Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Adapter kit lets you carry 1 bike with fat tires on your Saris Freedom bike rack. Just replace the existing cradles with these larger, deeper cradles designed for fat tires up to 5" wide. Uses existing hardware. Extra-long wheel straps included.
Features:
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today I'll be showing you how to install the Saris Fat Tire Adapter Kit part number SA4419. You can see we all ready have the rack installed, now we'll just show you how to swap out the wheel trays. Now this part number is only one set of wheel trays, the manufacturer does recommend that when you're holding one bike or carrying one bike that you carry it on the cradles or saddles closest to the rear of the vehicle. We'll do is just loosen up this yellow knob, push down this yellow button and just slide the tray out. Take the new tray, slide it on and then just tighten it down. Now here on the other side you can see this wheel tray is on the inside of this arm, we are going to have to remove this arm. What we'll do here is just loosen this knob here, push down that button pop this one off and we'll use the Allen wrench and a seventeen millimeter wrench or ratchet whichever you prefer, loosen this up.
Should slide right off then we can remove this other inside wheel tray. Take the new tray, slide it on then just leave this loose so you can adjust it. Slide the arm back on and then tighten it down. If you are carrying a flat tire bike you may need to use the included straps. What we're going to do is just take this end of the strap slide it through, come back up this hole here. Then there's these little tabs in the bottom on the strap if you can see these and those going to give those tug snap this in place.
Then you'll just come around the bike and then flip it in place. Now that we have the trays installed and our straps are undone I'll go ahead and place the fat tire bike into our new wheel trays. I'll just need to adjust this back one just a little bit and with that in place, just make sure that these wheel hooks are extended all the way out. Bring this up, clamp that down then we'll finish off by bringing the cam buckle straps through the rim and spokes. Securing it with the cam buckle and with our bike all loaded up that will complete today's review of the Saris Fat Tire Adapter Kit just part number Sa4419. .
Average Customer Rating: 4.6 out of 5 stars (34 Customer Reviews)
Adapter kit lets you carry 1 bike with fat tires on your Saris Freedom bike rack. Just replace the existing cradles with these larger, deeper cradles designed for fat tires up to 5" wide. Uses existing hardware. Extra-long wheel straps included.
These fat bike wheel trays are excellent. Fit my 4.8 inch tires fine. Fit onto the saris rack easy peasy. Not much else to say. Does what they are made to do and easy to mount and use. I’ve also put a regular mountain bike tire in it and it holds it fine.
Rocket to the moon quality!! Handles so many different tire sizes what a great bike tool. Takes a beating was easy to install withstands the Minn. weather WHAT else could you want.
So far, so good. Great customer service at eTrailer, they are easy to reach and they do try to get things right. These adapters are essential for the 60 pound bikes that the Freedom rack is designed to carry--the stock cups are just too narrow for any tires wider than about 2". Add their cost to that of the carrier--but still a reasonable price for a very solid, functional rack.
This bike rack was designed for two bikes.
I use it for one only fat tire e-bike as it is still within the weight restrictions.
It carries my bike well and I'm pleased with it's performance. My suggestion is to always be within the weight restrictions when deviating from recommended us.
The fat wheel holders are very easy to install. You do have to use an Allen wrench and a 17mm wrench to remove and replace one of the clamp arms, but it’s simple. It can easily hold the 4.8” tires on my Trek Farley.
The fat tire adapters for the Saris rack are excellent. You just slide the standard wheel holders off and then slide the fat tire adapters on. They work exactly like the standard wheel holders.
Fat Tire Adapter Kit for Saris Freedom Bike Racks : Zoom, Zoom Shipping
Exactly what I needed! Makes carrying my fat-tire bicycle simple!
Excellent replacement parts
I have only received the extra items and not the actual bike carrier.
Love the installation ease.
Well made and should do what I need!
They work as advertised.
Bruce
10/3/2022
This product is still working well for me. My only complaint is that the tire straps and support straps can be hard to get latched. Those could have a better design. As we get older are hands are not what they used to be.
Great product!! Fits our bikes very wel l!!
great service, product worked great!!!!
Expired services no issues! Would purchase from you again!
easy to put on
Great service
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Ron T.
5/27/2018
No changes AWSOME! Keep bringing it