To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.
Features:
Specs:
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located in the rear cargo area. You will have to remove the plastic threshold cover, side panels, cargo trays, and interior trim panels to access this harness.
Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery and insert the provided fuse.
Once installation is complete, the 4-way flat connector will be stowed in your rear cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A ModuLite power module is built into this T-One connector. With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
Average Customer Rating: 4.8 out of 5 stars (143 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.2024 Sienna XLE installed easily, just plugs in, but side panel removal takes some thinking. Watch the video for similar products. Get a cheap panel removal tool and life is easier! Used small machine screw to bolt relay box above the small removable panel.
See photo. If ever needed this allows access to the units fuse holder without having to go through the work of removing side panels again. Routed trailer wire out bottom of this small panel and wiring then stores neatly in the side box.
Easy installation with clear instructions. Very well packaged. Arrived very fast and the customer service was great! I knew where my product was at all times and when it arrived at my house.
This worked great on our '22 Sienna. Things plugged right in. I got a little creative with the mounting and wire routing. I mounted to the back side of the plastic access panel, then cut a notch in the access panel to run the wire through, into the rear cargo area. It's worked out well for me. I have the flat four with wire coiled up inside the rear cargo area of the vehicle, which wouldn't be ideal for somebody using the trailer all the time, but for me, using the trailer 5-10 times/year, it's just fine and keeps things out of the weather.
Fits perfectly on my 2022 Toyota Sienna XLE and was very easy to install.
Simple installation. Good quality product. I've been using it for over a year now with no issues.
Installed it myself and towed my camper from NC to Cali with it! Worked great and held up the whole time!
Starting at 5:15 out of 12:08 hitch installation you tube video by MasterJacks, followed his guide. Broke plastic installation pins, bought Ford plastic pins at Autozone, Toyota pins not close to OE. Used adhesive backed hook and loop fasteners to mount electronics box. Everything works.
It was simple to install!!! It was just as it was described.
Pritchard
2/19/2024
It was easy to install and works great! It was just as it was described.
Works well. Instructions OK, though could be clearer.
This part makes it easy to have a complete hitch setup
Wiring harness connected right up to the 2022 Toyota Sienna. It comes with some Tape and mounting instructions that didn't quite line up with a Sienna that had a spare tire. I don't like 2 sided tape because I don't believe it will last in a hot car. I got a couple of self tapping screws and mounted the plastic box to the aluminum spare tire mount. Also used a self tapping screw to attach the ground to the aluminum spare tire mount.
Just got it 2 hours ago and it is all installed. Did a hitch receiver as well. Wiring went good. Used the rubber plug to run it through so it’s permanently tied to the receiver. Thanks!
Installation was a breeze. No wire splicing. Plugged into my 2021 and it's been working great!
Tomas
4/27/2023
still going strong!
Works great on my Sienna. Easy install once I got over popping interior panels off my brand new car
Hooks right up to an open connector behind the spare. There’s a rubber plug that goes through the bottom of the car, I used a knife to cut halfway through it and just slid the harness into the middle of the plug if that makes sense. Ran the wires to the hitch without a problem. Dropped the plug back in and it basically molded around the harness wires. Hooked up a trailer and it worked great
So far so good. Works on my small lawn mower trailer just fine
Direct fit to factory wiring harness. Easy to install. Using for a year now without a single problem
Easy to install, works exactly as advertised. Had to modify the installation slightly to clear the spare tire, but it was easy.
It takes a 5 minutes to complete a gob.
On a package picture it shows different type of wire harness but inside is exactly what I needed.
Thanks again.
Incredibly easy install. The Sienna has a wiring harness behind the spare tire so it was plug and play. I was able to use one of the rubber grommets to route the wires to the hitch.
The 2021 Sienna has the connector underneath the spare tire, two mounted screws perfect for the grounding wire, and a rubber cover for easy access to underneath the vehicle to route your 4-way.
The trailer hitch receiver was easy to install, but the instructions were also wrong (removing the cover underneath the car was on the driver side, and not the passenger side). 5 stars as long as they get the instructions fixed so people don’t unnecessarily tear apart their car!
Excellent. Five stars.
Very easy to install, took me about half an hour. Only minor complaint is that there were a few small spots on the hitch that were not powder coated, so I’ll touch those up with enamel. I was also able to trim the underside panel a little more conservatively so as to leave the aft bolt attachement in place. Maybe not a big deal but given that it’s plastic and supposed to protect wiring from salt and road grime, I figured leaving as much intact as possible would be a good thing. etrailer shopping and follow up were great
Solid trailer hitch, works great. Easy to put on. I like that there are places we can attach ratchet straps for our rooftop kayaks too.
Thos wiring kit works great and fits perfectly under the spare tire where the connector is located. The tekonsha kits Instructions say to pull panels and look under carpet by rear seat in hatch area. Wrong. That's too much work and you'll get no where but once you figure it out it's perfect and easy to install.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Anthony B.
5/14/2024
No issues have presented themselves since it has been installed. Still working as it is supposed to.