Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2016 Jeep Cherokee- Video

Today on our 2016 Jeep Cherokee we're going to show you how to install the Roadmaster Flexo Coil Diode Wiring Kit for a seven pole to six pole connection. Part number is RM15267. The first thing I'm going to do is take my six pole plug, I'm going to take the provided screws here. I'm going to attach that plug right to the bracket. Once that's attached we'll pull the boot off the back, and we want to slide our wiring through the boot. Now, in typical applications here you're just going to have the four wires. more

Watch Video

2/16/2017 2:47:39 PM

Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2013 Jeep Wrangler Unlimited- Video

Today on our 2013 Jeep Wrangler Unlimited we'll be installing the Roadmaster Diode seven-wire to six-wire Flexo-coil wiring kit, part number RM-15267. All right, here's what the wiring looks like installed. As you can see it doesn't take up very much space on the front of the vehicle at all, tucks up nicely out of the way. This will allow us to safely flat-tow our vehicle behind our RV and have all of our factory lighting functions still work. We don't have to worry about using magnetic tow lights or having an extra set of lights added to the vehicle to tow it. This utilizes the factory light bulbs already in the vehicle utilizing diodes. more

Watch Video

1/12/2017 2:54:11 PM

Best 2009 Jeep Wrangler Tow Bar Wiring Options- Video

Today on our 2009 Jeep Wrangler we're going to take a look at the best wiring harnesses available for a flat tow setup. Here we're going to have our Trailer Mate t-style connection setup. This is part number TM781124. This harness protects the towed vehicle from feedback but it does not protect the motorhome from feedback. Here in the middle is going to be a very similar setup to the Trailer Mate. This one's from Hopkins. more

Watch Video

12/8/2016 2:24:55 PM

Best 2008 Jeep Wrangler Tow Bar Wiring Options- Video

Today on our 2008 Jeep Wrangler we're going to take a look at the best wiring harnesses available for a flat tow setup. Here we're going to have our Trailer Mate t-style connection setup. This is part number TM781124. This harness protects the towed vehicle from feedback but it does not protect the motorhome from feedback. Here in the middle is going to be a very similar setup to the Trailer Mate. This one's from Hopkins. more

Watch Video

12/8/2016 2:24:42 PM

Best 2007 Jeep Wrangler Tow Bar Wiring Options- Video

Today on our 2007 Jeep Wrangler, we're going to take a look at the best wiring harnesses available for flat tow set up. Here we're going to have our TrailerMate T-style connection set up. This is part number TM781124. This harness protects the towed vehicle from feedback, but it does not protect the motorhome from feedback. Here in the middle is going to be a very similar set up to the TrailerMate, this one's from Hopkins. This is going to be part number HM56200. Again uses a T-style connector so we're going to plug right into our factory harness. This is a diode pack, this is like having four diodes in one little box. more

Watch Video

12/8/2016 2:24:28 PM

TrailerMate Tail Light Wiring Kit Installation - 2015 Jeep Wrangler Unlimited- Video

Today on our 2015 Jeep Wrangler Unlimited Rubicon edition we are going to be taking a look at and installing the trailer mate custom tail light wiring kit for towed vehicles part number TM781124. Here's what this wiring is going to look like once it is installed on the vehicle. You've got your four flat connection here at the front which is going to provide you power and ground in order to power the lights at the rear of the towed vehicle with power coming from the motor home. It comes with a bracket to help you mount it, and it does also come with a dust cover to go over the four pull when not in use. This wiring kit teased directly into the factory connectors on the tail lights so there's no cutting or splicing required in order to install this system. It features built in diodes to help with overload protection and protect the vehicle's electrical system, and with this system you don't have to worry about it messing with the vehicle's electrical system when not being towed by the motor home. Now, let's go ahead and show you how to install it. To begin our installation, we are going to go ahead and route the four pull wiring from underneath the rear of our vehicle all the way up to the front where we will mount our electrical connection. more

Watch Video

11/28/2016 3:23:16 PM

Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2016 Jeep Wrangler Unlimited- Video

Today in our 2016 Jeep Wrangler Unlimited we're going to be taking a look at and installing the Road Master Diode Seven Wire to Six Wire FlexiCoil Wiring Kit. Part Number RM-15267. First thing we'll need to do to begin our install is we're going to need to remove this little cover right here and in order to do that there's going to be six total push pins. Four up along the front here and then two more along the backside that I'll show you. You can take a flat-head screwdriver. Just pop the center of those down. more

Watch Video

6/29/2016 12:34:06 PM

Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2007 Jeep Wrangler Unlimited- Video

Today on our 2007 Jeep Wrangler Unlimited, we'll be installing the Roadmaster Diode 7-Wire to 6-Wire Flexo-coil Wiring Kit. This is part number RM-15267. The Roadmaster tow bar wiring diode kit allows you to use your vehicle's tail lights and wiring system while preventing feedback from your RV. It lets you wire your vehicle to accept your RV's tail, brake and turn signal lights for flat towing. Here's what our kit consists of, the most important part being the four diodes that we're going to use to tap into our vehicle's stock wiring, so we can have towed vehicle lights behind our RV. We have a bundle of four pole flat wiring here. We'll run this to the front of our Jeep using this connector here, which is a six pole, where the flexo wiring here will connect to. more

Watch Video

6/27/2016 12:12:39 PM

Roadmaster Universal Diode Wiring Kit Installation - 2007 Jeep Wrangler Unlimited- Video

Today on our 2007 Jeep Wrangler unlimited, we'll be installing the Roadmaster Universal Hy-Power Diode Wiring Kit, part number RM-152. In conjunction with this, we'll also be using the Roadmaster 7-wire to 6-wire Flexo-Coil Kit, part number RM-146-7. The Roadmaster tow bar wiring diode kit allows you to use your vehicle's tail lights and wiring system while preventing feedback from your RV unless you wire your vehicle to accept your RV's tail brake and turn signal lights for flat towing. Here's what our kit consists of, the most important part being the four diodes that we're going to use to tap into our vehicle's stock wiring so we can have towed vehicle lights behind our RV. We have a bundle of 4-pole flat wiring here so we will run this to the front of our Jeep using this connector here, which is a 6-pole where the Flexo wiring here will connect to. Then we have the standard 7-way RV flat which will go in the back of the RV. We have several zip ties here to secure all of our wiring, and some wire loom mesh included as well in case we need to protect it from any moving parts or sources of heat. We also have an optional bracket here in case your tow bar base plate doesn't already have a spot to put your connector here, so this'll allow you to attach it. more

Watch Video

6/27/2016 12:11:43 PM

Hopkins Tail Light Wiring Kit Installation - 2016 Jeep Wrangler Unlimited- Video

Today in our 2016 Jeep Wrangler Unlimited, we're going to take a look at and also show you how to install the Hopkins custom tail light wiring kit for towed vehicles. Part number is HM56200. All right, now here's a great look at what our wiring kit's going to look like before we start installing it. You can see here's the heart of the system. This is a weatherproof sealed box. Inside, it contains diodes. Now, these diodes are designed to prevent back feeding, so we won't have any back feed coming from our RV into our towed vehicle, so we're not going to have to worry about any electrical issues there. Now, we've got our signal wire here. more

Watch Video

6/15/2016 11:35:37 AM

TrailerMate Tail Light Wiring Kit Installation - 2016 Jeep Wrangler Unlimited- Video

Today on our 2016 Jeep Wrangler Unlimited, we're going to be taking a look at, and also showing you, how to install the TrailerMate Custom Tail Light Wiring Kit for Towed Vehicles. This part number is TM781124. Here's what our kit's going to look like. Basically, this is going to provide us with the trailer signal that we need, or a plug-in, at the front of the vehicle to get the trailer signal from our motor home so it'll operate the lights on our vehicles we're heading down the road. That's going to keep us legal. You can see we've got a nice, long coil of wire so we can run from the front of the vehicle to the back. Once we get there, we've got a white ground. more

Watch Video

5/4/2016 10:54:42 AM

Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2012 Jeep Grand Cherokee- Video

Today, on our 2012 Jeep Grand Cherokee, we are going to be showing you how to install the Roadmaster 7-wire to 6-wire Flexo-Coil Diode Wiring Kit, part #RM-15267. Here is what our RM-15267 kit is going to look like. What we are going to have is a good 30 foot length of wire. This allows us to get from the front of the vehicle where we are going to be mounting our 6 pull plug right back to the vehicle's taillights where we want to send that signal. We've got diodes that are going to present back-feed from the car to the motorhome or from the motorhome to the car so it's a really nice, very well-protected system. Then, we've got the umbilical. more

Watch Video

4/20/2016 1:48:07 PM

Hopkins Tail Light Wiring Kit Installation - 2015 Jeep Wrangler Unlimited- Video

Today on this 2015 Jeep Wrangler Unlimited, we're going to review and install a Hopkins custom tail light wiring kit for towed vehicles. Part number HM56200. All right, this is what the wire harness looks like when it's installed on our Jeep. You can see it had its built in bracket here and a four pull cover for the four pull. Now, there's not much to see on this because everything else is installed inside the vehicle. Next, we'll go ahead and show you what all the parts that come with the kit. This is our main wire harness right here with diodes into converter, and you have two T connectors. more

Watch Video

4/7/2016 10:32:04 AM

Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2015 Jeep Cherokee- Video

Today in our 2015 Jeep Cherokee, we'll be taking a look at and installing the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit, part number: RM-15267. Here's what it looks like once it's installed. It's is going to have the diodes to protect your electrical system in your vehicle. And it's going to make hooking up to your trailer very easily without having to run separate set of lights back to the end of the vehicle for your brake and turn signals.This is going to be installed at all times. And the only time it's going to be active is when you plug into your RV. What's nice about this kit is it has diodes. more

Watch Video

3/17/2016 3:37:50 PM

Roadmaster Universal Diode Wiring Kit Installation - 2015 Jeep Cherokee- Video

Today on our 2015 Jeep Cherokee, we'll be taking a look at and installing the Roadmaster Universal Hy-Power Diode Wiring Kit, part number RM-152.Here's what it looks like once it's installed. This is going to have the diodes to protect your electrical system in your vehicle. And it's going to make hooking up to your trailer very easily without having to run a separate set of lights back to the end of the vehicle for your brake and turn signals. This is going to be installed at all times. And the only time it's going to be active is when you plug in to your RV.And what's nice about this kit is it has diodes. So it's not going to allow anything to back feed into your car's electrical system, causing a short. more

Watch Video

3/17/2016 3:36:31 PM

Hopkins Tail Light Wiring Kit Installation - 2016 Jeep Wrangler- Video

Today on our 2016 Jeep Wrangler, we're going to show you how to install the Hopkins Custom Taillight Wiring Kit for Towed Vehicles, part number HM56200. What this is going to allow us to do is hook up our motor home, and it's going to operate the lights on the vehicle just as if we we're sitting inside the car turning the signals on. It does that with the diode converter here, so this box has built-in diodes. This is going to prevent any back feed into the electrical system of the towed vehicle, and the diodes are going to convert whatever signal it's getting from our taillights into a usable signal. That diode converter is going to take the signal coming in from the motor home, it's going to translate it into signals that the vehicle can use to operate its taillights. Great thing about it is when it's not connected to your motor home, there's going to be absolutely no interference. Now to begin our installation, we need to remove the driver's side taillight. more

Watch Video

12/22/2015 11:36:24 AM

Roadmaster Tow Bar Wiring Kit Installation - 2014 Jeep Wrangler- Video

Today on our 2014 Jeep Wrangler, were taking a look at in installing the Roadmaster Universal Hy-Power Diode Wiring Kit, Part Number: RM-154. The first thing that were going to want to do in the installation of our Hy-Power Diode Wiring Kit is going to be to remove the Phillips head screws here at the back of the taillight and remove the taillight assembly from the vehicle. Once you we have it removed from the backside of the vehicle, well go ahead and unplug the manufacturing wiring harness. To do so, depress the tab and pull out. Then well pull back the tape here and peel back the wire loom so we can expose these wires. Once we have the wires exposed, well go ahead and take a wire tester and test our circuits. Now go ahead and test our right turn signal. more

Watch Video

10/29/2015 10:22:07 AM

Hopkins Tail Light Wiring Kit Installation - 2008 Jeep Wrangler Unlimited- Video

Today on our 2008 Jeep Wrangler Unlimited we're going to show you the Hopkins custom taillight wiring kit for towed vehicles. Part Number HM56200. First off, we have this T-connector here, this one with the yellow wire goes to the left-hand side, or driver side. The T-connector here with the green wire goes over to the passenger side. This is our converter right here which takes our input from a 4 pole, that gets the power from the RV, goes through here and divides up to the wire harness, and to the tail lights. This long 4 pole wire harness will get ran underneath the vehicle all the way up towards the front, where it will be held in place by a spracket, also with its protective cover. more

Watch Video

8/8/2015 4:08:57 PM

Trailer Wiring Harness for Towed Vehicles Installation - 2005 Jeep Liberty- Video

Today on our 2005 Jeep Liberty, we're going to show you how to install the TrailerMate Custom Tail Light Wiring Kit for Towed Vehicles. This is part number TM781104. Here's what your harness is going to look like when you receive it. You're going to get a nice quantity of zip ties. We're going to have our small extension which will extend our plug out to where we can get it to our vehicle. We have our mounting bracket for it, a couple of small screws to help us secure that and even a couple of the padded cable hold downs, be able to zip tie our wire to once we run it to the front of the truck. You see the one here that's got yellow, brown, white and red This is going to go inline behind our driver side tail light. more

Watch Video

7/15/2015 10:57:46 AM

Roadmaster Tow Bar Wiring Kit Installation - 2015 Jeep Grand Cherokee RM-154- Video

Today on our 2015 Jeep Grand Cherokee we're going to review and install the Roadmaster universal diode wiring kit for towed vehicles, part number RM-154. Now right out of the package we're going to have some zip ties and a ring terminal, a lead to connect the tow to the towed vehicle, our four diodes and necessary connectors, and then the wiring harness that will connect the towed vehicle wiring ultimately to the our tow vehicle. Now to begin our install we need to remove the rear taillight assemblies. To remove the rear taillight assembly we'll need to start by removing the two push pin fasteners. We'll pry out on the center of the fastener first, releasing it, and then removing it completely. Next we'll pull the taillight assembly towards the rear of the vehicle, releasing the fasteners underneath. Now to assist, you can also use a little pry tool and get between the taillight and the body of the vehicle. more

Watch Video

6/30/2015 2:04:06 PM

Roadmaster Tow Bar Wiring Kit Installation - 2015 Jeep Wrangler Unlimited- Video

Today on our 2015 Jeep Wrangler Unlimited we're going to be showing you how to install the Roadmaster universal high powered diode wiring kit, this is part number RM-154. To begin our installation we're going remove the passenger side and driver side tail light housings here, just a couple of phillips screws will hold those in. Take out the two closest to the middle here, we ought to be able to wiggle that and bring it right out. We'll separate our connector here by pressing in on the tab and then sliding it out. Set that aside for re-installation later, we'll do the same thing for the driver side. Now it's time to test our wires out here and figure out exactly what's what in the harness. more

Watch Video

6/19/2015 9:36:06 AM

Hopkins Tail Light Wiring Kit Installation - 2014 Jeep Wrangler Unlimited- Video

Today on this 2014 Jeep Wrangler Unlimited we're going to show you the Hopkins Custom Tail Light Wiring Kit for towed vehicles, part number HN56200. Now we have our parts laid out before we install. We'll give a quick overview of what goes where. First off, we've got a T connection here. With the yellow wire, that will go behind the driver's side tail light. Take a look at this side here with the green wire. more

Watch Video

5/20/2015 4:17:16 PM

Roadmaster Tow Bar Wiring Kit Installation - 2015 Jeep Cherokee- Video

Today on this 2015 Jeep Cherokee, we're going to show you part number RN-154. This is the Roadmaster Universal High-Powered Diode Wiring Kit. We'll go ahead and cover the parts that come in the kit. You get the 4 high-powered diodes with the terminals. These are crimp terminals, and also some butt connectors for your wires. This is a patch cord to go between your RV and your towed vehicle. This is the wire harness that gets installed on the vehicle. more

Watch Video

4/29/2015 1:06:23 PM

Hopkins Tail Light Wiring Kit Installation - 2006 Jeep Liberty- Video

Today on this 2006 Jeep Liberty, we're going to show you part number HM56203. This is the Hopkins Custom Taillight Wiring Kit for Towed Vehicles. This is what we get in the kit. This is our actual wire harness right here and this is actually a T-connector that plugs into the factory wire harness. This one with the green wire will actually go to our passenger's side. This is our converter that contains all our diodes to protect the vehicle from the towed vehicle and here's our T-connector for the driver's side. more

Watch Video

3/20/2015 5:39:05 PM

Roadmaster Tow Bar Wiring Kit Installation - 1997 Jeep Cherokee- Video

Today on our 1997 Jeep Cherokee, we'll be installing the Road Master Base Plate Wiring Kit, Part RM-154. To start off, we'll want end of our Road Master wiring harness through the hole in the front bumper on the driver's side. We'll use a zip tie to secure it and cut off any excess. We'll cut one of the ends of our wiring, since we'll only need one. We'll then run the cut end of the wiring up through the bumper and into the engine compartment. To make it easier, we'll use a pull wire. In this case, we're using old airline tubing. It also could be any piece of wiring that holds it's shape as well, to pull up our new wire. We'll use the airline tubing, which we'll run down through the engine compartment and out the bottom. more

Watch Video

2/17/2015 11:58:36 AM

Blue Ox Tail Light Wiring Kit Installation - 2008 Jeep Liberty- Video

Today on this 2008 Jeep Liberty, we're going to install part number BX8869 from Blue Ox. This is the Taillight Wiring Kit for Towing. First thing we're going to do is take our 4-Pole wire and we're going to route it to the back. We're going to start by the front bumper over by the base plate. As we work our way back we'll make sure that we stay away from anything moving like suspension components or anything hot like the exhaust. In this case, we we're able to run it underneath the sub frame and then we hid the wire underneath some appearance panels below the vehicle. more

Watch Video

2/2/2015 11:33:08 AM

Roadmaster Tow Bar Wiring Kit Installation - 2013 Jeep Grand Cherokee- Video

Today on our 2013 Jeep Grand Cherokee we'll be installing Roadmaster universal diode kit for towed vehicles, part number RM-154. To begin our install we're going to start at the rear of the vehicle and open up the rear hatch. Next we'll remove both rear taillight assemblies by removing the two push pin fasteners that secure each in position. To remove the push pin fastener we'll pry out on the center of the fastener with just a flat blade screwdriver, and then remove the fasteners completely. We'll go ahead and pop the taillight out. To make it easier you can use the flat blade screwdriver, or we're going to be using a plastic pry tool to get on the front edge of the taillight so it will release from the alignment pins underneath, being careful not to break them. Then we'll go ahead and release the connector from the socket. more

Watch Video

10/30/2014 4:59:09 PM

Roadmaster Tail Light Wiring Kit Installation - 2002 Jeep Liberty- Video

Today on this 2002 Jeep Liberty we're going to install part number RM-155 from Roadmaster. This is Roadmaster taillight wiring kit with bulbs. First thing we need to do is go ahead remove the taillights from the vehicle. There's two torx head bolts that we have to remove. We use a T20 torx head bit to remove the bolts. There's a couple attachment pins here and here. more

Watch Video

10/21/2014 4:55:33 AM

Hopkins Tail Light Wiring Kit Installation - 2012 Jeep Liberty- Video

Today on our 2012 Jeep Liberty we'll be installing the Hopkins 4-Pole Wiring For Towed Vehicles part number HM56204. First step of our install will be to open up the rear cargo door. This will allow us to access the fasteners behind the tail light housings that will need to be removed. Starting on the driver side, we'll go ahead and remove the two bolts, set them aside and then pop the tail light assembly out of its position. Note this can be done easily by using a flat blade screwdriver or in this case, we'll be using a plastic pry bar to dislodge the tail light assembly from its location. Note: Be careful when doing this that you don't break the alignment tabs underneath. Now we'll go ahead and disconnect the wiring running to the back of the tail light. We'll press on the locking tab and remove the socket. more

Watch Video

10/13/2014 11:05:08 AM

Hopkins Tail Light Wiring Kit Installation - 2013 Jeep Wrangler- Video

Today on our 2013 Jeep Wrangler we'll be installing the Hopkins Custom Tail Light Kit for Towed Vehicles; part number HM56200. To begin our install, we'll start with the tail lights. We'll go ahead and remove the rear tail lights. To remove the tail lights, we'll remove the two fasteners that secure it to the body; slip it out of its position. To remove the wiring, we'll press on the locking tab and then remove the connector from the socket. Now we can go ahead and set the tail light aside for installation later. Next, we'll repeat the same process on the other side. Now we've removed the tail light assemblies and we can gain access behind it. more

Watch Video

10/3/2014 5:14:10 PM

Roadmaster Tail Light Wiring Kit Installation - 2012 Jeep Wrangler Unlimited- Video

Today on our 2012 Jeep Wrangler Unlimited, we will be installing the Roadmaster Tail Light Wiring Kit with bulbs, part number RM-155. To begin with, we'll need to route our wires from the front of the vehicle towards the back. To accomplish this, we'll be using a pull wire, in this case a piece of old airline tubing. When we get past the engine compartment, we can route the wire through the frame all the way to the back. Here at the front of the vehicle we will also protect our wire with the loom material provided with the install kit. We can secure it in place with electrical tape. more

Watch Video

9/24/2014 6:46:47 PM

Roadmaster Tail Light Wiring Kit Installation - 1998 Jeep Wrangler- Video

Today on our 1998 Jeep Wrangler, we'll be installing the Road Master Taillight Wiring Kit with bulbs, part number RM-155. To being with, we're going to go ahead and open up the hood of the vehicle. We're going to cut one end of the four flat off. We will not need this in this application. Next we're going to route our wire through the grill and through the engine compartment. It's a good idea to keep a couple extra feet up near the front of the vehicle in case if you have to replace a plug or move the location where your plug may attach to your vehicle. more

Watch Video

8/13/2014 12:47:29 PM

Roadmaster Tow Bar Wiring Kit Installation - 2014 Jeep Cherokee- Video

Today, on a 2014 Jeep Cherokee, we're going to install part number RM-154. This is the Roadmaster Universal Hy-Power Diode Wiring Kit. Before we do any work, want to make sure that the key is in the off position. The electronics in this vehicle are so sensitive that if you disconnect the tail lights, it could cause the computer to malfunction.Let's go ahead and open up the back hatch. Here are two fasteners that we have to remove to take off the tail light. We'll use a T30 torque bit to remove the fasteners. more

Watch Video

8/7/2014 3:57:10 PM

Roadmaster Tow Bar Wiring Kit Installation - 2014 Jeep Wrangler Unlimited- Video

Today on our 2014 Jeep Wrangler Unlimited, we'll be installing the Roadmaster Universal Diode 4-Pole Wiring Kit, part number RM-154. We'll be installing this kit for a towed vehicle that will work in conjunction with the manufacturer's brake and turn signals. Starting on the passenger side, we'll go ahead and remove the taillight assembly. We'll need to gain access to the manufacturer's wiring behind the taillight assembly. With the taillight assembly out, we can go ahead and take the wiring loom and remove it, so we can gain access to the wires. Using my utility knife, I'll go ahead and cut the electrical tape and then cut off the excess loom. Next, using a test light, we'll go ahead and check the manufacturer's wiring to locate the running light circuit and then the single wire that will carry both brake and turn signal circuit. Here at the passenger rear taillight, the white wire with the yellow stripe is going to be the turn and brake signal circuit. more

Watch Video

6/26/2014 4:43:14 PM

Hopkins Tail Light Wiring Kit Installation - 2008 Jeep Liberty- Video

Today on our 2008 Jeep Liberty, we're going to install part number HM56204 from Hopkins. This is a Hopkins custom tail light wiring kit for towed vehicles. First thing we need to do is get our vehicle ready to install the wiring. To do that we'll open up the back hatch and remove both tail lights. We'll remove the two bolts that hold the tail light in place. We'll pull back on the top and bottom and pull it back from the catches here, then we'll remove our tail light from the wire harness. more

Watch Video

5/27/2014 1:43:31 PM

Trailer Wiring Harness Installation - 1999 Jeep Grand Cherokee- Video

Today on our 1999 Jeep Grand Cherokee, we'll be installing the TrailerMate Custom Tail Light Wiring Kit for Towed Vehicles, part number TM781114. To begin our install, we'll first go ahead and open up the rear hatch, then we're going to remove both tail light assemblies. To remove the tail light assemblies, we'll first need to remove the two screw fasteners and then gently pop the tail light out of it's position, being careful not to break the alignment tab underneath. Then we'll go ahead and remove the tail light assembly from the manufacturers wiring by removing the wiring from the socket. To do this, we'll first need to unlock the connector at the red locking tab. Overtime, these locking tabs can really stiffen up and be difficult to move, so I'll go ahead and use a flat blade screwdriver to gently pry it to the unlocked position, then we'll press on the connector lock and remove it from the socket assembly. Now I can go ahead and set the tail light aside. Next, we'll repeat the same process on the passenger side. With both tail light assemblies out of the way, we can now go ahead and start routing our new TrailerMate wiring harness. more

Watch Video

12/26/2013 4:07:37 PM

Roadmaster Tail Light Wiring Kit Installation - 2014 Jeep Patriot- Video

Today on our 2014 Jeep Patriot, were installing a roadmaster tail light wiring kit with bulbs part number RM-155. Now, were going to begin up here at the front of the vehicle. Well go ahead and raise the hood up. Now, were going to take the long wire that has two four flat ends to it. Were actually going to cut one of the four flat ends off. Now the end that we keep that has a four flat connected to it, were actually going to mount up underneath the grill in this vehicle.Now, this vehicle already has a base plate installed so well be connecting it up here at the base plate. more

Watch Video

10/21/2013 9:13:48 AM

Roadmaster Tow Bar Wiring Kit Installation - 2013 Jeep Wrangler- Video

Today on our 2013 Jeep Wrangler we'll be installing the Roadmaster Universal Diode wiring kit, Part Number RM-154. First, to begin our install, go ahead and remove the tail light assembly on the passenger side. To remove the taillight assembly, we'll remove the two fasteners that secure it. Once we remove the fasteners, we'll go ahead and pop the tail light assembly out and then pull it out so we can gain access to the manufacturer's wiring. Next we'll need to test the manufacturer's wiring to locate the running light circuit and the passenger turn signal and braking circuit. Using our test light, we'll go ahead and probe the wires now. As you can see, the white wire with the yellow tracer will be the turn signal and brake circuit and the white wire with the brown tracer will be our running light circuit. We'll need to drill a hole in the bottom plastic panel going up through the foam and out the access hole so that we can gain access to our wires. We'll go ahead and drill our hole. We'll need to get our four-pull harness fed up behind the passenger side taillight assembly. more

Watch Video

9/30/2013 11:16:56 AM

TowDaddy Tail Light Wiring Kit for Towed Vehicles Installation - 2010 Jeep Liberty- Video

Today on our 2010 Jeep Liberty, we'll be installing the TowDaddy Custom Tail Light Wiring Kit for towed vehicles, part number TD3008SSK. To begin our install, we'll first open up the rear cargo door. Then we'll remove the two fasteners securing the tail lik\ght housing on the driver's side. Once the the fastener's removed, we can go ahead and pop the tail light housing out of place. Be careful not to break the alignment tabs underneath, and it may be necessary to use a flat blade screwdriver to assist. We'll be using a small plastic pry bar. more

Watch Video

3/26/2013 6:58:56 AM

TrailerMate Tail Light Wiring Kit Installation - 2012 Jeep Wrangler- Video

more

Watch Video

12/26/2012 6:33:28 AM

Blue Ox Tail Light Wiring Kit Installation - 1999 Jeep Grand Cherokee- Video

All right today on this 1999 Jeep Grand Cherokee were going to install part number BX8869 from Blue Ox. Our first step is go ahead and run our wire from the front to rear on our vehicle. When we do that we want to make sure we stay away from anything thats moving like the suspension component or anything hot like the exhaust. Okay, to route our wire what we do is start at the front immediately behind the radiator going straight up and go over the frame and around and behind the steering box, the non-moving part. Then we go up and over and around the bottom part of the air box and then back down around the frame below the steering shaft. Weve got plenty of room there and then we took a fish wire and we actually ran to one of the holes existing in a frame and we were able to run it back towards the rear axle and pull out our wire there. more

Watch Video

12/18/2012 5:56:32 AM

TrailerMate Tail Light Wiring Kit for Towed Vehicles Installation - 2012 Jeep Liberty- Video

Today on our 2012 Jeep Liberty, we'll be installing the TrailerMate Custom Tail Light Wiring Kit for Towed Vehicles, part number TM781027. First, we'll open up the rear cargo door and then we'll remove the two fasteners securing the driver's side tail light assembly. We'll set those aside, and then using a flat bladed screwdriver, we can carefully pry the tail light assembly out of its position, being careful not to break the alignment tabs underneath. Then we'll press on the locking tab for the connector and remove the wire from the tail light assembly. Now with the driver's side tail light assembly removed, we'll go ahead and repeat the same process on the passenger's side. Next, we'll go ahead and take the new TrailerMate wiring harness with the driver's side and feed it up between the bumper cover and the sheet metal or body of the vehicle. more

Watch Video

11/21/2012 2:37:12 PM

Trailer Wiring Harness for Towed Vehicles Installation - 2003 Jeep Liberty- Video

Today on our 2003 Jeep Liberty well be installing the Trailer Mate custom tail light wiring kit, part number TM781104. Our first step will be to remove the drivers side tail light assembly. There are two fasteners securing the taillight assembly so well go ahead and remove those and sit them aside. Then well gently pry the tail light assembly free from the body of the vehicle being careful not to break the alignment tabs underneath. Next well go ahead and unlock the red locking tab and then press on the connector lock and remove the manufacturers wiring from the tail light assembly. Now we can take the Trailer Mate wiring and plug in line with the manufacturers. more

Watch Video

11/6/2012 9:33:59 AM

Base Plate Wiring Harness Installation - 2012 Jeep Liberty- Video

Today on this 2012 Jeep Liberty were going to install part number 38955. Now first up is to go ahead and start running a wire from the front of the vehicle to the back. It looks like in this case were going to run it through the engine compartment before we get too far along well take a moment and ground our white wire with the ring terminal. Well use number 14 self-tapping screw to attach it to the frame. Then well go ahead and continue on over through the engine compartment and to the grommet that will lead us into the cabin. This is the grommet were going to use. more

Watch Video

9/6/2012 9:53:14 AM

Roadmaster Tow Bar Wiring Kit Installation - 2006 Jeep Commander- Video

Today is 2006 Jeep Commander. Were going to install part number RM-154 from Roadmasters. First thing were going to do is route our cable from front to rear. One end of the cable, youre just cut it off and run towards the back, and it will save the other four pole for the in front of the car. Run our wire to the back of the vehicle, now well go ahead and remove the taillights, and were going to pull wires from the bottom up. Well just kind of unclip our wire harness here and then unplug the wire harness from the light. more

Watch Video

12/30/2011 1:04:52 PM

Roadmaster Tow Bar Wiring Kit Installation - 2004 Jeep Liberty- Video

Today we will be installing Roadmaster universal wiring kit, RM-154, on a 2004 Jeep Liberty. Our first step is going to be to mount this small bracket here in the front of the vehicle that we are going to tie the front end off so it will be accessible when attaching to your motor home. This is a self-threading bolt. It may be slightly difficult to get started but once you do it gets much easier. Our bracket is mounted. I am going to zip-tie my front connector off to it and begin the routing of my wire to the rear of the vehicle. You can see our wire coming up over the axle now. We are going to use these two rear mounting holes. We are going to zip-tie off the rear leader going to our taillights. Now that we have our wire feed run to the rear of the vehicle, what we need to do is remove the taillight lenses in order to splice our wire in. The first step is going to be open the rear hatch of the vehicle and remove the ports bit screws so that we can remove the lenses. Alright, now that we have our screws removed, we can pop our taillight lens out. I even like to go ahead and disconnect my hold-down and then go ahead and disconnect the harness so I can set the taillight lens out of the way. Our harness plug has a locking tab that will have to be pushed up. Then press on your tab to remove your harness. I am going to repeat the same steps on the driver side. 1:46 more

Watch Video

4/29/2011 3:02:38 PM

Roadmaster Tow Bar Wiring Kit Installation - 2006 Jeep Liberty- Video

Today on this 2006 Jeep Liberty we are going to install part number RM-154 from Roadmaster. What this does is allows us to wire up the vehicle so that it can be towed behind an RV. The first step is to route the wire from the front to rear and the wire harness comes with two truck ends on the wiring harness itself. We are just going to cut off one end of it, leave about a foot or so on there in case we need to use it again or in case the original one gets worn out. This 4-pole is going to stay at the front and basically you can think about it as like wiring up a utility trailer. This is going to stay in the front and the car is going to become a trailer at this point. We are going to run our wire between the plastic up in here towards the center as close as possible because in the future a face plate will get installed in that general area. Thread that on through until we come out the other side and we are going to route it all the way back and stay away from the suspension components and we are actually going to run it through the frame. 01:00 more

Watch Video

1/27/2010 4:10:24 PM

  5