Trailer Hitch Installation - 2005 Honda Odyssey - Curt C12031- Video
Today on our 2005 Honda Odyssey we'll be installing the Curt Trailer Hitch Receiver in a Class II with an inch and a quarter opening, part number C12031. Here's what the hitch looks like installed on our vehicle. Now we'll give you a couple of measurements in helping you choose accessories for your hitch, such a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pinhole to the outermost edge of the bumper is approximately two and a half inches. From the top of the opening in the receiver to the ground is approximately thirteen inches. Now let's go ahead and install our hitch. To begin with, we'll go ahead and install our safety strap. This will support the exhaust once we remove two exhaust hangers so we can gain access to our weld mounts on the passenger side. Now that our safety strap is in place, we'll go ahead and use a little spray lubricant and a pry bar to work the two exhaust hangers off. Once the exhaust hangers are loose, we can go ahead and lower the exhaust down enough to give us a little bit more access to our two weld nuts on the passenger side. We'll be using a total of four weld nuts, two weld nuts on each side and one carriage bolt and spacer block that will be fish wired in on the driver's side. We'll go ahead and clean the weld nuts out using a bit of spray lubricant and a half inch nylon tube brush, which is part number 814092. Once we have all four of the weld nuts cleaned out now we can go ahead and use our fish wire to put our carriage bolt and spacer block into place. more
10/2/2013 3:06:21 PM
Trailer Hitch Installation - 2010 Honda Odyssey - Curt- Video
Today, on this 2010 Honda Odyssey, we're going to install part #C12031 from CURT. This is what the hitch looks like on the Odyssey. We'll give you a few measurements to help you with selecting some accessories, such as a bicycle rack or a cargo carrier. The top of the receiver opening down to the ground will be about 14 inches, and the center of the center of the hitch-pin hole to the edge of the bumper will be about 3 inches. Now, I'll show you how to hitch and install. First, we need to check our attachment points underneath the vehicle. There's going to be two threaded holes toward the bumper on each side. We're going to spray some lubricant and use a tube brush to help clean up the threads. The tube brush is part #814092. Take a few moments to scrub down your threads. Then test it with one of the hitch-bolts to make sure the thread is in okay. Once we can thread it in, we can move on to the next one. There will be 4 threaded holes that we have to clean out. Now, we can show you how the hardware works with the hitch. With the hitch off the vehicle, we'll show you how the bolts will work with the fasteners. more
10/2/2013 11:44:57 AM
Trailer Hitch Installation - 2010 Honda Odyssey - Hidden Hitch- Video
Today on our 2010 Honda Odyssey we're going to install part number 90153 from Hidden Hitch. Alright this is what the hitch looks like installed on the van. Next we'll give you some measurements to help you out selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about twelve and a quarter inches. And from the center of the hitch pin hole to the edge of the bumper will be about four and a half inches. Alright, now we'll go ahead and show you how the hitch is installed. To start off our install, we'll go ahead and locate the threaded holes at the bottom of the frame located right behind the bumper. Our next step is to go ahead and clean them out. We're going to use some spray lubricant and a tube brush to help clean out the threads. The tube brush is going to be part number 814092. We'll go ahead and test it with one of the hitch bolts, and once we can thread in the bolt we'll be okay. We go ahead and show you how the hardware works in the hitch and goes into the weld nuts. more
10/2/2013 8:48:57 AM
Trailer Hitch Installation - 2010 Honda Odyssey - Draw-Tite- Video
Today on a 2010 Honda Odyssey, we're going to install Part Number 36417 from Draw-Tite. This is what the hitch looks like once installed on the van. Next, we'll give you some measurements to help you out with selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 12-1/4 inches. From center of the hitch pin hole to the edge of the bumper will be about 4-1/2 inches. Now, we'll go ahead and show you how the hitch is installed. To start off our install, we'll go ahead and locate the threaded holes at the bottom of the frame. more
10/2/2013 8:48:39 AM
Trailer Hitch Installation - 2010 Honda Odyssey - Curt C13068- Video
Today on this 2010 Honda Odyssey were going to install part #: C13068 from Curt. This is what the hitch looks like once installed on the van. Next, well give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be around 14 inches and from the center of the hitch pinhole to the edge of the bumper will be around four and a quarter inches. Now well go ahead and show you how the hitch is installed. First up, we have to go ahead and look for the mounting points underneath the van. more
10/1/2013 1:19:49 PM
Trailer Hitch Installation - 2013 Honda Odyssey - Hidden Hitch- Video
Today on this 2013 Honda Odyssey, were going to install part #87479 from Hidden Hitch. This is what the hitch looks like once its installed on the vehicle. Next, well give you some measurements to help you out in selecting some accessories, such as a bicycle rack, a ball mount, or a cargo carrier. From the top of the receiver opening down to the ground will be about 12 inches. From the center of the hitch pinhole to the edge of the bumper will be about 6-1/2 inches. Now, well go ahead and show you how the hitch is installed. more
11/19/2012 10:45:42 AM
Trailer Hitch Installation - 2013 Honda Odyssey - Draw-Tite 36417- Video
Today on this 2013 Honda Odyssey, were going to install part #36417 from Draw-Tite. This is what the hitch looks like once its installed on the vehicle. Next, well give you some measurements to help you out in selecting some accessories, such as a bike rack or a cargo carrier. From the top of the receiver opening down to the ground will be 11-3/4 inches. From the center of the hitch pinhole to the edge of the bumper will be about 5-1/4 inches. Now, well go ahead and show you how the hitch is installed. more
11/19/2012 10:45:31 AM
Trailer Hitch Installation - 2008 Honda Odyssey - Hidden Hitch- Video
Today on this 2008 Honda Odyssey were going to install part number 87479 from Hidden Hitch. This is what the hitch looks like when its installed on the van. Next well give you some measurements that will help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 12 inches. From the center of the hitch pin hole to the edge of the bumper will be about five and a quarter inches. Now Ill go ahead and show you how the hitch is installed. more
11/8/2012 10:38:27 AM
Trailer Hitch Installation - 2008 Honda Odyssey - Draw-Tite- Video
Today on this 2008 Honda Odyssey were going to install part number 75270 from Draw Tite. This is what the hitch looks like when its installed on the van. Next well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 12 inches. From the center of the hitch pin hole to the edge of the bumper will be about five and a quarter inches. Now Ill go ahead and show you how the hitch is installed. more
11/8/2012 10:37:25 AM
Trailer Hitch Installation - 2013 Honda Odyssey - Curt C13068- Video
Today on our 2013 Honda Odyssey well be installing Curt Hitch, part number C13068. This is what our hitch will look like once its installed. Next, well go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 5 inches. From the top of the receiver tube to the ground is 12 inches. This will assist you in selecting accessories such as a drawbar, a bike rack or a cargo carrier. more
10/12/2012 11:58:46 AM
Trailer Hitch Installation - 2009 Honda Odyssey - Curt- Video
Today on our 2009 Honda Odyssey, we're gonna be installing the Curt hitch part number C12031. This is what a hitch looks like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 3 inches. From the top of the receiver tube to the ground is 13 and 3/4 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier. more
9/7/2012 1:59:28 PM
Trailer Hitch Installation - 2009 Honda Odyssey - Hidden Hitch- Video
Today on our 2009 Honda Odyssey, we're gonna be installing the hidden hitch part number 90153. Before we begin installation, we'll go ahead and lower the exhaust. To lower the exhaust, we'll use a little spray lubricant on the rubber isolator for the rear exhaust hanger. Then we can simply take our crowbar and just remove the isolator from the metal hanger. This point, we can go ahead and point out then attach the points here in the frame. Next, we'll go ahead and take our half-inch nylon tube brush part number 814092 and some spray lubricant to clean up the weldnuts in the frame. more
9/7/2012 12:26:09 PM
Trailer Hitch Installation - 2009 Honda Odyssey - Draw-Tite- Video
Today on our 2009 Honda Odyssey, we'll be installing a draw-tite hitch part number 36417. Before we begin installation, we'll go ahead and lower the exhaust. To lower the exhaust, we'll use a little spray lubricant on the rubber isolator for the rear exhaust hanger. Then we can simply take our crowbar and just remove the isolator from the metal hanger.This point, we can go ahead and point out then attach the points here in the frame. Next, we'll go ahead and take our half-inch nylon tube brush part number 814092 and some spray lubricant to clean up the weldnuts in the frame. After you finish cleaning up the weldnut, I recommend you to take the 12mm bolts and go ahead and drive it in to the weldnut to make sure it goes nice and smoothly. more
9/7/2012 12:25:35 PM
Trailer Hitch Installation - 2011 Honda Odyssey - Hidden Hitch- Video
Today in our 2011 Honda Odyssey, well be installing a hidden hitch, part number 90153. This is what our hitch well look like once its installed. Next, well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outer most edge of the bumper is 5-1/4 inches. From the top of the receiver tube to the ground is 11-3/4 inches. This will assist you in selecting accessories such as a drawbar, a bike rack or a cargo carrier. more
8/9/2012 10:49:32 AM
Trailer Hitch Installation - 2011 Honda Odyssey - Draw-Tite- Video
Today in our 2011 Honda Odyssey, well be installing a draw type hitch, part number 36417. This is what our hitch well look like once its installed. Next, well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outer most edge of the bumper is 5-1/4 inches. From the top of the receiver tube to the ground is 11-3/4 inches. This will assist you in selecting accessories such as a drawbar, a bike rack or a cargo carrier. more
8/9/2012 10:48:47 AM
Trailer Hitch Installation - 2011 Honda Odyssey - Curt- Video
Today on our 2011 Honda Odyssey well be installing the Curt Hitch part number C13068. This is what our hitch will look like once its installed. Next, well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 5 inches. From the top of the receiver tube to the ground is 12-3/4 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier. more
8/8/2012 12:41:07 PM
Trailer Hitch Installation - 2011 Honda Odyssey - Curt C12031- Video
Today on our 2011 Honda Odyssey well be installing the Curt Hitch part number C12031. This is what our hitch will look like once its installed. Next, well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 4-1/2 inches. From the top of the receiver tube to the ground is 12-3/4 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier. more
8/8/2012 12:39:59 PM
Trailer Hitch Installation - 2010 Honda Odyssey - Draw-Tite 75270- Video
Today in our 2010 Honda Odyssey were going to be installing the Draw-Tite Hitch part number 75270. This is what our hitch is going to look like once its installed. Now here are a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to outermost edge of the bumper is 5 inches. From the top of the receiver tube to the ground is eleven inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier. more
7/18/2012 12:24:47 PM
Trailer Hitch Installation - 2007 Honda Odyssey - Hidden Hitch 87479- Video
Today in this 2007 Honda odyssey will be installing a hidden hitch part number 87479. Next well go ahead and give you a couple of measurements this is what are hitch looks like once it is installed from the center of a hitch pin hole to the outermost edge of the bumper is 5 inches from the top of the receiver tube to the ground is 12 and three quarter inches this will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier now lets go ahead with the installation our first step is going to be to lower the exhaust there are two rubber ice slathers that it need to be remove to o this well first spray them down with some spray lubricant and then remove the rubber from the ice hanger. Alright now with the exhaust hangers remove well now move on to our attachment points were going to have three on each sides. Each of this attachment points will be a well nut in the frame heres a rear most of the attachment points are center and the forward most attachment points. Before we try and install our hitch and new hardware. We want to go ahead and clean each one of this well nut out over time theyll build up with dirt, dust and debris and become corroded with rust. more
4/17/2012 10:27:19 AM
Trailer Hitch Installation - 2007 Honda Odyssey - Draw-Tite 75270- Video
Today in this 2007 Honda Odyssey we will be installing the Draw-Tite hitch part number 75270. Next we will go ahead and give you a couple of measurements this is what are hitch looks like once it is installed from the center of a hitch pin hole to the outermost edge of the bumper is 5 inches from the top of the receiver tube to the ground is 12 and three quarter inches this will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier now lets go ahead with the installation our first step is going to be to lower the exhaust there are two rubber ice slathers that it need to be remove to o this well first spray them down with some spray lubricant and then remove the rubber from the ice hanger. Alright with the exhaust hangers remove well now move on to our attachment points were going to have three on each sides. Each of this attachment points will be a well nut in the frame heres a rear most of the attachment points are center and the forward most attachment points. Before we try and install our hitch and new hardware. We want to go ahead and clean each one of this well nut out over time theyll build up with dirt, dust and debris and become corroded with rust. more
4/17/2012 5:26:17 AM
Trailer Hitch Installation - 2012 Honda Odyssey - Hidden Hitch- Video
Today on our 2012 Honda Odyssey, were going to install the Hidden Hitch, part number 87479. All right, this is what it will look like with the hitch installed. Now we'll go ahead and give you a couple of measurements that will assist you in selecting accessories for your new hitch such as a draw bar, a bike rack or a cargo carrier. From the center of the hitch pinhole to the outermost point of the bumper is 6 inches. From the top of the receiver tube to the ground is 11 1/2 inches.Now lets go ahead with the installation. Our first step is actually to remove the underbody trim panel here on the driver side. more
3/27/2012 3:42:57 AM
Trailer Hitch Installation - 2012 Honda Odyssey - Draw-Tite 75270- Video
Today on our 2012 Honda Odyssey, were going to install the Draw-Tite Hitch, part number 75270. All right, this is what it will look like with our hitch installed. Now Ill go ahead and give you a couple of measurements that will assist you in selecting accessories for your new hitch such as a draw bar, a bike rack or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 6 inches. From the top of the receiver tube to the ground is 11 1/2 inches. Now lets go ahead with the installation. more
3/27/2012 3:42:42 AM
Trailer Hitch Installation - 2012 Honda Odyssey - Curt- Video
3/26/2012 7:28:09 AM
Trailer Hitch Installation - 2012 Honda Odyssey - Curt C12031- Video
Today on our 2012 Honda Odyssey, were going to install the Curt Hitch, part number C12031. This is what the hitch will look like once its installed. Heres a couple of measurements that will assist you in selecting accessories for your new hitch such as a draw bar, a bike rack, or cargo carrier. From the center of the hitch pinhole to the outermost point of the bumper is 4 inches. From the top of the receiver tube to the ground is 12 3/4 inches. Now, lets go ahead with the installation. more
3/26/2012 7:16:37 AM
Trailer Hitch Installation - 2012 Honda Odyssey - Hidden Hitch 90153- Video
Today on our 2012 Honda Odyssey were going to install the Hidden Hitch part number 90153. This is what it will look like with our hitch installed. Now well go ahead and give you a couple of measurements that will assist you with selecting accessories for your new hitch such as a drawbar, a bike rack or a cargo carrier. From the center of the hitch pin hole to the outermost point of the bumper is 5-3/4 inches. From the top of receiver tube to the ground is 11-1/2 inches. Now lets go ahead with the installation. more
3/26/2012 7:14:54 AM
Trailer Hitch Installation - 2012 Honda Odyssey - Draw-Tite 36417- Video
3/26/2012 7:11:34 AM
Trailer Hitch Installation - 2011 Honda Odyssey- Video
Today on this 2011 Honda Odyssey, were gonna install part number 87479 from Hidden Hitch. This also applies for part number 75270 from Draw-Tite.This is what the hitch looks when its installed on a van. Next, were go ahead and produce measurements that will help you out in selecting some accessories such as the ball mount, the bicycle rack or cargo carrier. From the center of the hitch pin hole to the outside edge of the bumper is going to be 6 inches and from the top of the receiver down to the ground is going to be 12 inches. Alright, now were gonna show you how the hitch is installed.First thing you need to do is get underneath the vehicle and remove this panel right here. Theres gonna be four fasteners for the panel itself and therell be a fifth one that goes through the panel and the mudflap. more
12/8/2011 2:28:44 PM
Trailer Hitch Installation - 2002 Honda Odyssey- Video
Today we are working on a 2002 Honda Odyssey. Were going to install Hidden Hitch, part number 87479. This will also be comparable to the Draw Tite Hitch part number 75270. Here are a couple measurements that will assist you in selecting accessories for a new hitch, such as a bike rack, cargo carrier, or a draw bar. From the center of the hitch pin hole to the outer most part of the bumper is 5 inches. more
10/12/2011 5:07:40 PM
Trailer Hitch Installation - 2007 Honda Odyssey - Curt c13068- Video
Today on this 2007 Honda Odyssey we're going to be installing Curt Hitch part number C13068. Starting off over here on the drivers side of the vehicle, we're going to be using three attaching points. We're going to be using the two rear most weld nuts here at the end of the frame. And if you follow a little bit forward you see we've got three existing holes. We're going to be using the middle one as our third and final attaching point. And that's going to be the same on the passenger's side of the vehicle. more
10/11/2011 4:58:38 AM
Trailer Hitch Installation - 2003 Honda Odyssey- Video
Today on this 2003 Honda Odyssey we are going to install part number 87479 from Hidden Hitch. This will also apply to part number 75270 from Draw-Tite. Alright, this is what the hitch looks like when it is installed on the vehicle. Next we will give you some measurements that will help you out in ing some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground on this particular vehicle is going to be 12 inches. And from the center of the hitch pin hole to the outside edge of the bumper is going to be 4-1/2 inches. Now we will go ahead and show you how it gets installed. 0:33 more
9/1/2011 3:26:01 PM
Trailer Hitch Installation - 2000 Honda Odyssey- Video
Today on this 2000 Honda Odyssey, we are going to be installing Hidden Hitch part number 87479. And this installation will also apply for Draw-Tite hitch part number 75270. OK, we are underneath the vehicle and we are looking actually at the driver side frame rail. We want to go ahead and point out the mounting holes we are going to be using to attach our trailer hitch. You will notice that we have multiple holes here in the bottom of the frame. We are going to be using three of the existing weld nuts here on the bottom of the frame to attach the hitch. We are going to use the two here at the rearmost portion of the frame and if you follow forward, we are going to use one at the forward side. Alright, and that is going to be the same on the passenger side as well. 0:34 more
5/13/2010 9:22:47 AM
Trailer Hitch Installation - 1999 Honda Odyssey- Video
Today on this 1999 Honda Odyssey we are going to be installing part number 87479. This installation will also apply to part number 75270. The first thing that we are going to need to do is we are going to have to lower the exhaust from the exhaust mount in the rear of the vehicle on the passenger side and the one up towards the middle which is the second to last one. And it helps to have a strap to mount on the bottom of the vehicle, underneath the exhaust, to hold it up to keep from damaging the rest of the exhaust further up from the vehicle. So, if you can not find any mounting spots for your strap, you can probably just go ahead and use the existing rear springs. You want to just loosen it up enough to where you have a little bit of play so you can at least move around the exhaust to take it off the hanger. You can go ahead and tighten the strap to keep the exhaust from hanging down further than necessary. 0:50 more
4/27/2010 7:23:58 AM
Trailer Hitch Installation - 2008 Honda Odyssey - Draw-Tite 36417- Video
Today we are going to be installing hitch part number 36417 from Draw-Tite on a 2008 Honda Odyssey. We are underneath the vehicle now and we are looking at the driver's side frame rail. As you can see here at the end, we have two existing weld nuts in the frame that we are going to be using as the two attaching points for the trailer hitch. And then over here on the passenger's side, we have the same two weld nuts that are also going to provide the attaching points. And you can see, we do have the exhaust in the way, so we are going to want to lower that down first. To do that, we are going to remove it off of the rubber hanger here at the rear position and then here at the more forward position, almost in the middle of the vehicle. more
5/27/2009 10:19:39 AM
Filter Videos
Filter Videos
