester, part # PTW2993, to test the functions of the vehicles wires to determine which one carries the reverse lights.
The wiring color for vehicles can vary from different makes, models, and model years. To be absolutely certain which function each wire carries, you will want to use the circuit tester.
I am including a link to a video installation... view full answer...
At the rear of many Buick Enclave models, there is a cover that is in the center of the bumper fascia. If you view the attached video and at the 0:25 second mark you will see our tech removing the panel. The removal of this panel may not be applicable to your model vehicle.
For your 2017 Buick Enclave, I recommend the Curt Class III Trailer Receiver Hitch, # 13424. This hitch have the 2 x 2 inch receiver opening that will give up more choices of hitch accessories like bike racks and... view full answer...
The 7-way kit part # 118287 will fit behind the rear hitch access panel of your 2020 Buick Enclave. You might have to bend the bracket back a little bit so that the cover fits over it but that wouldn't be an issue at all. view full answer...
Installation of a brake controller on your 2007 FJ Cruiser will require hard wiring with a Brake Controller 7- & 4-Way Installation Kit, item # ETBC7. We have detailed instructions, see link, and a video installation, see links, of this kit and a brake controller being installed on a 2008 FJ Cruiser for you to review.
If your FJ does not have a 4-Way trailer connector installed you will also need to install a T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, item # 118405, prior... view full answer...
Trailer wiring harness # 118270 will plug into a single connector on your 2013 Buick Enclave. You will need to locate the vehicle’s connector located under the Enclave on the passenger's side. Look for an
opening to the right of the muffler. Reach up into opening to locate the grey connector. Disconnect the mating protective cover and discard. Connect the Enclave connector to the mating harness. All connector surfaces should be clean and free of dirt. Be careful not to damage the locking... view full answer...
Some companies prefer to be more cautious with their product ratings than others. Curt requires the use of stabilization straps, # 18050, on all of their Class I and II trailer hitches, regardless of tongue weight capacity, in accordance with their warranty requirements. The Draw-Tite and Hidden Hitch trailer hitches do not require a strap, but a strap can still be used and would not be a bad idea in any application using a larger bike rack.
I would recommend the Curt Trailer Hitch, #... view full answer...
The Draw-Tite Receiver Hitch, part # 36652 for your 2017 Buick LaCrosse does require some fascia trimming, but the 5" x 6" area is located on the portion of the bumper fascia that's tucked on the underside of the vehicle, so it won't be visible.
As outlined in the attached installation instructions, you will need to temporarily remove the bumper fascia by first removing the license plate and taillights, so you can gain access to the last two fascia tabs that hold it in place.
Once the... view full answer...
According to the installation instructions for your 2013 Buick Enclave, the vehicle’s towplug will be located on the rear passenger side of your vehicle.Locate the opening just to the right of the muffler. Up in the opening you will find the vehicle's tow plug. The wiring will have a grey plug at the end and this plug is where # 118270 4-flat harness will plug in to your Buick's wiring.
I have liked a installation video that will show you exactly how to install the # 118270 wiring harness. view full answer...
The Kuat Transfer V2 Bike Platform Rack # KU74FR you asked about will not allow the wheel hook to swing freely. The arm tension is adjustable so you can ensure that you won't have any issues. There will not be any contact with the vehicle.
I recommend measuring from the center of the hitch pin hole on your 2019 Buick Envision to the outermost part of the bumper. The closest part of the carrier when folded up is 6 inches from the center of that hitch pin hole. view full answer...
Yes the factory trailer connector will be located behind the center of the rear bumper. It should be a square shaped plug with 4 pins. Once you locate it you can plug in the Curt wiring harness # C56325 and you will be good to go. It is recommended to get a bracket like # C42CR to secure the connector. view full answer...
Thanks, I checked with Draw Tite and their hitch part # 76300 that you referenced does fit your 2020 Buick Envision Premium II as this hitch fits all models. Your dual exhaust setup would not be an issue at all. view full answer...
I looked up the online owner's manual for your 2019 Buick Envision and on page 310 it states to turn the ignition on, and shift the transmission to N(Neutral), then to turn the ignition off. I'm not sure where you are reading your instructions at but you want to make sure it is under the heading for Dinghy, Flat, or Recreational Towing.
Please note that the manual also calls for fuses 29 and 32 to be removed from the body control module (in the instrument panel fuse block). I recommend... view full answer...
In order to install this Draw-Tite Receiver Hitch, part # 36309, you will need to remove the rearmost fastener which secures the load leveling control housing to the frame rail and discard it. You will then trim the load leveling control housing around where the previously removed fastener was. See the picture to the right for further clarification.
Some other items you may need:
Draw Bar # 36063
Ball # 19258 or 19256
Trailer Wiring # 119176KIT view full answer...
Go To Results