Trailer Hitch Installation - 2012 Subaru Outback Wagon - Curt 13390- Video
Today on our 2012 Subaru Outback Wagon, we will be taking a look at and installing the Curt Custom Fit Class 3 trailer hitch receiver, part number 13390. We'll give you a few measurements to help you in selecting some hitch accessories, such as ball mounts, bike racks, and cargo carriers. From the top of the receiver tube to the ground is going to be about 14". From the center of the pin hole to the outermost edge of the bumper is going to be about 2 1/2". Here's what our hitch is going to look like once it's installed. It's going to have that nice round bar design and it's going to be nice and sleek against the back end of the vehicle with that black powder coat finish to help prevent any kind of rust and corrosion. With it's fully welded design, it's going to be nice and sturdy, offering a 600 pound tongue weight capacity and 4000 pound towing capacity with it's 2" by 2" receiver tube opening and plate steel design. It's going to have a 5/8" pin hole going straight through the center. more
12/22/2015 8:36:06 AM
Trailer Hitch Installation - 2015 Subaru Forester - Curt- Video
Today in our 2015 Subaru Forester, well be installing the Curt 1-1/4-inch receiver tube hitch, part number C12100. Now, note. Were going to be working on a vehicle with a single rear exhaust system. If you have a dual rear exhaust system, you have to compensate by removing additional hangers. Well also go ahead and note this process we do here on one side is going to get repeated identically on the opposite side as our attachments are the same for each side.Heres what our hitch is going to look like once installed. Next, Ill give you a couple of measurements to assist you in selecting accessories for your new hitch. more
12/15/2015 11:45:41 AM
Trailer Hitch Installation - 2016 Subaru Forester - Draw-Tite 75876- Video
Today on our 2016 Subaru Forester we're taking a look at and installing the Draw Tite Max Frame Class 3 trailer hitch receiver, part # 75876. You have that nice sleek tuck design where it's going to be underneath the back side of the vehicle where it really isn't going to be visible. The only thing you're really going to see from the back end is going to be that receiver tube. You're going to have a fully welded design with a black powder coat finish. It's going to help prevent any kind of rust and corrosion. Also plate steel brace across the bottom which is also going to double as your chain tie down on either side. more
12/14/2015 3:04:59 PM
Trailer Hitch Installation - 2016 Subaru Forester - Curt- Video
Today on our 2016 Subaru Forester, we'll be taking a look at and installing the Curt custom fit class 2 trailer hitch receiver, part number C12100. Here's what a hitch is going to look like once it's installed. You're going to see it's going to be nice and tucked away underneath the back side of the vehicle with only the chain tie downs and our receiver tube really being visible from that back side. Now this is going to be your class 2 receiver hitch coming with a fully welded design, black powder coat finish to resist any kind of rust and corrosion and it's going to have a 350 pound tongue weight capacity and 35 hundred pound towing capacity. Remember it's got a half inch pin hole going straight through so you can secure your items down that you have on the back end. You can see that into that receiver tube, it's almost going to be out to the back of the bumper so you won't have to worry about having anything that's going to come to close to the back side of the vehicle when you place in any items on the back. Whether that be a cargo carrier, a ball mount, or even a bike rack. Now I'll go ahead and give you a few measurements to assist you in selecting from hitch accessories. more
12/10/2015 3:33:51 PM
Trailer Hitch Installation - 2016 Subaru Outback Wagon - Draw-Tite 75673- Video
Today on our 2016 Subaru Outback wagon we're going to take a look at and show you how to install the Draw-Tite Max-Frame trailer hitch receiver. This is a custom fit class three hitch. Its part number is 75673. Here's what the hitch is going to look like installed. It's going to give us a nice symmetrical look right here on the backside of the vehicle. This is a class three so of course we're going to have the 2" by 2" reciever tube opening. more
12/2/2015 12:16:32 PM
Trailer Hitch Installation - 2015 Subaru XV Crosstrek - Draw-Tite- Video
Today on our 2015 Subaru XV Crosstrek, we're going to be taking a look at and installing our Draw Tite Support Frame Class I Trailer Hitch Receiver, part number 24886.Speaker 2: Now here's what our trailer hitch is going to look like once it's installed on our vehicle. It's going to have that nice, clean, sleek look across the back, with that black powder coat finish to help prevent any kind of rust and corrosion, as well as a fully welded design. It's going to have your chain tie-downs on either side, and your inch and a quarter by inch and a quarter receiver tube with a 200 pound tongue weight capacity and 2,000 pound towing capacity. It's going to have that half inch hole going straight through with that plate steel design over the to to add that extra strength on the end of your tongue. Now we'll go ahead and give you a few measurements to help you in selecting hitch accessories. From the top of the receiver tube to the ground, it's going to be about 15 inches. From the center of the panel to the outer most part of the bumper, it's going to be about two and three quarter inches. This will assist you in selecting for bike racks and cargo carries. We'll go ahead and take a safety strap and put it up over the bottom side of the frame, that way when we drop down our exhaust, it doesn't fall under its own weight. more
11/24/2015 11:56:34 AM
Trailer Hitch Installation - 2006 Subaru Tribeca - Draw Tite- Video
Today on our 2006 Subaru Tribeca, we're going to be taking a look at and installing the Draw-Tite Class Three 2 inch receiver hitch, part number 75401. Now you can see e have our hitch installed and it's going to be a nice sleek look on the back of the vehicle. It's also going to come out far enough to where you can place your items on the back side without making contact with that back bumper. With it extending out and away from the vehicle a little bit. You're going to have a 2 inch by 2 inch receiver tube. Your chain tie downs on either side as well as your 5/8 inch pinhole straight through with the j-pin style holes here in the front. more
8/24/2015 11:21:28 AM
Trailer Hitch Installation - 2015 Subaru Forester - Draw-Tite- Video
Today on our 2015 Subaru Forester we're going to take a look at and show you how to install the Draw-Tite Max-Frame trailer hitch receiver. This is a custom fit class III hitch, its part number is 75876. Here's what our hitch is going to look like once we get it installed. Nice narrow visual here on the back, you don't see a whole lot of it going off of each side. It's tucked up nicely underneath the bumper so we won't have to worry about any kind of knee hits or anything like that. We've got the round tube design, 2-inch by 2-inch opening, of course. Something that's interesting here is we do have a double pin set up or dual holes here. more
8/11/2015 11:56:31 AM
Trailer Hitch Installation - 2014 Subaru Forester - Draw-Tite- Video
Today, on our 2014 Subaru Forester, we're going to take at, and show you how to install, the Draw-Tite Max-Frame Customer Fit Trailer Hitch Receiver. This is a Class III, which is going to offer a 2 inch by 2 inch opening. Part number is 75876. Here's what our hitch is going to look like once we get it installed. Nice, clean look. Pretty narrow - it's going to drop down from our mounting location - no drilling required, so a pretty easy install. We've got a 2 inch by 2 inch receiver tube opening that's going to be our Class III. more
8/11/2015 11:56:06 AM
Trailer Hitch Installation - 2015 Subaru XV Crosstrek - Curt- Video
Today on our 2015 Subaru Xv cross track, we're going to take a look at and show you how to install the curtain custom fit class three trailer hitch receiver. This offers a two inch opening, its part number is C13135. Here's what the hitch looks like once we get it installed. As you can see it tucks nicely right underneath the rear bumper. Really beefs up the look of the back of the car. You've got tapered ends on each side which ads to the good looks of it. more
8/8/2015 4:07:35 PM
Trailer Hitch Installation - 2015 Subaru XV Crosstrek - Curt c11286- Video
Today on our 2015 Subaru XV Cross-track we're going to take at and show you how to install the Curt Custom Fit Class One Trailer Hitch Receiver. This offers a inch and a quarter opening. Part number is 11286. Here's what the hitch is going to look like installed on our Cross-track. Kind of tapers in at each end, pretty clean look across the back. It's going to give it a little bit of a beefier look. more
8/8/2015 4:07:16 PM
Trailer Hitch Installation - 2015 Subaru Legacy - Draw-Tite- Video
Today on our 2015 Subaru Legacy we're going to review and install the Draw-Tite class two 1-1/4" receiver tube hitch, part number 36493. Now here's what our hitch is going to look like once it's installed. This is a completely steel built hitch with a fully welded construction. We've got a nice strong square tube and the entire hitch has a black powder-coated finish to resist rust and corrosion. Here at the receiver tube we've got easy access chain hold downs on each side of the hitch and a 1/2" pinhole going all the way through. The hitch itself is capable of up to 300 pound tongue weight and a 3,500 pound tow capacity. Next we'll give you a couple measurements to assist you with selecting accessories for your new hitch. more
7/14/2015 11:59:19 AM
Trailer Hitch Installation - 2015 Subaru Legacy - Hidden Hitch- Video
Today on our 2015 Subaru Legacy we're going to review and install the Hidden Hitch class two 1-1/4" receiver tube hitch, part number 90208. Now here's what our hitch is going to look like once it's installed. This is a completely steel built hitch with a fully welded construction. We've got a nice strong square tube and the entire hitch has a black powder-coated finish to resist rust and corrosion. Here at the receiver tube we've got easy access chain hold downs on each side of the hitch and a 1/2" pinhole going all the way through. The hitch itself is capable of up to 300 pound tongue weight and a 3,500 pound tow capacity. Next we'll give you a couple measurements to assist you with selecting accessories for your new hitch. more
7/14/2015 11:57:05 AM
Trailer Hitch Installation - 2015 Subaru Legacy - Draw-Tite 75673- Video
Today in our 2015 Subaru Legacy, we're going to review and install the draw-tight max-spring class 3 two-inch receiver tube hitch part number 75673. Here's what it's going to look like once it's installed. Side brackets of our hitch tuck up nicely behind the rear fascia. The only thing really exposed is our square cross tube going into our receiver tube. On either side of the receiver tube is the large, easy-to-access chain hold downs. Going all the way through the receiver tube is going to be our five-eighths pinhole. Then a half inch hole designed to use with the J-pin style anti-rattle bowl. more
7/14/2015 11:56:06 AM
Trailer Hitch Installation - 2015 Subaru Outback Wagon - Hidden Hitch- Video
Today on our 2015 Subaru Outback wagon we're going to take a look at, then show you how to install the Hidden Hitch custom fit trailer hitch receiver. This is a class two hitch. It offers an 1-1/4" opening. Its part number is 90208. Now once we get our hitch installed, this is what we're going to see. It's going to be a nice, narrow, compact looking hitch. more
6/9/2015 2:32:29 PM
Trailer Hitch Installation - 2015 Subaru Outback Wagon - Draw-Tite- Video
Today on our 2015 Subaru Outback wagon we're going to take a look at, then show you how to install the Draw-Tite class two custom fit trailer hitch receiver. This offers an 1-1/4" opening. Its part number is 36493. Now once we get our hitch installed, this is what we're going to see. It's going to be a nice, narrow, compact looking hitch. The crosstube is not big and obnoxious. more
6/5/2015 1:57:40 PM
Trailer Hitch Installation - 2012 Subaru Forester - Curt- Video
Today on our 2012 Subaru Forester, we're going to review an install, the CURT class 3 two inch receiver tube hitch, part number 13147. Here's what our hitch is going to look like once it's installed. As you can see, we've got the nice, stylish, round cross tube design. It's a fully welded construction, with a really nice black powder coated finish to prevent rust and corrosion. On the other side of our receiver tube is our chain hold down, and then pre drilled all the way through the receiver tube is our 5/8ths pin hole. This is a class three 2 inch by 2 inch receiver tube, and is capable of up to 400 pounds of tongue weight with a 4,000 pound tow capacity. Next, I'll give you a couple measurements to assist you with selecting accessories for your new hitch. more
6/3/2015 12:02:43 PM
Trailer Hitch Installation - 2012 Subaru Forester - Curt C12047- Video
Today on our 2012 Subaru Forester, we're going to review and install the Curt Class 2 1-1/4 inch Receiver Tube Hitch, Part #C12047. Here's what it's going to look like once installed. As you can see, we've got the nice, stylish round cross tube design, the fully welded construction, and the nice black powder-coated finish. On each side of our receiver tube is our chain hold down, and pre-drilled is our 1/2 inch pinhole that goes all the way through the receiver tube. This is our Class 2 1-1/4 inch by 1-1/4 inch receiver tube and it's capable of up to 350 pounds of ton weight and 3,500 pound tow capacity. Next we'll give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 4-1/4 inches. more
6/1/2015 9:31:06 AM
Trailer Hitch Installation - 2015 Subaru Outback Wagon - Draw-Tite 75673- Video
Today on our 2015 Subaru Outback Wagon we're going to take a look at and show you how to install the Draw-Tite Max Frame Trailer Hitch Receiver. This is a custom fit class 3 receiver with a 2 inch opening, its part number is 75673. Here's what the hitch is going to look like once you get it installed. It's a nice class 3 hitch, it's going to give us a lot of options as far as what we can use it with, cargo carriers, bike racks, towing's not a problem with this. This is going to offer a 600 pound maximum tongue weight rating and a 4,000 pound gross trailer weight rating, of course check the owner's manual in the Outback, make sure it can handle that, if not go off of what ever of those numbers are the lowest. You can see this is going to have the dual pin set up. The one furthest in is for our hitch pin and clip, maybe our anti-rattle device, maybe our locking hitch pin, any 5/8 accessory will work great with that. more
5/29/2015 11:46:59 AM
Trailer Hitch Installation - 2008 Subaru Legacy - Draw-Tite- Video
Today on our 2008 Subaru Legacy we're going to take a look and show you how to install the Draw-Tite class three custom fit trailer hitch receiver. This is part number 75560. Here you can see the hitch once we get it put on the vehicle. It's a really nice, clean looking hitch. It's not one of the straight across; it's got that taper to it. It draws back just a small bar there that we can see. more
5/13/2015 11:16:57 AM
Trailer Hitch Installation - 2008 Subaru Legacy - Curt- Video
Today on our 2008 Subaru Legacy, we're going to take a look at, then show you how to install, the Curt Custom Fit Trailer Hitch Receiver. This is a Class 2, inch and a quarter. It's part number is C12284. Here's what the hitch is going to look like on the car. As you can see, real easy to get to, accessible right here in the middle. It's about flush with the end of the bumper, maybe inset just a touch. So, pretty even. more
5/7/2015 1:14:29 PM
Trailer Hitch Installation - 2008 Subaru Legacy - Hidden Hitch- Video
Today on our 2008 Subaru Legacy we're going to take a look at, then show you how to install the Hidden Hitch custom fit class two trailer hitch. This is going to offer an 1-1/4" opening. Its part number is 90138. Here's what the hitch is going to look like once installed. As you can see, it's kind of tapered back right here to our middle connection point or the receiver tube opening. A lot of your hardware is tucked up there where you really can't see it. more
5/7/2015 1:13:41 PM
Trailer Hitch Installation - 2008 Subaru Legacy - Draw-Tite 36334- Video
Today on our 2008 Subaru Legacy we're going to take a look at, then show you how to install the Draw-Tite custom fit class two trailer hitch receiver. This is an 1-1/4" opening style hitch. Part number is 36334. Here's what the hitch is going to look like once installed. As you can see, it's kind of tapered back right here to our middle connection point or the receiver tube opening. A lot of your hardware is tucked up there where you really can't see it. more
5/7/2015 1:13:02 PM
Trailer Hitch Installation - 2014 Subaru Outback Wagon - Curt- Video
Today on our 2014 Subaru Outback Wagon, we're going to take a look at and show you how to install the Curt Custom-Fit Class III 2" Trailer Hitch Receiver. This is part number C13206. Here's what the hitch looks like once we get it installed on our vehicle. As you can see, it's kind of a narrow line hitch, gives that nice, robust, heavy-duty appearance to it which goes right in line with the Outback's go anywhere outdoors kind of mentality, really beefens up the back here for us. It's a 2" by 2" receiver. We've got a collar all the way around. more
4/28/2015 12:57:11 PM
Trailer Hitch Installation - 2006 Subaru Impreza - Curt- Video
Today on our 2006 Subaru Impreza we're going to take a look at and show you how to install the CURT custom fit class one trailer hitch, part number C11318. Here you can see what the hitch looks like once it's installed on the vehicle. Now, as you can see, it comes down maybe just a little further than some of the others that I've seen here, but it was also a little easier to put in the car because of the way this is designed here. It's a little bit thinner area that goes over our exhaust system, so kind of some give and some take there. It hangs down here, which is a little different I think than what some of the other ones do. Aesthetically, you may decide you like one over the other. Something we did like about this this hitch is that it mounts using just four bolt hole locations rather than the six. more
4/13/2015 11:31:33 AM
Trailer Hitch Installation - 2006 Subaru Impreza - Hidden Hitch- Video
Today on our 2006 Subaru Impreza we're going to be installing the Hidden Hitch custom fit class one trailer hitch receiver. Part number 60823. Here's what the hitch is going to look like once you've got it installed on your Impreza. As you can see it comes across the rear pretty nicely. Just hangs down from that buffer slightly. No more than what the rear cover did on this one which is the STI. These are factory mounting locations on each side so you're not going to have to worry about pulling through any wires, any kind of fish wiring. more
4/9/2015 11:26:54 AM
Trailer Hitch Installation - 2006 Subaru Impreza - Draw-Tite- Video
Today on our 2006 Subaru Impreza we're going to take a look at and show you how to install the Draw-Tite custom fit sport frame trailer hitch receiver. This is a class one 1-1/4" hitch. Its part number is 24710. Here's what the hitch is going to look like once you've got it installed on your Impreza. As you can see, it comes across the rear pretty nicely. Just hangs down from that bumper slightly no more than what the rear cover did on this one, which was the STI. Uses factory mounting locations on each side so you're not going to have to worry about pulling through any wires, any kind of fish wiring, anything like that. more
4/9/2015 11:26:06 AM
Trailer Hitch Installation - 2015 Subaru Forester - Hidden Hitch- Video
Today in this 2015 Subaru Forester, we're going to show you part number 90228. This is the Hidden Hitch Class II 1-1/4-inch Receiver Hitch. Okay. This is what the hitch looks like when it's installed on our Forester. First off, overall look that does sit below the bumper here probably about 5 inches below the plugs here on our trunk pan. Take a look at the receiver, from a 1-1/4 inch across, has a nice reinforcement collar on the front. more
2/24/2015 1:56:08 PM
Trailer Hitch Installation - 2015 Subaru Forester - Draw-Tite 36523- Video
All right, today on this 2015 Subaru Forester, we're going to show you part number 36523 from Draw-Tite. This is a Class II, inch and a quarter receiver hitch. This is what the hitch looks like when it's installed on our Forester. For a soft overall look that does sit below the bumper here, probably about 5 inches below the plugs here on our trunk pan.Take a look at the receiver from the inch and a quarter across, has nice reinforcement collar. On the front, it also has a continuous loop here for your safety chains. A couple other details about our hitch. more
2/24/2015 1:55:50 PM
Trailer Hitch Installation - 2005 Subaru Baja - Hidden Hitch- Video
Today, on this 2005 Subaru Baja, we're going to install part number 60982 from Hidden Hitch. OK, this is what the hitch looks like once installed on the Baja. Next, we'll give you some measurements, that will help you out in selecting some accessories, such as the bicycle rack or a cargo carrier. From top of receiver opening down to the ground will be about 15 inches. From the center of the hitch pin hole, to the edge of the bumper will be about 4 inches. Now I'll go ahead and show you how the hitch is installed. First thing we do is get our vehicle ready. There are 2 wheel nuts and an impact bar we need to clean out first. more
12/11/2014 2:14:48 PM
Trailer Hitch Installation - 2005 Subaru Baja - Draw-Tite- Video
Today on our 2005 Subaru Baja we're going to install part number 24735 from Draw-Tite. This is what the hitch looks like when it's installed on the Baja. Next we'll give you some measurements that'll help you out in selecting some accessories, such as a bicycle rack or cargo carrier. From the top of the receiver opening down to the ground will be about fifteen inches. From the center of the hitch pinhole to the edge of the bumper will be about four inches. Now we'll go ahead and show you how the hitch is installed. more
12/11/2014 2:13:14 PM
Trailer Hitch Installation - 2008 Subaru Outback - Hidden Hitch- Video
Today on our 2008 Subaru Outback wagon we'll be installing our Hidden Hitch 1-1/4" receiver tube hitch, part number 90138. Here's what our hitch will look like once it's installed. Next we'll go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 6". From the top of the receiver tube opening to the ground is 13-1/2". This will assist you with selecting accessories such as a ball mount, bike rack, or cargo carrier. more
10/29/2014 3:24:05 PM
Trailer Hitch Installation - 2008 Subaru Outback - Draw-Tite- Video
Today on our 2008 Subaru Outback Wagon well be installing the Draw-Tite 1-1/4 Receiver Tube Hitch, part number 36334. Heres what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 6 inches. From the top of the receiver tube opening to the ground is 13-1/2 inches. This will assist your selecting accessories such as a ball mount, bike rack or cargo carrier. Well now go ahead with the installation. Before we lower the exhaust were going to put a safety strap underneath so that after we remove the rubber isolators that hold the exhaust in place we can use the safety strap to safely lower the weight of the exhaust. more
10/29/2014 3:14:37 PM
Trailer Hitch Installation - 2010 Subaru Forester - Curt- Video
Today on our 2010 Subaru Forester, we'll e installing the CURT Hitch, part number C12047. This is what our hitch will look like once installed. Next we'll go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4 inches. From the top of the receiver tube opening to the ground is 14-3/4 inches. This will assist you in selecting accessories such as a ball mount, bike rack or cargo carrier. Now we'll go ahead with the installation. Before we begin removing the rubber isolators from metal hangers, we'll go ahead and take a safety strap and put it under the exhaust so that it'll help control the weight and we can safely lower it. We'll first go ahead and locate the exhaust hangers. There are a total of five hangers, two for each muffler, one on the inside and outside of the muffler and then one just forward of the rear axle. more
10/20/2014 11:23:05 AM
Trailer Hitch Installation - 2010 Subaru Forester - Curt 13147- Video
Today on our 2010 Subaru Forester, we'll be installing the Curt 2 Inch Receiver Tube Hitch, part number 13147. Next we'll go ahead and give you some hitch measurements that will assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4-3/8". From the top of the receiver tube opening to the ground is 14-3/4". This will assist you with selecting accessories such as a ball mount bike rack, or cargo carrier. Now we'll go ahead with the installation. Before we begin, removing the rubber inaudible 00:00:33 from metal hangers, we'll go ahead and take a safety strap and put it under the exhaust so that it'll help control the weight and we can safely lower it. We'll first go ahead and locate the exhaust hangers. more
10/20/2014 11:21:12 AM
Trailer Hitch Installation - 2009 Subaru Forester - Hidden Hitch- Video
Today on our 2009 Subaru Forester we're going to be installing the Hidden Hitch trailer hitch receiver, part number 60893. Now here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch, such as a bicycle rack or a cargo carrier. From the top of the opening in the receiver to the ground we have 14". From the center of the hitch pinhole to the outermost edge of the bumper we have 6". Now let's go ahead and install our hitch. To begin with, let's go ahead and point out the five rubber exhaust hangers that we're going to need to remove in order to lower our exhaust down out of the way enough to install our hitch. Now before we remove any of these rubber exhaust hangers we're going to go ahead and install a safety strap to support the exhaust so it doesn't get lowered down or doesn't come down too far where it could be damaged. more
10/6/2014 3:37:17 PM
Trailer Hitch Installation - 2009 Subaru Forester - Draw-Tite- Video
Today on our 2009 Subaru Forester we're going to be installing the Draw-Tite trailer hitch receiver, part number 24807. Now here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch, such as a bicycle rack or a cargo carrier. From the top of the opening in the receiver to the ground we have 14". From the center of the hitch pinhole to the outermost edge of the bumper we have 6". Now let's go ahead and install our hitch. To begin with, let's go ahead and point out the five rubber exhaust hangers that we're going to need to remove in order to lower our exhaust down out of the way enough to install our hitch. more
10/6/2014 3:36:04 PM
Trailer Hitch Installation - 2013 Subaru Impreza - Curt- Video
Today on our 2013 Subaru Impreza Hatchback, were going to be installing the Curt Trailer Hitch receiver, part number C11286.Now, heres what our hitch looks like installed on our vehicle. Now, well go ahead and give you a couple of measurements in helping you choose some accessories for your hitch, such as a bicycle rack or a cargo carrier.From the top of the opening in the receiver to the ground, we have 10 inches. From the center of the hitch pin hole to the outermost edge of the bumper, we have 2 inches.Now, lets go ahead and install our hitch. Now, were going to begin over here on the driver side. Were going to need to remove two rubber plugs to open up our mounting locations. One is right here, and the other one is right here. more
10/5/2014 10:28:10 AM
Trailer Hitch Installation - 2008 Subaru Outback Wagon - Draw-Tite- Video
Today on our 2008 Subaru Outback Wagon we'll be installing the Draw-Tite Hitch, part number 75560. Here's what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is six inches. From the top of the receiver tube opening to the ground is thirteen and a half inches. This will assist you in selecting accessories such as a ball mount, bike rack, or cargo carrier. more
10/5/2014 10:02:34 AM
Trailer Hitch Installation - 2009 Subaru Forester - Hidden Hitch 90222- Video
Today on our 2009 Subaru Forester, we're going to be installing the Hidden Hitch Trailer Hitch Receiver, part number 90222. Here's what our hitch looks like installed on our vehicle. We'll go ahead and give you a couple of measurements in helping you choose some accessories for your hitch, such as ball mount, a bicycle rack or a cargo carrier. From the top of the opening in the receiver to the ground, we have 13 and 3/4 inches. From the center of the hitch pin hole to the outermost edge of our bumper, we have 6 inches. Let's go ahead and install our hitch. To begin with, let's point out the five rubber exhaust hangers that we're going to need to remove in order to lower our exhaust down out of the way enough to install our hitch. Before we remove any of these rubber exhaust hangers, we're going to go ahead and install a safety strap to support the exhaust so it doesn't get lowered down or doesn't come down too far, where it could be damaged. more
10/5/2014 8:24:11 AM
Trailer Hitch Installation - 2009 Subaru Forester - Draw-Tite 36521- Video
Today on our 2009 Subaru Forester, were going to be installing the Draw-Tite Hitch, part number 36521. Heres what our hitch looks like installed on our vehicle. Now, well go ahead and give you a couple of measurements in helping you choose some accessories for your hitch, such as a ball mount, a bicycle rack, or a cargo carrier. From the top if the opening in the receiver to the ground, we have 13 inches. From the center of the hitch pin hole to the outermost edge of our bumper, we have 6 inches. Now, lets go ahead and install our hitch. To begin with, lets go ahead and point out the five rubber exhaust hangers that were going to need to remove in order to lower our exhaust down out of the way and off to install our hitch. Now, before we remove any of these rubber exhaust hangers, were going to go ahead and install a safety strap to support the exhaust, so it doesnt get lower down or doesnt come down too far where it could be damaged. Were going to use a little bit of spray lubricant and large pry bar to remove the rubber exhaust hangers. Next, well go ahead and use our safety strap now that our rubber exhaust hangers have been removed to lower our exhaust down to give ourselves a little more working room. Next, were going to need to remove a bolt from each side of our heat shield. more
10/5/2014 8:23:59 AM
Trailer Hitch Installation - 2013 Subaru Outback Wagon - Hidden Hitch- Video
Today on our 2013 Subaru Outback Wagon were going to install Hidden Hitch 1-1/4 Inch Receiver Tube Hitch, part number 90208. Heres what our hitch will look like once its installed. Next Ill go ahead and give you a couple measurements that will assist you in selecting accessories such as a ball mount, bike rack or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4-3/4 inches. From the top of the receiver tube opening to the ground is 10-1/4 inches. Well now go ahead with the installation. Now to begin our install we need to lower the exhaust so we can gain access to the frame on both sides. For this application youll notice this only has a single exhaust. more
10/3/2014 5:11:52 PM
Trailer Hitch Installation - 2013 Subaru Outback Wagon - Draw-Tite- Video
Today on our 2013 Subaru Outback Wagon we'll be installing the Draw-Tite Hitch part number 75673. Here's what our hitch looks like once it's installed. Next I'll go ahead and give you a couple of measurements that will assist you with selecting accessories such as a ball mount, bike rack, or cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is 5 1/2 inches. From the top of the receiver tube opening to the ground is 14 1/4 inches. We'll now go ahead with the installation. Now to begin our install we need to lower the exhaust so we can gain access to the frame on both sides. For this application you'll notice it's only got a single exhaust. more
10/3/2014 5:07:40 PM
Trailer Hitch Installation - 2013 Subaru Outback Wagon - Draw-Tite 36493- Video
Today on our 2013 Subaru Outback Wagon well be installing the Draw-Tite Hitch, part number 36493. Heres what our hitch will look like once its installed. Next Ill go ahead and give you a couple measurements this will assist you with selecting accessories such as a ball mount, bike rack or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4-3/4 inches. From the top of the receiver tube opening to the ground is 10-1/4 inches. Well now go ahead with the installation. Now to begin our install we need to lower the exhaust so we can gain access to the frame on both sides. For this application youll notice this only has a single exhaust. more
10/3/2014 5:05:58 PM
Trailer Hitch Installation - 2013 Subaru Forester - Curt- Video
Today on our 2013 Subaru Forester, we'll be installing the Curt inch and a quarter receiver hitch, part number C12047. This is what our hitch will look like once installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4 inches. From the top of the receiver tube opening to the ground is 14 inches. This will assist you in selecting accessories such as a ball mount, bike rack or cargo carrier. more
9/22/2014 10:40:54 AM
Trailer Hitch Installation - 2013 Subaru Forester - Hidden Hitch- Video
Today on our 2013 Subaru Forester, we'll be installing Hidden Hitch Class III Receiver Hitch, part number 87493. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 6-3/4 inches. From the top of the receiver tube opening to the ground is 14 inches. This will assist you in selecting accessories such as a ball mount, bike rack, or cargo carrier. Now, we'll go ahead with installation. Now to begin our install, we'll first need to lower the exhaust. more
9/22/2014 10:39:14 AM
Trailer Hitch Installation - 2013 Subaru Forester - Draw-Tite- Video
Today on our 2013 Subaru Forester, we'll be installing the Draw-Tite Hitch, part number 75650. This would our hitch will look like once it's installed, next we'll go and give you a couple of measurements to assist your selecting accessories within your hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 6-3/4 inches. From the top of the receiver tube opening to the ground is 14 inches. This will assist your selecting accessories such as a bolt mount, bike rack or cargo carrier. Now we'll go ahead with the installation. more
9/22/2014 10:36:13 AM
Trailer Hitch Installation - 2013 Subaru Forester - Hidden Hitch 60893- Video
Today on our 2013 Subaru Forester we'll be installing the Hidden Hitch class one receiver hitch, part number 60893. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple measurements to assist your with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 6-1/2". From the top of the receiver tube opening to the ground is 14". This will assist you with selecting accessories such as a ball mount, bike rack, or cargo carrier. more
9/22/2014 10:33:38 AM
Trailer Hitch Installation - 2013 Subaru Forester - Draw-Tite 24807- Video
Today on our 2013 Subaru Forester we'll be installing the Draw-Tite hitch, part number 24807. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple measurements to assist your with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 6-1/2". From the top of the receiver tube opening to the ground is 14". This will assist you with selecting accessories such as a ball mount, bike rack, or cargo carrier. more
9/22/2014 10:31:42 AM
Trailer Hitch Installation - 2013 Subaru Forester- Video
Today on our 2013 Subaru Forester well be installing the Curt 2 Inch Hitch, part number 13147. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/4 inches. From the top of the receiver tube opening to the ground is 14-1/4 inches. This will assist your selecting accessories such as a ball mount, bike rack or cargo carrier. Now well go ahead with installation. Now to begin our install well first need to lower the exhaust. more
9/16/2014 5:15:35 AM
Filter Videos
Filter Videos
