Hopkins Custom Tail Light Wiring Kit Installation - 2011 Jeep Grand Cherokee- Video
Today, this 2011 Jeep Grand Cherokee, we're going to review and install the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles, Part number HM56207.This will provide all the signals you need. Turn signals, left and right, your running light circuit and your brake lights.You can use a bulb and socket in some vehicles, however, when you use a wiring system like this, you don't have to worry about drilling a hole in the back of your tail light and worrying about sealing up and getting moisture inside tail light when you're done installing it.Before we get ready to install, we'll cover the parts and which direction all the wires go. Pretty easy. The T-connector to yellow wire goes to the driver's side and the T-connection with the green wire goes over to your passenger side. Of course, the 4-pole wiring harness is going to go up towards the front of the vehicle.The kit also comes with a holder for a 4-pole flat, if you're going to stay with that, some zip ties to hold the wires, some screws for the bracket and some dielectric grease to protect your electrical connections and also a cap for a 4-pole.To start off our install, we remove both our tail lights. This is our driver's side here. more
1/7/2019 11:22:51 AM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2018 Jeep Grand Cherokee- Video
Today on our 2018 Jeep Grand Cherokee we're going to be installing Roadmaster's diode wiring kit, part number RM-15267. Our diode wiring kit runs from the rear tail lamp assemblies up to our six pole connector here. And here you can see in our motor home we have our left turn signal on, and here you can see when we activate the lights in our motor home it also matches on our Jeep.We've got everything else that we'll need to get our flat tow for our vehicle behind our motor home set up. We've got our tow bars, which is the connection point between your baseplate and your motor home's hitch, we have our breaking system, we have our wiring, which gives us all of our stop, turn, and tail lamp signals from our motor home to our vehicle. And to be able to connect our tow bar to our base plate we're using Roadmaster's quick disconnect kit.Your baseplate is going to be your interface that allows a connection to your motor home. This is where your tow bars will attach. more
12/12/2018 3:42:12 PM
Demco Tail Light Wiring Kit Installation - 2018 Jeep JL Wrangler Unlimited- Video
Speaker 1: Today on our 2018 Jeep Wrangler JL Unlimited, we're going to be taking a look at, and showing you how to install the Demco tail light wiring kit, part number DM9523010. Whenever we're flat-towing our Jeep down the road, it's very important that our light signals match up from the motorhome and the Jeep. That way if we're slowing down or changing lanes, everybody around us knows what's going on, and we can all be safe.Our diode kit is going to take that signal from our motorhome, and transfer it to our jeep, so that they blink and turn on at the same time. The really nice thing about our diodes is that it's not going to change the outward appearance of our Jeep at all, and the fact that once we have it installed, they're not going to have any maintenance. Unlike some of the magnetic lights that we'd have to hook up, run our wire every time we want to tow, we can simply have these already in and we just have the connection cord between our motorhome and Jeep to hook up.Our diodes are also going to make sure that it protects our vehicles wiring. We don't have to worry about any short-circuits or anything that may arise on the motorhome end, because our diodes are only going to let power go through one way. more
12/6/2018 2:33:40 PM
Hopkins Custom Tail Light Wiring Kit Installation - 2013 Jeep Grand Cherokee- Video
Speaker 1: Today on our 2013 Jeep Grand Cherokee, we're going to be taking a look at and showing you how to install the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles, part number HM56207.Whenever we're flat towing our Jeep behind our motor home, it's going to be important that all of our lights match each other. That way if we change lanes or if we slow down, we can safely make sure that everyone around us knows what's going on. Well our wiring kit is going to do that exactly. It's going to take the signal from our motor home and transfer them directly into our Jeep's taillights. That way we're not going to have to worry about making sure that they match up.Our wiring kit's going to give us all of our basic light functions, like our taillights, our turn signals, and our brake lights. It's going to prevent us from having to hook up those magnetic lights, set everything up every time that we tow our Jeep, as well as take them down when we want to drive. more
12/5/2018 11:32:40 AM
Roadmaster Tow Bar Wiring Kit Installation - 2016 Jeep Wrangler- Video
Speaker 1: Today on our 2016 Jeep Wrangler, we're gonna be taking a look at, I'm gonna show you how to install the Roadmaster Universal High Powered Diode Wiring Kit, part number RM-154.This is what our diode kit's gonna look like when it's installed. It's gonna be one of five main components on a flat tow setup, this is gonna give us our proper lighting functions at the back of our vehicle to safely flat two the vehicle.This is what our diode kit looks like when we get it. We're gonna have our diodes, we're gonna have our 30 foot of wire that's gonna go from the front of our Jeep to the back, we're gonna have our tether that's gonna go from the front of our Jeep to the back of our RV, we're gonna have some zip ties to help hold up our wiring when we run it to the back of the vehicle, and we're gonna have some wire loom to give our wiring a nice finished look.Our diodes, what these are for is these are gonna help protect our factory wiring from any back feed from our RV, if there's a wiring issue and vice versa. You're also gonna have some butt connectors. Now for this particular kit, you can see we had two 4 pole ends. The reason it has that, this is gonna be a kit for your older RVs and what you would do is you would take 3 foot on one side, cut it off, and you'd attach it to the other ... more
12/3/2018 11:12:20 AM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2012 Jeep Wrangler Unlimited- Video
Speaker 1: Today on our 2012 Jeep Wrangler Unlimited, you're going to be taking a look at . I'm going to show you how to install the Roadmaster diode seven-wire to six-wire Flexo-Coil wiring kit. Part number RM-15267. The five main components for a flat tow setup are your braking system, your wiring, your tow bar, your safety cables, and your base plate.This is what our diode kit's going to look like when you get it. What this is going to do for you is this is going to allow you to transfer the turn signals, brake lights, running lights from the RV through the Jeep to the Jeep's tail lights or to the Jeep's lights. Period. more
11/27/2018 11:12:13 AM
Tow Ready Tail Light Isolating Diode System Installation - 2019 Jeep Cherokee- Video
Speaker 1: Today, on this 2019 Jeep Cherokee, we'll be having a look at and showing you how to install the Tow Ready Tail Light Isolating Diode System with a Four-Pole Connector, part number TR118821.Now, in conjunction with our diode wiring harness, we also use a Roadmaster 7 to 6 Coil Kit. That'll give us the six-way connector that we have on the front of our vehicle, and give us a seven to six-way coil cord. We'll have the six-way end going into the front of the Cherokee, and the seven-way on our motor home.This is great because not only can you run your turn signals, your brake lights and your tail lights, but you can also run a charge line kit to charge your vehicle's battery. If you have a braking system with an indicator light on it, inside the motor home, you can run the indicator light wire through the six-way connector, through one of the unused terminals, and run that as well. You can have all those functions at the same time.Now, our six-way connector is great because we have this nice spring-loaded door on it which not only will protect it from the elements when it's not in use, but it'll also help hold our wiring plug in place when we are flat towing our Cherokee. We can easily remove the coiled end just by using the two finger hooks here and pulling out. more
11/13/2018 3:22:15 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2019 Jeep Cherokee- Video
Speaker 1: Today on in 2019 Jeep Cherokee, you're going to be taking a look at . I'm going to show you how to install the Roadmaster diode seven wire to six wire flex coil wiring kit, part number RM-15267.This is what our diode kit's gonna look like when it's installed. It's going to be one of five main components and a flat tow setup. The other four, you're going to be your base plate, safety cables, tow bar and your braking system.What the diode kit is going to do for you, it's going to allow you to transfer your light signals from your rv through your Jeep Cherokee so you can safely flat tow it. This diode's going to have an aluminum casing on it that's going to protect it from rust and corrosion. And it's going to tie into your factory tail light wiring.As far as our plug goes here in the front, it's going to be a six pole plug. more
11/9/2018 12:32:13 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2013 Jeep Wrangler- Video
Speaker 1: Today on our 2013 Jeep Wrangler, we're gonna be taking a look at and I'm gonna show you how to install the Roadmaster Diode 7- to 6-Wire Flexo-Coil Wiring Kit, part number RM-15267.The five main components for a flat tow setup are your braking system, your wiring, your tow bar, your safety cables, and your base plate.This is what our diode kit looks like when it's fully installed. This is gonna give you all the proper lighting functions to safely flat tow your vehicle.One thing to keep in mind. If you're installing a braking system, you will need a brake-lite relay for this vehicle. You can find it on our website using part number RM-88400.Here we have your flexo-coil. It's gonna give you your 7-pole side, it's gonna hook into your RV. Your 6-pole side, it's gonna hook into your towed vehicle, or your Jeep Wrangler. more
10/23/2018 1:17:12 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2018 Jeep JL Wrangler Unlimited- Video
Speaker 1: Today on our 2018 Jeep JL Wrangler Unlimited, you're going to be taking a look at and I'm going to show you how to install the Roadmaster diode seven to six wire flexicoil wiring kit, part number RM-15267.This is what our diode kit looks like when it's installed. It's going to be one of five main components on a flat tow set up. The other four are going to be your base plate, your tow bar, your safety cables, and your braking system. What the diode kit is going to allow you to do, it's going to allow you to utilize the lights on your Jeep while it's being flat towed. How it does that is you're going to get a flexicoil in your kit or umbilical cord that connects your plug here to the plug on the back of your RV.When you turn on the blinker in your RV, that signal is sent through this wire to the taillights on your Jeep. Now what the diodes are actually going to do for you, it's actually going to protect your vehicle from any feedback. more
10/4/2018 11:57:12 AM
Hopkins Tail Light Wiring Kit Installation - 2015 Jeep Wrangler- Video
Speaker 1: Today on our 2015 Jeep Wrangler, we're gonna be installing Hopkins Custom Tail Light Wiring Kit, part number HM56200. This wiring kit is gonna allow you to hook your vehicle up to your RV and get all the necessary lighting signals transfer from it to your vehicle. This includes your left turn, right turn, tail lamps, and brake lamps, so you'll be DOT compliant in all states.There's no cutting, no splicing required with this wiring kit, it just plugs in line with your factory wiring. The control box included will separate its circuits from your factory circuits, so you don't have to worry about any of the signals coming from your RV effecting the wiring on your vehicle. Everything you need to hook up to your RV is included, and it's custom fit for your Jeep. Now that we've gone over some of its features, let's show you how to get it installed.We'll begin our installation at the back of the vehicle by removing both the driver's and passenger's side tail light assemblies. more
9/10/2018 10:22:12 AM
Roadmaster Diode Flexo-Coil Wiring Kit Installation - 2005 Jeep Grand Cherokee- Video
Speaker 1: Today on our 2005 Jeep Grand Cherokee, we're going to be taking a look at showing you how to install the Roadmaster diode 7 wire to 4 wire flexi-coil wiring kit, part number RM-15247. This is what a diode kit looks like when it's installed. Its going to be one of five components in a flat tow setup. You're going to need a tow bar, a base plate, a braking system and safety cables. What this style is going to do, it's going to allow you to activate the lighting functions on your Jeep from your RV while it's being flat towed. The diodes are going to prevent feedback from both vehicles when hooked together, in turn protecting the wiring in both. more
8/22/2018 1:32:11 PM
Hopkins Custom Tail Light Wiring Kit Installation - 2004 Jeep Wrangler- Video
Speaker 1: Today on our 2004 Jeep Wrangler Sport we're gonna be taking a look at and showing you how to install the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles. Part Number HM56202. This is what our wiring looks like when it's installed. This is gonna provide us with all the proper functions when we're towing our vehicle, brake light, running lights, both turn signals, and our grounds. Now what's gonna set this apart from some of the other kits out there is the diodes are already integrated into a box, so you're not gonna have to cut any wires, or make any attachments. It's gonna plug directly into your tail lights, as opposed to some of the other ones where it's gonna comes with the diodes, but you have to splice into the existing wires running to your tail lights.In your kit you are gonna get a dust cover. more
8/10/2018 1:27:12 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2015 Jeep Grand Cherokee- Video
Speaker 1: Today on our 2015 Jeep Grand Cherokee, we're going to be taking a look and showing you how to install the Roadmaster Diode 7 Wire to 6 Wire Flexi Coil Wiring Kit, part number RN-15267. This is going to provide you with all the necessary lighting functions for your Jeep whilst it's being towed, your brake lights, your running lights, both turn signals, and your ground.It's also going to offer an extra hookup if you decide to put a battery charge line kit in which can be found on our website. It's going to be one of five main components and a flat tow setup, this being your lighting. You also need a tow bar, safety cables, your base plate, and your braking system. It's going to have a spring loaded cap. It's going to seal to help keep any moisture from getting to the connections inside when it's not being used.Your 6-pole plug is going to mount on the front of the vehicle, with the included bracket. more
8/6/2018 1:27:13 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2009 Jeep Liberty- Video
Speaker 1: Today on our 2009 Jeep Liberty, we're gonna be taking a look at and showing you how to install the Roadmaster Diode 7 Wire to 6 Wire Flexco Coil Wiring Kit, part number: RM-15267. A diode kit is gonna eliminate the need for those magnetic lights that you see a lot, that you stick on the side of your car, and you have to run the wires along the side. Because they're actually gonna get wired into our existing taillights with just a few components.It's gonna accept our RV stock tail and turn signals, and we're gonna be able to use them on our Liberty's factory taillight. We're not gonna have to drill a new hole in our taillights and put a new bulb in or use those magnetic lights.It's gonna come with a six way round socket, as well as the bracket to mount it on the front of your vehicle. You're gonna get a coiled cord that's gonna come with it, so we can hook our RV and our car up. Now, one of the big benefits of our diode wiring kit is that it is gonna prevent any kind of electrical feedback if there we're anything to arise in the motor home side and protect our vehicle's wiring.Now, since a vehicle has a separate turn signal opposed to the brake, our diode kit is actually gonna turn a brake signal into our turn signal while we're towing our Liberty. more
6/29/2018 1:27:12 PM
Roadmaster 4-Diode Universal Wiring Kit Installation - 2018 Jeep JK Wrangler Unlimited- Video
Speaker 1: Today on our 2018 Jeep Wrangler JK Unlimited, we're going to be taking a look at, and showing you how to install, the Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles with a 7-Wire to 6-Wire Straight Cord; and that's going to part number RM-152-98146-7.Whenever we're flat towing our Jeep, we're going to need lights from our motor home to let everyone else around us know what's going on, whether we're slowing down and then hitting the brakes or getting ready to make a turn. We need those signals to work back on the back of our Jeep.That's where our diodes are going to come into play. They're going to allow the signal to come from our motor home, go through, and use our factory taillights as the turn signal. So we're not going to have to worry about those magnetic lights. We're going to kind of be running wires on the outside of our Jeep every time we go to flat tow it. It's going to be a one time installation, and we're going to have all of our signals working with our factory lights.Not only are the diodes going to allow us to use those signals, but it's also going to protect our vehicles electrical system. more
5/31/2018 4:07:10 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2018 Jeep Cherokee- Video
Speaker 1: Today on our 2018 Jeep Cherokee, we're gonna take a look at and show you how to install the Roadmaster 7-wire to 6-wire Flexo-Coil Diode Wiring Kit for towed vehicles. Part number is RM-15267.Now this wiring kit's gonna be the perfect solution for towing your vehicle behind your motor home, and having the appropriate signals on the back. We've got our Flexo-Coil here, passes those signals through so whether we're hitting the brakes in our Coach, we have on our running lights or our turn signals, that's gonna show up on the back of the vehicle. The Flexo-Coil design will expand and contract as you can see, so we won't have to worry about it hanging down on the ground, but as we make our initial pull away from our vehicle when it's connected, it's gonna extend to the exact length that we need.Now the benefit of a wiring system that has diodes included will be that those are gonna isolate our RV from our vehicle so we won't have any type of back feeding. We can take a closer look at them now.So now what we've been able to do using our diode is take the signal from our RV, it comes in here, and the factory signal from our vehicle. That is then going to be converted to a single output, so whether the signal comes from the RV, it's allowed to pass directly through and go out and light our bulb. more
5/8/2018 4:32:11 PM
Roadmaster Universal Diode Wiring Kit Installation - 2018 Jeep Cherokee- Video
Speaker 1: Today on our 2018 Jeep Cherokee we're going to be installing Roadmaster's universal diode kit. Part number RM-152. Along with this we'll be using Roadmaster's seven wire to six wire straight cord, part number RM-98146-7.This diode kit is going to allow your RV to send its brake, turn, and tail lamp signals to the lights on your vehicle. This will allow vehicle behind you to know what you're about to do, and it will keep you in compliance with local laws.Here we are in our RV, and all of our signaling devices are going to activate back on our vehicle. It activates our left turn on both the RV and on our vehicle. The same happens with our right turn, our brake lamps, and our tail lamps.Along with this diode kit, it's going to come with a six pole connector, and a cable that goes from six pole to seven pole so you can hook it to your RV. more
4/26/2018 2:17:13 PM
Roadmaster 4-Diode Universal Wiring Kit Installation - 2018 Jeep Cherokee- Video
Speaker 1: Today on our 2018 Jeep Cherokee, we're going to be installing Roadmaster's Four Diode Universal Wiring Kit for Towed Vehicles. Part number RM-152-98146-7. This diode kit is going to allow your RV to send its brake, turn, and tail lamp signals to the lights on your vehicle.This will allow vehicles behind you to know what you're about to do, and will keep you in compliance with local laws.Here we are in our RV, and all of our signaling devices are going to activate back on our vehicle. It activates our left turn on both the RV and on our vehicle. The same happens with our right turn, our break lamps, and our tail lamps.Along with this diode kit, it's gonna come with a six pole connector and a cable that goes from six pole to seven pole so you can hook it to your RV. This is great not only for the diode kit and getting your signaling devices, but it acts as an interface that will connect your RV to your vehicle or other systems, such as a breaking system or any other signaling you may want to provide your vehicle.This diode and wiring kit connects to the tail lamp circuits here at the back of your vehicle. more
4/24/2018 1:12:10 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2014 Jeep Grand Cherokee- Video
Speaker 1: Today on this 2014 Jeep Grand Cherokee we'll be having a look at and showing you how to install the Roadmaster diode seven wire to six wire Flexo-Coil wiring kit, part number RM-15267.Here's what our diodes look like installed. As you can see what's great about this is that it utilizes the factory lights on our vehicle, so we don't have to deal with using a magnetic tow light when we want to flat tow our Grand Cherokee behind our motor home.Now, what sets this apart from other options out there is that by utilizing diodes, not only do we get to utilize our factory lights in the vehicle, but it also protects our expensive electrical components from any back feed of voltage from our motor home, so we don't have to worry about any damage happening to those components.What many of our customers like about this is it's one less thing they have to worry about. They don't have to worry about storing a pair of magnetic tow lights or the paint on their vehicle getting scratched from the light slipping and sliding on the surface. With this, you simply plug in one connection to your motor home and that's it. You don't have to worry about flipping any switches either because as soon as you unplug it and you want to drive your vehicle as normal, the factory lights work without any user intervention.Here's what it looks like on the front of our vehicle. The included six pull round connector will mount easily to your base plate. more
4/19/2018 12:25:05 PM
Roadmaster Universal Diode Wiring Kit Installation - 2016 Jeep Grand Cherokee- Video
Speaker 1: Today on our 2016 Jeep Grand Cherokee we'll be having a look at and showing you how to install the Roadmaster Universal high power diode wiring kit, part number RM-152. Here's what our diodes look like installed. Now the reason you're gonna want a set of diodes for your Grand Cherokee when you're flat towing it is that this will keep you safe and legal, giving you the necessary lighting functions required by law and you no longer have to worry about using magnetic tow lights on your vehicle which could scratch your paint.These diodes will allow you to use your factory taillight and brake light bulbs to treat your vehicle as a trailer now. Your brake light bulb will now function as your turn signals when you're flat towing and your factory taillight will still be you taillights when you're flat towing as well. This makes it quick and easy with no additional bulbs, it's utilizes what your vehicle already has in it from the factory. The diodes will serve as a protection method for your vehicle's expensive electrical components, not allowing any voltage to be back fed into your Jeep from your motor home.Our customers really like this because they think it works very well. more
4/12/2018 6:22:10 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2014 Jeep Wrangler- Video
Speaker 1: Today on our 2016 Jeep Wrangler, we're going to take a look at and also show you how to install the Roadmaster diode wiring kit for towed vehicles with the seven wire to six wire flexo-coil kit, part number is RM-15267.Now this wiring kit's going to be the perfect solution for towed vehicles. This is going to take a working seven pole plug and we're going to transfer that right back as if our Jeep we're a trailer. So anytime the blinkers, brakes, or running lights come on in our RV, that's going to be transfer back and we'll see it on the lights on our Jeep.Now let's test our lighting system out. You'll want to hook it up to either a tester or your motor home. Start by turning on our running lights. Then we do our left blinker, our right blinker.Now the diodes are going to play an important role in our towed vehicle wiring, these prevent backfeeding. more
4/12/2018 4:02:10 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2012 Jeep Liberty- Video
Today in this 2012 Jeep Liberty, we'll be having a look at and showing you how to install the Roadmaster diode seven-wire to six-wire Flexo-Coil wiring kit part number RM-15267. Here's what our diode wiring looks like installed. As you can see, we're utilizing our vehicle's factory taillight and brake light bulb in order to turn our Liberty into a trailer like vehicle to be towed behind our motor home. Our Liberty does have a separate terminal bulb from the factory but we're not utilizing that. We're using our taillight and brake light bulb to combine all of our functions into one bulb.By utilizing this dialed wiring, we don't have to worry about using magnetic tow lights, we utilize what our vehicle already has in place from the factory. So we only have to make a simple connection at the front of it when we're ready to flat tow. more
12/20/2017 10:17:10 PM
Roadmaster Universal Diode Wiring Kit Installation - 2007 Jeep Liberty- Video
Speaker 1: Today, on our 2007 Jeep Liberty, we're going to be taking a look at and installing the Roadmaster Universal high-power diode wiring kit, part number RM-152. Here's everything our kit's going to come with. It's going to come with four high-powered diodes, three feet of wire loom, 30 feet of four-wire wiring harness, several cable ties, a ring terminal, a butt connector, and a self-tapping screw.Our kit is going to combine our lights from our RV with our towed vehicle and have them act as one. When we're not towing our vehicle, the lights are going to act normal and not going to interfere with normal operation. Our diodes here are going to prevent any feedback back to our RV, and they're going to protect our vehicle and our lights and our wiring system from any damage that may occur.This kit is going to work with several adapter cords. We're going to be using it in conjunction with the seven to six wire, part number 98146-7. more
10/17/2017 3:43:54 PM
Hopkins Custom Tail Light Wiring Kit Installation - 2017 Jeep Cherokee- Video
Speaker 1: Today on our 2017 Jeep Cherokee, we're going to be taking a look at and showing you how to install the Hopkins custom taillight wiring kit for towed vehicles, part number HM56208. So here's what our wiring looks like once we have it installed. Do want to mention we chose to put a different style connector in the four pole flat, which is sold separately. What this is going to allow us to do is it's going to allow us to accept our RV's taillight signals, brake and turn signals and use them in conjunction with our vehicles taillights without having to worry about putting the magnetic lights on our vehicle.What you're really going to like about our wiring is that it's a custom fit for our vehicle, so we're not going to have to cut or splice into our factory wiring it's going to be a simple plug and play installation with a couple T connectors that are going to go in behind our taillights. As well as having a diode pack that's going to protect our vehicles wiring in case of any problems that may arise or a short circuits from the motor home. Now that we've gone over some of the features and seen what it looks like, show you how to get it installed.To begin our installation, we're going to open up our hatch. more
9/19/2017 11:32:09 AM
Roadmaster 4-Diode Universal Wiring Kit Installation - 2017 Jeep Wrangler Unlimited- Video
Speaker 1: Today on our 2017 Jeep Wrangler Unlimited, we're going to take a look at and also show you how to install the Roadmaster high powered diode kit with the seven wire to six wire straight cord. Part number is RM-152-98146-7.Now the reason to choose this style of the kit over a coiled wiring kit, would be because your tow bar either has a slot where your wiring will slide through to keep it really nice and neat. Or you prefer a nice neat look where you could zip tie everything together and keep it clean. The diodes are also an important part here protecting both the vehicle and your motor home from any kind of back feed between each other.Now to begin our installation, we're going to get our wiring ran kind of out here on the front of the vehicle, so we can install our plug. We just stretch our four pole wire out underneath the vehicle. We'll bring this up from behind. more
9/12/2017 12:35:57 PM
Tow Ready Tail Light Isolating Diode System Installation - 2017 Jeep Grand Cherokee- Video
Speaker 1: Today on our 2017 Jeep Grand Cherokee we're going to be taking a look at and showing you how to install the Tow Ready Taillight Isolating Diode System with Four Pole Connector, part number TR118821. This diode system is going to provide a proper lighting function for your towed vehicle. The diodes protect your RV from any back feed if there is a problem in the wiring from your vehicle, and vice versa. It's going to protect your vehicle from any back feed from the RV. Now let's show you how to get this installed.First thing we're going to do is we're going to start by removing our taillight. You take a trim panel tool, and you're just going to gently pull out on these pins until they come all the way out. more
8/7/2017 8:12:06 AM
Hopkins Tail Light Wiring Kit Installation - 2017 Jeep Wrangler- Video
Speaker 1: Today on our 2017 Jeep Wrangler we're going to be taking a look at and showing you how to install the Hopkins Custom Taillight Wiring for Towed Vehicles, part number HM56200. Here's what our wiring looks like fully installed. I do want to mention, we did cut off the four pole end that came with our kit, and we decided to put on a six pole round that is sold separately. Our wiring is going to let us flat tow our Jeep and safely get down the road and have all the required lights such as our clearance lights, brake lights, and turn signals.This is going to wire up our vehicle to accept lights that are coming from our RV and control the lights on our vehicle, so that when we're driving down the road everybody will know what's going on, whether we're slowing down and hitting the brakes or turning on our turn signals. Our wiring is custom, which means it's going to be made particular to your vehicle, and the connection points are going to connect behind the taillights here. It's also going to have a converter box with diodes in it that are going to protect our vehicle's electrical system from any feedback or anything that may go wrong on the RV end.Now, when we're not flat towing our Jeep, our Jeeps light's are going to work just like normal and they're not going to be affected at all. more
7/31/2017 4:57:06 PM
Roadmaster Universal Diode Wiring Kit Installation - 2017 Jeep Cherokee- Video
Today on our 2017 Jeep Cherokee we're gonna be taking a look at and showing you how to install the Roadmaster Universal High Powered Diode Wiring Kit, part number RM-152. In our case, we're also gonna be using the Roadmaster 7 Wire to 6 Wire Flexco Coil Kit, part number RM-146-7. Now our Roadmaster Diode Kit is gonna allow us to use our RV's tail lights, brake lights, and turn signals on our vehicle so that we can flat tow it safely down the road. To begin our installation we're gonna start on our passenger side here and we're gonna need to remove the two fasteners holding our tail light in place. Now I'm gonna be using a T30 torque bit to remove this. Now we're just gonna kind of give our tail light a good wiggle around to loosen it up a little bit. Then we're gonna pull straight back, which will release these tabs that are holding it in place. Now I'm gonna disconnect my socket from my tail light. There's gonna be a little button right here. more
6/28/2017 5:12:48 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2017 Jeep Cherokee- Video
Today, on our 2017 Jeep Cherokee, we're gonna be taking a look at showing you how to install the Roadmaster Diode Seven Wire to Six Wire Flexo Coil Wiring Kit, part number RM-15267. Now, our Roadmaster diode kit, it's gonna allow us to use our RV's taillights, brake lights, and turn signals on our vehicle so that we can flat tow it safely down the road. To begin our installation, we're gonna start on our passenger side here, and we're gonna need to remove the two fasteners holding our taillight in place. Now, I'm gonna be using a T30 Torx Bit to remove those . Now we're just gonna kinda give our tail light a good wiggle around to loosen it up a little bit, and then we're gonna pull straight back. Let's release these tabs that are holding it in place. Now, I'm gonna disconnect my socket from my taillight. more
6/28/2017 5:12:14 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2017 Jeep Wrangler Unlimited- Video
Today on our 2017 Jeep Wrangler Unlimited, we will be having a look at and installing the Roadmaster diode seven-wire to six-wire flexo-coil wiring kit, part number RM-15267, in conjunction with the Roadmaster battery charge line kit for towed vehicles, part number RM-156-25. Here's what our wiring looks like installed. You see we have a nice six-way round connector on the front of our Jeep, with a nice spring-loaded dust cover here, which snaps shut to keep the dirt and elements out of our connector when it's not in use. We have a seven-way RV connector that plugs in the back of our motor home, which adapts down to our six-way round right here. This will give us the umbilical connection that we need in order to transfer our lighting functions from the RV back to our Jeep, thus treating it as a trailer. The diodes that we are using with this kit make it so that we can utilize the vehicle's factory light bulbs and our tail-light assemblies. This way we're not adding an extra bulb to it, or using magnetic tow lights, which you see in a lot of vehicles being flat-towed behind motor homes. This is a nice, clean solution so you just have to plug one cable in between the mobile home and your Jeep when you're towing it, and you don't have to worry about removing lights and having a place to store them. more
6/26/2017 3:27:08 PM
Roadmaster Universal Diode Wiring Kit Installation - 2017 Jeep Wrangler Unlimited- Video
Speaker 1: Today on our 2017 Jeep Wrangler Unlimited we're going to show you how to install the Roadmaster Universal Hy-Power diode kit for towed vehicles, part number is RM-152. We'll also use the Roadmaster seven wire to six wire straight cord kit. This part number is RM-98146-7.To begin our installation, we're going to get our wiring ran out here on the front of the vehicle so we can install our plug. We just stretch our four pole wire out underneath the vehicle. We'll bring this up from behind. Now, this base plate kit recommended that we notch out a hole here to help with our wiring, which is a great idea. more
6/7/2017 12:02:07 PM
Hopkins Tail Light Wiring Kit Installation - 2017 Jeep Wrangler Unlimited- Video
Today on our 2017 Jeep Wrangler Unlimited, we'll be having a look at and installing the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles, part number HM56200. Here's what our wiring looks like installed. A nice 4-pole flat here in the front of our vehicle. With this applied dust cover, this will treat our Jeep like a trailer when it's towed behind our RV, giving us our, as required by law, lighting that we need. We'll have our turn signals, our lights, and our brake lights that we need in order to safely tow our vehicle. Now, what I really like about this kit compared to other kits on the market is that it's direct plug and play. There is no cutting, no splicing of your factory wiring; no drilling of holes in your tail light assemblies in order to add a separate bulb and socket. This will utilize factory style connectors plugged in line with your tail lights to the vehicle's wiring harness, has diodes built into it so there is no voltage being back-fed into your vehicle's sensitive electrical systems, and it utilizes the factory bulbs so it looks just like stock while it's rolling down the road. Now that we've going over some features of our Hopkins plug and play wiring kit, we'll show you how to get it installed. First thing we need to do in order to begin our installation is remove our tail light assemblies. more
4/5/2017 8:47:41 AM
Roadmaster Tow Bar Wiring Kit Installation - 2015 Jeep Wrangler- Video
Today on our 2015 Jeep Wrangler, we'll be having a look at and installing the Roadmaster Universal Hy-Power Diode Wiring Kit. Part number RM-154. With our Roadmaster Wiring Diode Kit installed on our Jeep, we don't have to worry about using magnetic tow lights when we're flat towing our Jeep behind our motor home. This would utilize our factory bulbs in the factory tail light assemblies, giving us all the functions that are required by law in order to safely flat tow our vehicle behind our motor home. We'll have our working tail lights, turn signals, and brake lights, treating our Jeep like a trailer behind our motor home. With these diodes, we don't have to worry about any voltage from the RV being back fed into the sensitive electronic components of our Jeep causing damage. Now that we've gone over some features, we'll show you how to get them installed. To begin our installation, we're going to start with swapping out our connector on the end of our wiring harness. more
2/24/2017 12:22:16 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2016 Jeep Cherokee- Video
Today on our 2016 Jeep Cherokee we're going to show you how to install the Roadmaster Flexo Coil Diode Wiring Kit for a seven pole to six pole connection. Part number is RM15267. The first thing I'm going to do is take my six pole plug, I'm going to take the provided screws here. I'm going to attach that plug right to the bracket. Once that's attached we'll pull the boot off the back, and we want to slide our wiring through the boot. Now, in typical applications here you're just going to have the four wires. more
2/16/2017 2:47:39 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2013 Jeep Wrangler Unlimited- Video
Today on our 2013 Jeep Wrangler Unlimited we'll be installing the Roadmaster Diode seven-wire to six-wire Flexo-coil wiring kit, part number RM-15267. All right, here's what the wiring looks like installed. As you can see it doesn't take up very much space on the front of the vehicle at all, tucks up nicely out of the way. This will allow us to safely flat-tow our vehicle behind our RV and have all of our factory lighting functions still work. We don't have to worry about using magnetic tow lights or having an extra set of lights added to the vehicle to tow it. This utilizes the factory light bulbs already in the vehicle utilizing diodes. more
1/12/2017 2:54:11 PM
TrailerMate Tail Light Wiring Kit Installation - 2015 Jeep Wrangler Unlimited- Video
Today on our 2015 Jeep Wrangler Unlimited Rubicon edition we are going to be taking a look at and installing the trailer mate custom tail light wiring kit for towed vehicles part number TM781124. Here's what this wiring is going to look like once it is installed on the vehicle. You've got your four flat connection here at the front which is going to provide you power and ground in order to power the lights at the rear of the towed vehicle with power coming from the motor home. It comes with a bracket to help you mount it, and it does also come with a dust cover to go over the four pull when not in use. This wiring kit teased directly into the factory connectors on the tail lights so there's no cutting or splicing required in order to install this system. It features built in diodes to help with overload protection and protect the vehicle's electrical system, and with this system you don't have to worry about it messing with the vehicle's electrical system when not being towed by the motor home. Now, let's go ahead and show you how to install it. To begin our installation, we are going to go ahead and route the four pull wiring from underneath the rear of our vehicle all the way up to the front where we will mount our electrical connection. more
11/28/2016 3:23:16 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2016 Jeep Wrangler Unlimited- Video
Today in our 2016 Jeep Wrangler Unlimited we're going to be taking a look at and installing the Road Master Diode Seven Wire to Six Wire FlexiCoil Wiring Kit. Part Number RM-15267. First thing we'll need to do to begin our install is we're going to need to remove this little cover right here and in order to do that there's going to be six total push pins. Four up along the front here and then two more along the backside that I'll show you. You can take a flat-head screwdriver. Just pop the center of those down. more
6/29/2016 12:34:06 PM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2007 Jeep Wrangler Unlimited- Video
Today on our 2007 Jeep Wrangler Unlimited, we'll be installing the Roadmaster Diode 7-Wire to 6-Wire Flexo-coil Wiring Kit. This is part number RM-15267. The Roadmaster tow bar wiring diode kit allows you to use your vehicle's tail lights and wiring system while preventing feedback from your RV. It lets you wire your vehicle to accept your RV's tail, brake and turn signal lights for flat towing. Here's what our kit consists of, the most important part being the four diodes that we're going to use to tap into our vehicle's stock wiring, so we can have towed vehicle lights behind our RV. We have a bundle of four pole flat wiring here. We'll run this to the front of our Jeep using this connector here, which is a six pole, where the flexo wiring here will connect to. more
6/27/2016 12:12:39 PM
Roadmaster Universal Diode Wiring Kit Installation - 2007 Jeep Wrangler Unlimited- Video
Today on our 2007 Jeep Wrangler unlimited, we'll be installing the Roadmaster Universal Hy-Power Diode Wiring Kit, part number RM-152. In conjunction with this, we'll also be using the Roadmaster 7-wire to 6-wire Flexo-Coil Kit, part number RM-146-7. The Roadmaster tow bar wiring diode kit allows you to use your vehicle's tail lights and wiring system while preventing feedback from your RV unless you wire your vehicle to accept your RV's tail brake and turn signal lights for flat towing. Here's what our kit consists of, the most important part being the four diodes that we're going to use to tap into our vehicle's stock wiring so we can have towed vehicle lights behind our RV. We have a bundle of 4-pole flat wiring here so we will run this to the front of our Jeep using this connector here, which is a 6-pole where the Flexo wiring here will connect to. Then we have the standard 7-way RV flat which will go in the back of the RV. We have several zip ties here to secure all of our wiring, and some wire loom mesh included as well in case we need to protect it from any moving parts or sources of heat. We also have an optional bracket here in case your tow bar base plate doesn't already have a spot to put your connector here, so this'll allow you to attach it. more
6/27/2016 12:11:43 PM
Hopkins Tail Light Wiring Kit Installation - 2016 Jeep Wrangler Unlimited- Video
Today in our 2016 Jeep Wrangler Unlimited, we're going to take a look at and also show you how to install the Hopkins custom tail light wiring kit for towed vehicles. Part number is HM56200. All right, now here's a great look at what our wiring kit's going to look like before we start installing it. You can see here's the heart of the system. This is a weatherproof sealed box. Inside, it contains diodes. Now, these diodes are designed to prevent back feeding, so we won't have any back feed coming from our RV into our towed vehicle, so we're not going to have to worry about any electrical issues there. Now, we've got our signal wire here. more
6/15/2016 11:35:37 AM
TrailerMate Tail Light Wiring Kit Installation - 2016 Jeep Wrangler Unlimited- Video
Today on our 2016 Jeep Wrangler Unlimited, we're going to be taking a look at, and also showing you, how to install the TrailerMate Custom Tail Light Wiring Kit for Towed Vehicles. This part number is TM781124. Here's what our kit's going to look like. Basically, this is going to provide us with the trailer signal that we need, or a plug-in, at the front of the vehicle to get the trailer signal from our motor home so it'll operate the lights on our vehicles we're heading down the road. That's going to keep us legal. You can see we've got a nice, long coil of wire so we can run from the front of the vehicle to the back. Once we get there, we've got a white ground. more
5/4/2016 10:54:42 AM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2012 Jeep Grand Cherokee- Video
Today, on our 2012 Jeep Grand Cherokee, we are going to be showing you how to install the Roadmaster 7-wire to 6-wire Flexo-Coil Diode Wiring Kit, part #RM-15267. Here is what our RM-15267 kit is going to look like. What we are going to have is a good 30 foot length of wire. This allows us to get from the front of the vehicle where we are going to be mounting our 6 pull plug right back to the vehicle's taillights where we want to send that signal. We've got diodes that are going to present back-feed from the car to the motorhome or from the motorhome to the car so it's a really nice, very well-protected system. Then, we've got the umbilical. more
4/20/2016 1:48:07 PM
Hopkins Tail Light Wiring Kit Installation - 2015 Jeep Wrangler Unlimited- Video
Today on this 2015 Jeep Wrangler Unlimited, we're going to review and install a Hopkins custom tail light wiring kit for towed vehicles. Part number HM56200. All right, this is what the wire harness looks like when it's installed on our Jeep. You can see it had its built in bracket here and a four pull cover for the four pull. Now, there's not much to see on this because everything else is installed inside the vehicle. Next, we'll go ahead and show you what all the parts that come with the kit. This is our main wire harness right here with diodes into converter, and you have two T connectors. more
4/7/2016 10:32:04 AM
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2015 Jeep Cherokee- Video
Today in our 2015 Jeep Cherokee, we'll be taking a look at and installing the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit, part number: RM-15267. Here's what it looks like once it's installed. It's is going to have the diodes to protect your electrical system in your vehicle. And it's going to make hooking up to your trailer very easily without having to run separate set of lights back to the end of the vehicle for your brake and turn signals.This is going to be installed at all times. And the only time it's going to be active is when you plug into your RV. What's nice about this kit is it has diodes. more
3/17/2016 3:37:50 PM
Roadmaster Universal Diode Wiring Kit Installation - 2015 Jeep Cherokee- Video
Today on our 2015 Jeep Cherokee, we'll be taking a look at and installing the Roadmaster Universal Hy-Power Diode Wiring Kit, part number RM-152.Here's what it looks like once it's installed. This is going to have the diodes to protect your electrical system in your vehicle. And it's going to make hooking up to your trailer very easily without having to run a separate set of lights back to the end of the vehicle for your brake and turn signals. This is going to be installed at all times. And the only time it's going to be active is when you plug in to your RV.And what's nice about this kit is it has diodes. So it's not going to allow anything to back feed into your car's electrical system, causing a short. more
3/17/2016 3:36:31 PM
Hopkins Tail Light Wiring Kit Installation - 2016 Jeep Wrangler- Video
Today on our 2016 Jeep Wrangler, we're going to show you how to install the Hopkins Custom Taillight Wiring Kit for Towed Vehicles, part number HM56200. What this is going to allow us to do is hook up our motor home, and it's going to operate the lights on the vehicle just as if we we're sitting inside the car turning the signals on. It does that with the diode converter here, so this box has built-in diodes. This is going to prevent any back feed into the electrical system of the towed vehicle, and the diodes are going to convert whatever signal it's getting from our taillights into a usable signal. That diode converter is going to take the signal coming in from the motor home, it's going to translate it into signals that the vehicle can use to operate its taillights. Great thing about it is when it's not connected to your motor home, there's going to be absolutely no interference. Now to begin our installation, we need to remove the driver's side taillight. more
12/22/2015 11:36:24 AM
Roadmaster Tow Bar Wiring Kit Installation - 2014 Jeep Wrangler- Video
Today on our 2014 Jeep Wrangler, were taking a look at in installing the Roadmaster Universal Hy-Power Diode Wiring Kit, Part Number: RM-154. The first thing that were going to want to do in the installation of our Hy-Power Diode Wiring Kit is going to be to remove the Phillips head screws here at the back of the taillight and remove the taillight assembly from the vehicle. Once you we have it removed from the backside of the vehicle, well go ahead and unplug the manufacturing wiring harness. To do so, depress the tab and pull out. Then well pull back the tape here and peel back the wire loom so we can expose these wires. Once we have the wires exposed, well go ahead and take a wire tester and test our circuits. Now go ahead and test our right turn signal. more
10/29/2015 10:22:07 AM
Hopkins Tail Light Wiring Kit Installation - 2008 Jeep Wrangler Unlimited- Video
Today on our 2008 Jeep Wrangler Unlimited we're going to show you the Hopkins custom taillight wiring kit for towed vehicles. Part Number HM56200. First off, we have this T-connector here, this one with the yellow wire goes to the left-hand side, or driver side. The T-connector here with the green wire goes over to the passenger side. This is our converter right here which takes our input from a 4 pole, that gets the power from the RV, goes through here and divides up to the wire harness, and to the tail lights. This long 4 pole wire harness will get ran underneath the vehicle all the way up towards the front, where it will be held in place by a spracket, also with its protective cover. more
8/8/2015 4:08:57 PM
Trailer Wiring Harness for Towed Vehicles Installation - 2005 Jeep Liberty- Video
Today on our 2005 Jeep Liberty, we're going to show you how to install the TrailerMate Custom Tail Light Wiring Kit for Towed Vehicles. This is part number TM781104. Here's what your harness is going to look like when you receive it. You're going to get a nice quantity of zip ties. We're going to have our small extension which will extend our plug out to where we can get it to our vehicle. We have our mounting bracket for it, a couple of small screws to help us secure that and even a couple of the padded cable hold downs, be able to zip tie our wire to once we run it to the front of the truck. You see the one here that's got yellow, brown, white and red This is going to go inline behind our driver side tail light. more
7/15/2015 10:57:46 AM
Filter Videos
Filter Videos
