Summer Starts Here - Save up to 70%
Trailer Hitch Installation - 2008 Chrysler Town and Country - Curt- Video
Today on our 2008 Chrysler Town & Country we're going to be taking a look at and installing the Curt Class II Custom Fit Trailer Hitch Receiver, part number C12264. Here's what our hitch looks like fully installed. It's going to sit up underneath our bumper and all we're going to see is the receiver tube opening. Now, it is a class II, so it's going to give you that inch and 1/4 by inch and 1/4 receiver tube opening, and it has a nice reinforced collar, giving it that nice clean, flush look. Now, our hitch is going to use a standard 1/2 inch pin and clip which is included, so that's a nice benefit of not having to pick anything extra up. Now, the safety chain loops are going to be a rolled steel stock that's welded onto the bottom and as you can see, we're going to have plenty of room to get most sized chains on or off without interfering with anything. Now, our hitch is going to feature a 3,500 pound gross trailer weight rating and a 350 pound tongue weight. more
4/19/2017 9:07:25 AM
Trailer Hitch Installation - 2017 Chrysler Pacifica- Video
Today on our 2017 Chrysler Pacifica, we're going to take a look at and also show you how to install the Draw-Tite max frame custom fit class 3 trailer hitch receiver. It offers the 2 inch by 2 inch receiver tube opening, it's part number is 76046. Here's what our hitch is going to look like installed. As you can see something I like about this hitch, our cross tube stays pretty hidden up behind the fascia. That's different than what we've seen from some of the other hitches. Whereas that's going to come over here to our receiver tube opening, this is 2 inch by 2 inches. Reinforcement collar around in there looks nice and neat. more
11/10/2016 1:37:28 PM
Trailer Hitch Installation - 2017 Chrylser Pacifica- Video
Today on our 2017 Chrysler Pacifica we're going to take a look at and show you how to install the Curt Custom Fit class two trailer hitch receiver. This offers the inch and a quarter by inch and a quarter opening. It's part number is C12159. Here's what our hitch is going to look like installed. We've got a pretty narrow cross tube comes around here, it's going to meet at the middle with our inch and a quarter by inch and a quarter receiver tube opening here. You can see Curt offers a flush reinforcement collar here around the end. It gives it a nice clean look. more
11/8/2016 10:45:30 AM
Trailer Hitch Installation - 2017 Chrysler Pacifica C13286- Video
Today on our 2017 Chrysler Pacifica, we're going to take a look at and also show you how to install the Curt Custom Fit Class Three Trailer Hitch Receiver, offering the 2 inch by 2 inch receiver tube opening. Its part number is C13286. Here's what our hitch looks like installed. We've got our round tube it comes across, and it's going to go to our side plates there, which are going to connect to the frame. Here in the middle we've got our 2 inch by 2 inch receiver tube opening. You can see, Curt's got a nice flush collar around the end of it there, which gives it a nice look. Side plates are going to come up, oval shaped holes in there. more
11/1/2016 1:36:29 PM
Trailer Hitch Installation - 2005 Chrysler Pacifica - Draw-Tite- Video
Today on our 2005 Chrysler Pacifica, we're going to review and install the Draw-Tite class three receiver hitch, part number 75522. This is what the hitch looks like once installed on Pacifica. Our hitch does have a two inch opening right here, which works with a wide variety of ball-mounts, and other accessories such as bike racks or cargo carriers. Also, you can see how it fits on the vehicle on the edge of the hitch here, it's just behind this edge of the bumper. You notice our hitch has two holes on each side. This 5/8 diameter hole right here is designed for your hitch-pins, or locking hitch-pins, for all of your accessories. This smaller diameter hole here that is on both sides, is designed for use of J-pin stabilization pin. That works with all of your accessories and ball-mounts that do not have their own anti-rattle devices built in. On the very bottom of our hitch, we have our safety-chain loops right here. more
9/30/2016 11:06:38 AM
Trailer Hitch Installation - 2006 Chrysler Town and Country - Draw-Tite- Video
Today on our 2006 Chrysler Town and Country, we'll be installing the Draw-Tite Max-Frame Class III Trailer Hitch Receiver, Part Number 75305. Here's what a hitch looks like once it's installed. As you can see, it tucks up fairly nicely behind the bumper of our vehicle. The only part that really hangs down is the two hitch receive itself, and a frame of the hitch. You see we've got this nice cutout around the exhaust, so we don't have to lower the exhaust all to install the hitch. The hitch installs using factory hardware already on the vehicle, so there's no drilling or modification of the vehicle required at all. more
7/21/2016 2:59:47 PM
Trailer Hitch Installation - 2014 Chrysler Town and Country - Draw-Tite- Video
Today on our 2014 Chrysler Town & Country we'll be installing the Draw-Tite Max-Frame 2" class three trailer hitch receiver, part number 75579. Here's what our hitch looks like once it's installed. As you can see, the only part that you can actually see is the 2" receiver itself, which is very nice because you don't have to look at the body of the hitch at all. It's all tucked up behind the bumper cover here. Here's our 2" hitch opening. As you can see right down below it, we have these easily accessible safety chain loops here to hook up the safety chains of our trailer. more
7/11/2016 12:36:49 PM
Trailer Hitch Installation - 2016 Chrysler Town and Country - Curt- Video
Today on our 2016 Chrysler Town , Country we're going to take a look at, then also show you how to install the CURT custom fit class two trailer hitch receiver. This offers the 1-1/4" by 1-1/4" opening. Its part number is C12264. Now here's a good look at what the hitch is going to look like installed. Our crosstube runs all the way across the rear here but it's really going to be hidden up behind this rear fascia. It gives you a nice look. more
6/23/2016 2:08:07 PM
Trailer Hitch Installation - 2006 Chrysler Town and Country - Curt- Video
Today on our 2006 Chrysler Town and Country, we'll be installing the curt trailer hitch receiver, inch and a quarter, class 2. Part number C12289. You can see it's a very clean installation here. You may note we have this nice little cut out here around the muffler. You don't have to worry about the hitch getting damaged from any exhaust gases or any heat that comes from the exhaust system. A nice gloss black, powder coat finish. This hitch is rated for 3,500 pounds gross trailer weight rating and 350 pounds of max tongue weight rating. You want to consult with your owner's manual of your 2006 Town and Country first and go by whichever numbers is less. more
6/23/2016 11:22:26 AM
Trailer Hitch Installation - 2013 Chrysler 300 - Curt- Video
Today on our 2013 Chrysler 300, we'll be installing the Curt Class III two inch receiver trailer hitch. Part number C13093. You can see a very minimal amount of the hitch hangs down. The two inch receiver is very easy to get to. It's not up underneath the bumper too far, so you can easily slide your draw bar, your bike rack or your cargo carrier in there. Our five eighths hitch pin hole here is easily accessible. You don't have to worry about it getting in the way of this plate here or where the safety chain loops are right here, to attach the safety chains on your trailer. more
6/14/2016 10:56:06 AM
Trailer Hitch Installation - 2013 Chrysler 300 - Curt C12064- Video
Today on our 2013 Chrysler 300, we will be installing the Curt Class II 1-1/4" Receiver Hitch, Part Number C12064. As you can see, a very minimal amount hangs down. The only part you really see is the 1-1/4" receiver right here and the two loops that are easily accessible for our safety chain hooks for our trailer to attach to. It has a nice gloss black powder-coated finish, so it'll be durable and provide us some corrosion residence from the salt and road grim and debris which may come in contact with it. This hitch has a 3,500-pound gross trailer weight reading and a 350-pound max tongue weight rating. You'll want to consult the owner's manual of your Chrysler 300 and go by the numbers that are listed in it. For a few measurements to better assist you in choosing any hitch-mounted accessories such as ball mounts, bike racks, or cargo carriers, you're looking at about 8 1/4" from the ground to the top of the 1 1/4" receiver, and you're looking at about 6" from the center of the 1/2" diameter hitch pin hole out to the far point of the bumper. If you're using this for a non-trailer application, such as using it for a bike rack or a cargo carrier, Curt requires that you use a cargo stabilization strap just to help support some of the load that is being placed on the hitch. more
6/10/2016 10:21:17 AM
Trailer Hitch Installation - 2013 Chrysler 300 - Draw-Tite- Video
Today on our 2013 Chrysler 300, we'll be installing the Draw-Tite Class 2 inch and a quarter trailer hitch receiver, part number 36548. Here's what our Draw-Tite hitch looks like installed. As you can see, it's a really clean installation. A very minimal amount is hanging down beneath the vehicle, just the inch and a quarter receiver right here sticking out a little bit underneath the bottom lip of the bumper, but it's still recessed behind the actual edge of the bumper, so it's not something you're going to be walking by and hitting your shin or your knee on. Plate here on the bottom of the hitch gives us a nice, secure mounting location for our safety chains, really easy to get to for you. This hitch has a half-inch diameter pin hole here, so you're going to use that for your hitch pin, your locking device, to secure your ball mount, bike carrier, or cargo rack. Just keep that in mind. This hitch has a 3500-pound max gross trailer weight rating, and a 300-pound max gross tongue weight rating. Now you want to consult the owner's manual of your Chrysler 300 and go by its number listed there. If the vehicle's only rated to tow 3000 pounds, obviously you don't want to go to the 3500 pounds that the hitch is rated for, or you could cause damage to the vehicle. Now for a few measurements to help you in choosing any hitch mounted accessories out there for you, such as ball mounts, bike racks, or cargo carriers, you're looking about six inches from the center of the hitch pin hole, out to the back of the bumper cover, and you're looking about ten inches from the ground to the top of the inch and a quarter Class 2 opening on the hitch. more
6/7/2016 2:16:23 PM
Trailer Hitch Installation - 2012 Chrysler 300 - Hidden Hitch- Video
Today on our 2012 Chrysler 300 we're going to be taking a look at, then showing you how to install, the Hidden Hitch Custom Fit Class II Trailer Hitch Receiver with the 1-1/4" by 1-1/4" opening. Part number is 90243. Here's what our hitch looks like installed, as you can see, if you get down low, you'll see that cross tube a little bit, but just kind of normal standing around, it's going to remain a little bit hidden for us, which is nice. The main part you'll see are going to be our safety chain connection plate here and our 1-1/4" receiver tube opening. See that does have the reinforced strap around the end to give us a little extra support there. The plates are also going to do a good job of stiffening that up for us. You can see the safety chain connection points are here. more
4/7/2016 3:46:22 PM
Trailer Hitch Installation - 2012 Chrysler 300 - Draw-Tite- Video
Today on our 2012 Chrysler 300, we're going to take a look at and show you how to install the Draw-Tite Custom Fit Class II Trailer Hitch receiver with the 1-1/4-inch by 1-1/4-inch opening. Part number is 36548. Here's what our hitch looks like installed. As you can see, if you get down low, you'll see that cross tube a little, but just normal standing around, it's going to remain a little bit hidden us for, which is nice. The main part you'll see is going to be our safety chain connection plate here and our 1-1/4-inch receiver tube opening. See that does have the reinforced strap around the end to give us a little extra support there. The plates are also going to do a good job of stiffening that up for us. You can see the safety chain connection points are here. more
4/7/2016 3:45:44 PM
Trailer Hitch Installation - 2015 Chrysler 200 - Draw-Tite- Video
Today on our 2015 Chrysler 200, we'll be taking a look at and installing the Draw-Tite Sportframe custom fit class 1 trailer hitch receiver, part number 24919. Here's what our hitch is going to look like once it's installed. It's going to have that nice sleek tucked up design where only the receiver tube and the chain tie downs are going to be visible. It's going to have that 1" by 1" receiver tube opening with your rolled steel for your chain tie downs on the other side. It's going to have a " pinhole going straight through. This is a class 1, it's capable of carrying up to 200lbs of tongue weight and 2,000lbs towing capacity. That's your trailer, fully loaded, with all your items. more
1/28/2016 3:31:51 PM
Trailer Hitch Installation - 2016 Chrysler Town and Country - Hidden Hitch- Video
Today on our 2016 Chrysler Town and Country we're going to take a look at and show you how to install the Hidden Hitch Custom Fit Class II Trailer Hitch Receiver. This is going offer the 1 1/4" x 1 1/4" opening. It's part number is 90169. Here's what our hitch is going to look like installed on the vehicle. You can see all we're going to see is our receiver tube opening and our safety chain connection points. That main cross tube has been hidden behind the bumper which is really nice. You get the use of a hitch without having a big thing all the way across the back of the vehicle. more
12/21/2015 8:36:55 AM
Trailer Hitch Installation - 2016 Chrysler Town and Country - Draw-Tite- Video
Today on our 2016 Chrysler Town and Country, we're going to take a look at and show you how to install the Draw Tite Max Frame Custom Fit Trailer Hitch Receiver. This is a class III, which is going to offer the 2 inch by 2 inch opening. It's part number is 75579. Here's what the hitch is going to look like installed. As you can see, not a lot going on back here, just the receiver tube opening and our safety chain connection points. The rest of it stays hidden up here behind our bumper where we don't have to see it. We're not going to have that cross tube going all the way across. more
12/21/2015 8:36:34 AM
Trailer Hitch Installation - 2016 Chrysler Town and Country - Hidden Hitch 87451- Video
Today on our 2016 Chrysler Town and Country we are going to take a look at and show you how to install the hidden hitch custom fit class 3 trailer hitch receiver. This offers the 2 inch by 2 inch opening. It's part number is 87451. Here's what the hitch is going to look like installed. As you can see not a lot going on back here, just the receiver tube opening and our safety chain connection points. The rest of it stays hidden up here behind our bumper we're we don't have to see it, we're not going to have that cross tube going all the way across. Again not adding to much to the back of the vehicle here, just a really useful addition. This is the class 3 hitch so we have the 2 inch by 2 inch receiver tube opening. more
12/16/2015 2:03:38 PM
Trailer Hitch Installation - 2016 Chrysler Town and Country - Draw-Tite 36455- Video
Today on our 2016 Chrysler Town and Country, we're going to take a look at and show you how to install the Draw-tite custom fit Class II trailer hitch receiver. This is going to offer an inch and a quarter, by inch and a quarter opening. It's part number is 36455. Here's what our hitch is going to look like installed on the vehicle. As you can see, all we're going to see is our receiver tube opening and our safety chain connection points. That main cross tube has been hidden in behind the bumper, which is really nice. You can get the use of the hitch without having a big thing all the way across the back of the vehicle. more
12/16/2015 2:03:18 PM
Trailer Hitch Installation - 2016 Chrysler Town and Country - Curt 13364- Video
Today on our 2016 Chrysler Town and Country, we're going to take a look at and show you how to install the CURT Custom Fit Class 3 Trailer Hitch Receiver. This s going to offer the 2 by 2 inch opening. It's part number is 13364. Now here's what our hitch is going to look like installed on the vehicle. As you can see, it's got a hidden crossbar. It's going to come across. That's what our receiver tube opening here is attached to. more
12/16/2015 2:02:54 PM
Trailer Hitch Installation - 2006 Chrysler Town and Country - Curt 13389- Video
Today on our 2006 Chrysler Town and Country, we're going to take a look at and show you how to install a CURT custom fit class 3 trailer hitch receiver. This offers a 2-inch opening. It's part number is 13389. Here's what our hitch look like once we get it installed on our Town and Country. As you can see, it's really custom-fit to fit right along the bottom edge of that bumper, receiver tubes nice and tucked in. It's inside of the rear bumper so we won't have to worry about hitting our knee on it as we walk by or anything like that. The exhaust comes out right here just above the hitch bracket, that kind of comes down and around. It's a nice heavy duty hitch, this is going to be great for your bike racks, cargo carriers, and even towing. more
8/8/2015 11:33:41 AM
Trailer Hitch Installation - 2012 Chrysler 300C - Curt- Video
Today on our 2012 Chrysler 300C, we are going to review and install the Curt Class 3, Two Inch Tube Receiver Hitch, Part Number C13093. Here is what our hitch is going to look like once installed. As you can see, it has got a nice low profile square tube design that goes into our fully welded construction in a really nice black powder coated finish so it blends with the under-body of the vehicle. On each side of our receiver tube is our chain hold down and it as got a pre-drilled hole that goes all the way through the receiver tube for our five ace pin or pin lock. This is a Class 3, two inch by two inch receiver tube that is capable of up to 350 pounds of tongue weight and a 3500 pound tow capacity. Next, we will go ahead and give you a couple measurements. This will assist you selecting accessories such as a ball mount, bike rack or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper, is six and one quarter inches. more
6/12/2015 3:06:43 PM
Trailer Hitch Installation - 2012 Chrysler 300C - Curt C12064- Video
Today on our 2012 Chrysler 300C we're going to review and install the CURT class two 1-1/4" receiver tube hitch, part number C12064. Here's what our hitch is going to look like once installed. As you can see, it's got a nice low-profile square tube design for our crosstube, into a fully welded hitch with a nice black powder-coated finish. We have a chain hold down on each side of our receiver tube, along with a pre-drilled 1/2" pinhole. Hitch itself is an 1-1/4" by 1-1/4" class two hitch that's capable of up to 350 pounds of tongue weight and a 3,500 pound tow capacity. Next we'll go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 6". more
6/10/2015 8:51:06 AM
Trailer Hitch Installation - 2012 Chrysler Town and Country - Curt- Video
Today on this 2012 Chrysler Town and Country, we're going to show you the CURT Class 2, 1-1/4 inch Receiver Hitch, part number C12264. This is what the hitch looks like when it's installed on a Town and Country. Now, you can see, there's not much there. At initial look at it, all you're really going to see is a receiver hitch and loops for safety chains. This is an 1-1/4 inch receiver that uses a 1/2 inch hitch pin or your favorite locking pin. We can take a look underneath the vehicle, we'll go ahead and see the structure of it. The body of the hitch is a square tube that goes out to both sides of the vehicle. Next, we'll go ahead and give you some measurements to help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. more
5/22/2015 10:36:50 AM
Trailer Hitch Installation - 2010 Chrysler 300 - Curt- Video
Today on our 2010 Chrysler 300, we're going to take a look at then show you how to install the Curt custom fit class three trailer hitch receiver. This offers a two inch opening. It's part number is one three four six five. Here's what the hitch is going to look like once you get it installed on your vehicle. As we can see, it's a nice, clean looking hitch. It's a class three, so we're going to have a lot of great uses for this whether we want to do our bike racks, some towing options this is going to offer all the way up to a three hundred fifty pound max tongue weight capacity, a thirty five hundred pound gross trailer weight capacity. more
5/14/2015 4:56:42 PM
Trailer Hitch Installation - 2015 Chrysler Town and Country - Curt- Video
Today on our 2015 Chrysler Town & Country we'll be installing the CURT class three hitch, part number 13364. Here's what our hitch will look like once it's installed. You'll note that it's got a nice square sturdy steel tube construction that will come with a limited lifetime warranty. Our hitch is made in the USA and is a class three hitch, which allows us to have up to 400 pounds of tongue weight and 4,000 pounds of towing weight, unless you add a weight distribution hitch and we'll have up to 500 pounds in tongue weight and 5,000 pounds of towing capability. The 2 by 2" receiver tube with a pre-drilled 5/8 pinhole. Additionally we have the chain hold down which is all you really get to see is the receiver tube and chain hold down, as everything else is nicely hidden behind the rear bumper. Next we'll go ahead and give you a couple measurements. more
2/4/2015 11:03:53 AM
Trailer Hitch Installation - 2015 Chrysler Town and Country - Curt c12264- Video
Today on our 2015 Chrysler Town & Country we'll be installing the CURT 1-1/4" receiver tube hitch, part number C12264. Here's what our hitch will look like once it's installed. We've got a square crosstube for a nice sturdy steel construction and it comes with a limited lifetime warranty. It's made in the USA and it's a class 2" hitch, which means it's capable of carrying 350 pounds of tongue weight with 3,500 pounds of towing weight. Here we have our 1-1/4" receiver tube, 1/2" pre-drilled hole, and our chain hold downs. Other than that, everything else is nicely concealed behind the rear bumper and doesn't stick out. Next I'll go ahead and give you a couple measurements. more
2/3/2015 5:18:04 PM
Trailer Hitch Installation - 2015 Chrysler Town and Country - Hidden Hitch- Video
Today on our 2015 Chrysler Town & Country we'll be install Hidden Hitch class three 2" receiver tube hitch, part number 87451. Here's what our hitch will look like once it's installed. We have a total of 400 pounds of tongue weight and 4,000 pounds of towing weight without a weight distribution hitch. With the weight distribution hitch it will add up to 500 pounds of tongue weight with 5,000 pounds of towing capability, and a pre-drilled hole for an anti-rattle bolt locking pin. One of the great features about this hitch is our crosstube and the main body of the hitch is hidden behind the bumper, and the only thing really showing is our receiver tube and chain hold down, but yet it's still very accessible. Next I'll go ahead and give you a couple measurements. This will assist you with selecting accessories such as a ball mount, bike rack, or cargo carrier. more
2/3/2015 5:04:03 PM
Trailer Hitch Installation - 2015 Chrysler Town and Country - Draw-Tite- Video
Today on our 2015 Chrysler Town & Country we'll be installing the Draw-Tite class three 2" receiver tube hitch, part number 75579. Here's what our hitch will look like once it's installed. We have a total of 400 pounds of tongue weight and 4,000 pounds of towing weight without a weight distribution hitch. With the weight distribution hitch it will add up to 500 pounds of tongue weight with 5,000 pounds of towing capability, and a pre-drilled hole for an anti-rattle bolt locking pin. One of the great features about this hitch is our crosstube and the main body of the hitch is hidden behind the bumper, and the only thing really showing is our receiver tube and chain hold down, but yet it's still very accessible. Next I'll go ahead and give you a couple measurements. This will assist you with selecting accessories such as a ball mount, bike rack, or cargo carrier. more
2/3/2015 5:00:23 PM
Trailer Hitch Installation - 2015 Chrysler Town and Country - Hidden Hitch 90169- Video
Today on our 2015 Chrysler Town & Country we're going to be installing the Hidden Hitch class two 1-1/4" receiver tube hitch, part number 90169. Here's what our hitch will look like once it's installed. We've got a nice powder-coated finish with a limited lifetime warranty. It's got a sturdy steel construction with a square crosstube design for additional strength. Our hitch has a 300 pound tongue weight capacity with a 3,500 pound towing capacity. Additionally, it's a really nice looking hitch because the crosstube is hidden behind the bumper and the only thing really revealed is our receiver tube and chain hold down. Next I'll go ahead and give you a couple measurements. more
2/2/2015 11:50:53 AM
Trailer Hitch Installation - 2015 Chrysler Town and Country - Draw-Tite 36455- Video
Today on our 2015 Chrysler Town & Country we'll be installing the Draw-Tite 1-1/4" receiver tube hitch, part number 36455. Here's what our hitch will look like once it's installed. We've got a nice powder-coated finish with a limited lifetime warranty. It's got a sturdy steel construction with a square crosstube design for additional strength. Our hitch has a 300 pound tongue weight capacity with a 3,500 pound towing capacity. Additionally, it's a really nice looking hitch because the crosstube is hidden behind the bumper and the only thing really revealed is our receiver tube and chain hold down. Next I'll go ahead and give you a couple measurements. more
2/2/2015 11:49:13 AM
Trailer Hitch Installation - 2015 Chrysler 300 - Curt- Video
Today on our 2015 Chrysler 300 we'll be installing the Curt 2" Receiver Tube Hitch, part number C13093. We've already got our hitch installed so we can see what it looks like. Here, we've got a nice rectangular or square tube cross tube that helps keep it nice and tight to the bottom of the vehicle while we still have access to our chain hold downs and our receiver tube. In the receiver tube it's already been pre-drilled for the 5/8ths standard pin and clip. This is a Class III hitch so it has a 350 lb tongue weight capacity and a 3500 lb tow capacity. I'll give you a couple measurements that will assist you with selecting accessories for your new hitch. more
1/30/2015 12:37:39 PM
Trailer Hitch Installation - 2008 Chrysler Aspen - Curt- Video
Today on this 2008 Chrysler Aspen, we're going to install part number 13072 from Curt. This is what the hitch looks like when it's installed on our Aspen. We'll give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be about twenty and three-quarter inches. The center of the hitch pin hole to the edge of the bumper will be about equal. Now we'll go ahead and show you how the hitch is installed. All right the first thing we need to is go ahead and lower our spare tire out of our way because we will have to do some drilling into the back of the bumper structure. more
1/15/2015 7:20:10 AM
Trailer Hitch Installation - 2008 Chrysler Sebring - Draw-Tite- Video
Today on our 2008 Chrysler Sebring we'll be installing Draw-Tite hitch, part number 24871. Here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a few measurements to help you select some accessories for your hitch such as a ball mount, bicycle rack, or cargo carrier. From the center of the hitch pinhole to the edge of the bumper is approximately 8". From the top of the opening of the receiver to the ground is approximately 11". Now let's go ahead and install our hitch. Now here's the hardware that we'll use for each side. more
1/8/2015 1:33:15 PM
Trailer Hitch Installation - 2012 Chrysler 200 - Draw-Tite- Video
Today on our 2012 Chrysler 200, we're going to be installing the Draw-Tite Trailer Hitch Receiver, part number 24871. Now here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch such as a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is approximately 7 1/4 inches. From the top of the opening in the receiver to the ground is approximately 11 inches. Now let's go ahead and install our hitch. Now we're first going to begin our installation by pointing out the rubber exhaust hangers that we need to remove so that we can temporarily lower down the exhaust to give our self a little more working room as well as allow the hitch to go up into position a little easier. more
12/12/2014 10:20:23 AM
Trailer Hitch Installation - 2001 Chrysler Town and Country - Draw-Tite- Video
Today on our 2001 Chrysler Town and Country, we'll be installing the Draw-Tite Hitch, part number 24702. Now to begin our install we'll move underneath the vehicle, and locate the bottom of the frame rail. Then moving forward from the end of the frame rail, we'll need to remove the manufacturer's bumper bolt. Inside the frame is the bumper structure and this bolt is one of the two that secure it. We're going to remove the forward bolt on each side first. Next, into the weld nut where we just removed the bolt, we're going to install a two-way threaded stud. Before I install it, I'm going to spray each weld-nut with a little spray lubricant to make it easier for our new stud to go in position. We're going to go ahead and thread it up into place as far as we can. Once we have the driver's side done, I'll move over to the passenger side and repeat the same process. more
11/26/2014 9:44:17 AM
Trailer Hitch Installation - 2007 Chrysler Town and Country - Draw-Tite- Video
Today on 2007 Chrysler Town & Country, we'll be installing the Draw-Tite hitch, part# 24702. This is what our hitch will look like once it's installed. Next, we're going to give you a couple measurements to assist you selecting accessories for your new hitch. Such as, a ball mount, bike rack or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/2 inches. From the top of the receiver tube opening to the ground is 12-3/4 inches. more
11/25/2014 3:03:01 AM
Trailer Hitch Installation - 2001 Chrysler Town and Country - Draw-Tite 36296- Video
Today on our 2001 Chrysler Town and Country well be installing the Draw-Tite Hitch, part number 36296. To begin our install well move underneath the vehicle and locate the bottom of the frame rail. Then moving forward from the end of the frame rail well need to remove the manufacturers bumper bolt. Inside the frame is the bumper structure and this bolt is one of the two that secure it. Were going to remove the forward bolt on each side first. Next into the weld nut where we just removed the bolt were going to install a two-way threaded stud. Before I install it Im going to spray each weld nut with a little spray lubricant to make it easier for our new stud to go into position. Were going to go ahead and thread it up into place as far as we can. more
11/24/2014 5:02:35 PM
Trailer Hitch Installation - 2008 Chrysler 300C - Curt- Video
Today on our 2008 Chrysler 300C we will be installing the CURT trailer hitch, part number 13465. Here's what it looks like installed. Now we'll give you a couple measurements to help you select accessories like bike rack's and cargo carriers. From the center of the hitch pinhole to the outermost edge of the bumper is about 7-1/2". From the top of the receiver tube to the ground is about 12-3/4". Now we'll show you how to install it. Now to start our installation one of the first things we'll want to do is support the exhaust before we lower it. more
11/13/2014 8:09:04 AM
Trailer Hitch Installation - 2003 Chrysler PT Cruiser - Curt- Video
Today, on our 2003 Chrysler PT Cruiser, we'll be installing a curt trailer hitch, part number C11132. Now, here's what the hitch looks like, when installed on the vehicle. Now, we'll go ahead and give you a few measurements, in helping you select some accessories for your hitch, such as a ball mount, bike rack, or cargo carrier. From the center of the pinhole to the edge of the bumper is approximately two and three quarter inches, and from the top of the opening of the hitch to the ground is approximately eleven and a quarter inches. Now, we'll go ahead and install our hitch. Before you actually remove the exhaust end, you may want to connect the safety strap under the exhaust, so it does not drop too much. You'll need to locate the two exhaust hangers, one that's near the muffler at the rear, and one that's a little farther forward on the vehicle. You may want to use a little spray lubricant to help these rubber isolators slide off their hook a little easier, as well as using a small pry bar or a large flat head screwdriver also helps. Now that we've got the exhaust out of the way, we'll need to remove eight bolts, four on each side, that are the tow hooks for the vehicle. more
11/12/2014 9:52:18 AM
Trailer Hitch Installation - 2007 Chrysler Town and Country - Draw-Tite 75119- Video
Today on our 2007 Chrysler Town & Country, we'll be installing the Draw-Tite hitch, part number 75119. This is what our hitch will look like once it's installed. Next, we're going to give you a couple measurements to assist your selecting accessories for your new hitch, such as a ball mount, bike rack, or cargo carrier. From the center of the hitchpin hole to the outermost edge of the bumper is 5 inches. From the top of the receiver tube opening to the ground is 12 and 1/4 inches. Now, we'll go ahead with installation. To begin our install, we'll first point out the attachment points. We'll have a total of 3 attachment points on each side. more
10/30/2014 12:24:46 PM
Trailer Hitch Installation - 2009 Chrysler 300 - Curt- Video
Today, on our 2009 Chrysler 300, we'll be installing the Curt Hitch, part number C12240. Here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch, such as a ball mount, bicycle rack, or cargo carrier. From the center of the hitch pinhole to the outermost edge of the bumper is approximately 6-3/4 inches. From the top of the opening in the receiver to the ground is approximately 10 inches. Now let's go ahead and install our hitch. To begin with, we'll need to go ahead and lower our exhaust out of the way. more
10/27/2014 2:42:49 PM
Trailer Hitch Installation - 2013 Chrysler Town and Country - Curt- Video
Today on our 2013 Chrysler Town & Country we'll be installing the Curt Hitch part number C12264. This is the Curt Class II 1-1/4 inch receiver tube hitch. First we'll need to gain access to the frame and to do that we'll lower the exhaust here on the passenger side. To lower the exhaust on this application we're going to remove the hardware from the hanger that secures it to the frame or body of the vehicle. We'll have one here at the tailpipe, one just in front of the rear axle which should give you enough clearance to get the hitch in. Quick tech tip, if we remove one more hanger, here at the front of the muffler, it'll give you some additional working room between the tailpipe and the frame. more
10/2/2014 1:10:30 PM
Trailer Hitch Installation - 2014 Chrysler Town and Country - Hidden Hitch- Video
Today on our 2014 Chrysler Town & Country, we'll install a hidden hitch 1/4 inch receiver tube hitch, part number 90169. Here's what our hitch will look like once it's installed. Next, we'll then give you a couple a measurements so you can select such accessories such as a ball mount, bike rack, or cargo carrier. From the center of the hitch pin hole, the outermost edge of the bumper is 6 and 3/4 inches. On top of the receiver tube opening to the ground is 11 inches. We'll now go ahead with the installation. We'll first need to lower the exhaust on the passenger side. more
10/1/2014 3:59:01 PM
Trailer Hitch Installation - 2014 Chrysler Town and Country - Draw-Tite 36455- Video
Today on our 2014 Chrysler Town and Country we'll be installing a Draw-Tite hitch, part number 36455. Here's what our hitch will look like once installed. Next we'll then give you a couple of measurements. This will assist you selecting accessories such as a ball mount, bike rack or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 6 and 3/4 inches. From the top of the receiver tube opening to the ground is 11 inches. more
10/1/2014 3:58:10 PM
Trailer Hitch Installation - 2010 Chrysler Town and Country - Hidden Hitch- Video
Today on our 2010 Chrysler Town and Country we'll be installing the Hidden Hitch, part number 90169. Here's what the hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch, such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pinhole to the outermost of the bumper is approximately 6". From the top of the opening in the receiver to the ground is approximately 13". Now let's go ahead and install our hitch. To begin with we'll need to go ahead and lower our exhaust out of the way. more
9/29/2014 9:38:25 AM
Trailer Hitch Installation - 2010 Chrysler Town and Country - Curt- Video
Today on our 2010 Chrysler Town and Country we'll be installing the CURT hitch, part number 133634. Here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories for hitch, such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is approximately 4". From the top of the opening in the receiver to the ground is approximately 13". Now let's go ahead and install our hitch. To begin with we're going to need to lower the exhaust down out of the way to gain access to the existing hardware that's in the frame on the passenger side. Before we lower the exhaust, though, we're going to go ahead and put a safety strap in place just in case so we can give the exhaust a little extra support once it's lowered down. more
9/29/2014 9:37:00 AM
Trailer Hitch Installation - 2014 Chrysler Town and Country- Video
Today on our 2014 Chrysler Town and Country, we'll be installing the Curt 1-1/4 inch Receiver Tube Hitch, part number C-12264. To begin our install, we'll first need to lower the exhaust on the passenger's side. There are two fasteners we'll want to remove with two separate hangers. One just behind the rear axle that holds the tail pipe, one just forward of the rear axle securing the muffler. Once we remove the two bolts, we'll allow the exhaust to come down. We can now gain access to the fasteners to the frame on the passengers side. So there are two fasteners that we'll need to access, starting at the rear of the frame will be the first two. more
9/18/2014 12:06:43 PM
Trailer Hitch Installation - 2008 Chrysler Town and Country - Curt 13364- Video
Today on our 2008 Chrysler Town and Country, we'll be installing the Curt 2 Inch Receiver Hitch, part number 13364. This is what our hitch will look like once installed. Next, we'll go ahead and give you a couple measurements to assist your selecting accessories for your new hitch, such as a ball mount, bike rack, or cargo carrier. From the center of the hitch pin hole, to the outermost edge of the bumper is 4 1/4 inches. From the top of the receiver tube opening to the ground is 13 inches. Now we'll go ahead with installation. Now to begin our install, we'll first go ahead and point out the attachment points. more
9/17/2014 9:47:21 AM
Trailer Hitch Installation - 2008 Chrysler Town and Country - Hidden Hitch- Video
Today on our 2008 Chrysler Town and Country, we'll be installing Hidden Hitch, part number 90169. This is what our hitch will look like once it's installed. Next we're going to give you a couple of measurements to assist your selecting accessories for your new hitch such as a ball mount, bike rack or cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is 7 inches. From the top of the receiver tube opening to the ground is 13 inches. Now we'll go ahead with the installation. Now to begin our install, we'll first go ahead and identify our attachment points. We'll have a total of four attachment points, two on each side. more
9/11/2014 3:19:29 PM
Filter Videos
Filter Videos
