Summer Starts Here - Save up to 70%
Trailer Hitch Installation - 2011 Acura TSX - Draw-Tite- Video
Today on our 2011 Acura Txc we're going to be installing the Draw-Tite Sport Frame trailer hitch receiver. This is a custom fit class one with an 1-1/4" opening. Part number is 24899. This is what your hitch will look like once we've got it installed in the vehicle. Now now we're going to go over a few measurements. These are going to help you in selecting a ball mount, bike rack, or any other accessory you might want to add to your hitch. more
2/5/2015 1:31:51 PM
Trailer Hitch Installation - 2007 Acura TL - Hidden Hitch- Video
Today, on our 2007 Acura TL, we're going to be installing the Hidden Hitch Trailer Hitch Receiver, part number 60814. Here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch, such as a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is approximately 6 inches. From the top of the opening in the receiver to the ground is approximately 10 1/2 inches. Now, let's go ahead and install our hitch. Now, to begin our installation, we're going to first need to raise the rear hatch of the trunk of the vehicle. We'll then need to clear out anything that may be in the trunk, as far as coverings, as well as remove the spare tire. more
12/15/2014 1:44:36 PM
Trailer Hitch Installation - 2007 Acura TL - Draw-Tite- Video
Today on our 2007 Acura TL, we're going to be installing the Draw-Tite Trailer Hitch Receiver, part number 24755. Now, here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch such as a bicycle rack or a cargo carrier. From the center of the hitch pinhole to the outermost edge of the bumper is approximately six inches. From the top of the opening in the receiver to the ground is approximately ten and a half inches. Now, let's go ahead and install our hitch. Now to begin our installation, we're going to first need to raise the rear hatch of the trunk of the vehicle. more
12/15/2014 1:39:19 PM
Trailer Hitch Installation - 2013 Acura RDX - Curt- Video
Today on this 2013 Acura RDX, we're going to install part number C13130 from Curt. First we'll go underneath the vehicle and show you where attachment points are. There's a threaded hold at the very end of the frame and an existing hole going up towards the front. This will be the same on both sides. Next we'll show you the hardware that works with the hitch. On our threaded hole in the frame, it will have a metric bolt and it will get a conical-tooth washer. Make sure your teeth on the conical-tooth washer always face towards the hitch. For the open hole going up towards the front of the vehicle, we'll get a handle nut. more
11/19/2014 1:51:50 PM
Trailer Hitch Installation - 2014 Acura RDX - Curt- Video
Today on our 2014 Acura RDX were going to be installing the Curt Trailer Hitch Receiver, part number C12083. Now heres what our hitch looks like installed on our vehicle. Now well go ahead and give you a couple measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is approximately 4-1/2 inches. From the top of the opening in the receiver to the ground is approximately 13-1/2 inches. Now lets go ahead and install our hitch. Were going to begin first by pointing out our mounting locations. Well start here at the passenger side. more
9/23/2014 12:14:54 AM
Trailer Hitch Installation - 2014 Acura MDX - Curt- Video
Today on our 2014 Acura MDX, we'll be installing the Curt 2 inch receiver tube hitch, part number C13146. This is what our hitch will look like, once installed. Next, we'll go ahead and give you a couple of measurements, to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 2 3/4 inches. From the top of the receiver tube opening to the ground is 14 inches. This will assist you selecting accessories such as a ball mount, bike rack, or cargo carrier. Now, we will go ahead with installation. more
12/10/2013 8:52:58 AM
Trailer Hitch Installation - 2005 Acura MDX - Hidden Hitch- Video
Today on our 2005 Acura MDX well be installing Hidden Hitch part number 87454. This is what our hitch will look like once its installed. Next were going to give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 3 inches. From the top of the receiver tube opening to the ground is 18-3/4 inches. This will assist you with selecting accessories such as a ball mount, bike rack or cargo carrier. more
6/14/2013 1:50:43 PM
Trailer Hitch Installation - 2005 Acura MDX - Draw-Tite- Video
Today, on our 2005 Acura MDX, well be installing the Draw-Tite Hitch, Part Number 75599. This is what our hitch to look like once its installed. Next, well go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch.From the center of the hitch pinhole to the outermost edge of your bumper is 3 inches. From the top of the receiver tube opening to the ground is 18-3/4 inches. This will assist you in selecting accessories such as a ball mount, bike rack or a cargo carrier.Now, well go ahead with the installation. To begin our install, well first go ahead and lower our exhaust. more
6/14/2013 1:45:39 PM
Trailer Hitch Installation - 2013 Acura RDX - Draw-Tite- Video
Today on this 2013 Acura RDX were going to install part number 75692 from Draw Tite. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 14 inches. From the center of the hitch pin hole to the edge of the bumper will be about four and a half inches. Now well go ahead and show you how the hitch is installed. more
1/16/2013 12:26:24 PM
Trailer Hitch Installation - 2012 Acura MDX - Draw-Tite- Video
All right, today on this 2012 Acura MDX were going to install part #: 75614 from Draw-Tite. All right, this is what the hitch looks like once its installed on the vehicle. Next well give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 16 and a quarter inches and from the center of the hitch pinhole to the edge of the bumper will be three and three quarter inches. Now Ill go ahead and show you how the hitch is installed. First thing that we need to do is go ahead and lower the spare tire and get it out of our way. more
12/17/2012 11:59:30 AM
Trailer Hitch Installation - 2012 Acura MDX - Curt- Video
Today, on this 2012 Acura MDX, we are going to install part number 13354 from Curt. All right, this is what the hitch will look like once its installed on the vehicle. Next, we will go ahead and give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 17 inches and from the center of the hitch pin hole to the edge of the bumper will be 3-1/2 inches.Now, Ill go ahead and show you how the hitch is installed. First thing we need to do is go ahead and lower the spare tire and get it out of our way. Then, next we will go ahead and lower the exhaust by removing the two rear most rubber hangers. more
12/16/2012 11:58:45 PM
Trailer Hitch Installation - 2013 Acura ILX - Curt- Video
Today on our 2013 Acura ILX well be installing the Curt hitch, part number 11437. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is two and a half inches. From the top of the receiver tube to the ground is 10 inches. This will assist you with selecting accessories such as a bike rack or a cargo carrier. more
11/8/2012 10:40:33 AM
Trailer Hitch Installation - 2006 Acura TL - Hidden Hitch- Video
Today on our 2006 Acura TL well be installing Hidden Hitch, part number 60814. This is what our hitch will look like once its installed. Next well go ahead and take a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is six and a half inches. From the top of the receiver tube to the ground is nine and three quarter inches. This will assist you with selecting accessories such as a bike rack or cargo carrier.Now let go ahead with installation. more
11/5/2012 1:28:24 PM
Trailer Hitch Installation - 2006 Acura TL - Draw-Tite- Video
Today on our 2006 Acura TL well be installing the Draw Tite hitch, part number 24755. This is what our hitch will look like once its installed. Next well go ahead and take a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is six and a half inches. From the top of the receiver tube to the ground is nine and three quarter inches. This will assist you with selecting accessories such as a bike rack or cargo carrier.Now let go ahead with installation. more
11/5/2012 1:27:36 PM
Trailer Hitch Installation - 2010 Acura MDX - Draw-Tite- Video
Today on our 2010 Acura MDX were going to install part number 75614 from Draw Tite. This is what the hitch looks like when its installed on the vehicle. Next well go ahead and give you some measurements to help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carier. From the center of the hitch pin hole to the edge of the bumper will be three and three quarter inches, nd from the top of the receiver opening down to the ground will be 16 niches.Now well go ahead and show you how the hitch is installed. First thing were going to do is go ahead and we removed the spare tire. With our tire out fo the way we can see whats going on and make it a little easier to install everything. more
11/5/2012 11:16:24 AM
Trailer Hitch Installation - 2011 Acura MDX - Draw-Tite- Video
Today on our 2011 Acura MDX, we'll be installing the Draw-Tite Hitch, part number 75614. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/2 inches. From the top of the receiver tube to the ground is 16 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier. more
9/24/2012 2:20:40 PM
Trailer Hitch Installation - 2011 Acura MDX - Curt- Video
Today on our 2011 Acura MDX, we'll be installing the Curt Hitch, part number 13354. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4-3/4 inches. From the top of the receiver tube to the ground is 16-1/4 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier. more
9/24/2012 2:18:55 PM
Trailer Hitch Installation - 2012 Acura RDX - Curt- Video
Today on our 2012 Acura RDX, well be installing Curt Hitch, part number C13154. Before we start our installation, here are a few measurements that will assist you when selecting accessories, such as a draw bar, a bike rack or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 5 inches, and from the top of the reciver tube to the ground is 12 inches. Now, lets go ahead with our install. Now, to begin our installation, well go ahead and point out the connection points on the frame of the vehicle. On the passenger side at the rearmost point is a weld nut, here, and well be using this hole here for our frontmost attachment. more
8/21/2012 4:12:51 PM
Trailer Hitch Installation - 2012 Acura RDX - Hidden Hitch- Video
Today on our 2012 Acura RDX, well be installing Hidden Hitch, part number 87584. Now, before we start our installation, here are some measurements to help in selecting accessories, such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 4 inches, and from the top of the receiver tube to the ground is 12 inches. Now, lets go ahead with our install. To begin our installation, well go ahead and point out the connection points on the frame of the vehicle. On the passenger side, at the rearmost point, is a weld nut, here, and well be using this hole here for our frontmost attachment. more
8/21/2012 4:12:16 PM
Trailer Hitch Installation - 2012 Acura RDX - Draw-Tite- Video
Today on our 2012 Acura RDX, well be installing Draw-Tite Hitch, part number 75692. Now, before we start our installation, here are some measurements to help you in selecting accessories such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 4 inches, and from the top of the receiver tube to the ground is 12 inches. Now, lets go ahead with our install. To begin in our installation, well go ahead and point out the connection points on the frame of the vehicle. On the passenger side, at the rear most point, is a weld nut here, and well be using this hole here for our frontmost attachment. more
8/21/2012 4:11:40 PM
Trailer Hitch Installation - 2008 Acura MDX - Curt- Video
Today on our 2008 Acura MDX, we'll be installing the Curt Hitch, part number 13354. Here are a couple measurements that will assist you in selecting accessories for your new hitch such as a drawbar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4 inches. From the top of the receiver tube to the ground is 16 inches. Now, let's go ahead with the installation. Before we begin our installation, we've already gone ahead and removed the spare tire. more
8/6/2012 3:03:43 PM
Trailer Hitch Installation - 2012 Acura TL - Hidden Hitch- Video
Today on this 2012 Acura TL, we're going to install part number 60236 from Hidden Hitch. Alright, first thing we're going to do is go ahead and lower the exhaust. Grab the two rubber hangers on each side; we're going to spray now some lubricant to make it a little easy to remove. On the driver's side, we're going to unbolt the muffler, to get a better view of what is going on. Now, you're not going to have to do this on the actual install. Okay, on the passenger side, we find out that we can a little more room, if we remove the third hanger going towards the front. more
6/11/2012 10:06:23 AM
Trailer Hitch Installation - 2012 Acura TL - Draw-Tite- Video
Alright, today on this 2012 Acura TL, we're going to install part number 24834 from Draw-Tite. Alright, first thing we're going to do is go ahead and lower the exhaust. Grab the two rubber hangers on each side; we're going to spray now some lubricant to make it a little easy to remove. On the driver's side, we're going to unbolt the muffler, to get a better view of what is going on. Now, you're not going to have to do this on the actual install. Okay, on the passenger side, we find out that we can a little more room, if we remove the third hanger going towards the front. more
6/11/2012 10:05:41 AM
Trailer Hitch Installation - 2009 Acura MDX- Video
Today on this 2009 Acura MDX were going to install part number 13354 from Curt. This is what the hitch looks like when it is installed on the vehicle. Next well give you some measurements that will help you out in selecting accessories such as a ball mount, bicycle rack, or a cargo carrier. From the center of the pin hitch hole to the outside edge of the bumper on this vehicle is going to be 3-1/2 inches, and from the top of the receiver opening down to the ground is going to be 17 inches. Now we will go ahead and show you how the hitch is installed. A couple of steps we need to take care of first is that we remove the spare tire to make it easier to install, and also we are going to lower the exhaust, and also remove the heat shields. more
10/21/2011 12:55:35 PM
Trailer Hitch Installation - 2007 Acura MDX- Video
Today on this 2007 Acura MDX, we are going to be installing Curt hitch part number C13354. Before we get started with our hitch installation, we are going to go ahead and show you a couple of the final install dimensions, which will help choosing your hitch accessories a little bit easier. From the top of the receiver tube opening to the ground is going to measure 16-1/2 inches and from the center of the pin hole to the clear end of the bumper is going to measure approximately 4 inches. Okay, let us go ahead and move on to our installation. 0:26 more
9/30/2011 4:40:44 PM
Trailer Hitch Installation - 2010 Acura MDX- Video
Today on this 2010 Acura MDX we are going to install part number 13354 from Curt. First thing we need to do to get started is lower the spare tire. It makes everything a lot easier to thread the bolts in and tighten them down. The next thing we want to do is lower the exhaust. There is going to be two rubber hangers on each muffler so we are going to spray them down with some lubricant and then pry them off any way we can and then we will get to installing the hitch. You will notice that when we took down the first bumper hanger it came down pretty good already so it might be a good idea to run a strap around the exhaust components to keep them from falling down. Lets move on over to the rubber hanger. Spray it down and remove it. 00:38 more
7/12/2010 1:03:08 PM
Trailer Hitch Installation - 2006 Acura MDX- Video
Today on this 2006 Acura MDX, we are going to install Draw-Tite hitch, part number 75599. This installation will also apply for the Hidden Hitch part number, 87454. We are underneath the vehicle, looking at the passenger side frame rail. I am going to go ahead and point out the mounting holes that we are going to be using to install the trailer hitch. As you can see here, we have three existing weld nuts here at the end of the frame, we will be using these three as our attaching points for our trailer hitch. :24 more
4/1/2010 11:00:45 AM
Trailer Hitch Installation - 2002 Acura RSX- Video
Today we are going to be installing hitch part number 24719 from Draw-Tite on a 2002 Acura RSX. The first thing we are going to need to do is to go inside the trunk and remove the spare tire from the spare tire well. We will be drilling two holes into the spare tire well to help hold the hitch up into place. In doing so, there some models that have an aftermarket subwoofer here. If your application does have this, you will need to actually disconnect the wiring harness here on the side by depressing the tab the on the forward side. And then from there you can just remove the center portion and then lift the subwoofer out of position and then remove the spare tire. more
5/11/2009 6:17:16 AM
Filter Videos
Filter Videos
