Trailer Wiring Harness Installation - 2007 Jeep Commander- Video
Today on our 2007 Jeep Commander, we have our Tow-Ready Trailer Wiring Kit, part number 118408. Now, what comes in our kit, we have our module that has our trailer plug on it, come over here, we've got our driver's side plug and play, it fits in there as a, "T," and we've got our passenger side, again it fits in there as a, "T," and we've got extra wire, because we'll be running it through our bumper back here. Also, a couple zip ties and our self tapping screw. That's for our ground wire on our module. On the back of our module, we have our sticky pad I put on already so that we're ready to stick it in place as soon as we're at that point. First thing we need to do, is we'll remove our 2 pins that holds the light in place. I've got my remover tool, if you don't have a remover tool, it looks like a Flathead will work just fine, you just got to be careful you don't break these pins, because we'll need to reuse them. more
12/9/2015 9:18:07 AM
Trailer Connector Socket Installation - 2014 Jeep Grand Cherokee- Video
Today on our 2014 Jeep Grand Cherokee we're going to show you how to install the Hopkins Pollak 7- and 4-Pole Trailer Connector Socket with Mounting Bracket, part number HM40975. Here's what the wiring kit is going to come with. We're going to have a nice mounting bracket here. It's going to have a couple of pre-drilled holes there. We typically can use these self-tappers to go right up through. On the Grand Cherokee we don't have a good solid surface so we've got a bracket to take care of that, we'll show you in just a minute. The plug itself is really neat. more
11/4/2015 2:41:06 PM
Trailer Wiring Harness Installation - 2015 Jeep Wrangler Unlimited- Video
Today on our 2015 Jeep Wrangler Unlimited we'll be taking a look at and installing the Curt-T connector vehicle wiring harness with 4-pole flat trailer connector, part number C55124. First thing we're going to do on our installation of our wiring harness is go ahead and remove the driver's side rear taillight assembly. To do so there's going to be two Phillip's screws here on the inside that we're going to remove. You can leave the outward ones installed, since those are securing the cover to the light assembly here. Once you have those two removed we'll be able to pop the taillight assembly right out, just like so. Then we'll disconnect the wiring harness, press down on the tab on the bottom and pull out. Once we have it disconnected we'll go ahead and set the taillight off to the side, and bring in our wiring harness. We're going to simply plug in the same kind of connector to our factory harness. more
11/3/2015 11:26:14 AM
Trailer Wiring Harness Installation - 2015 Jeep Cherokee- Video
Today on our 2015 Jeep Cherokee we're are going to take a look at and show you how to install the tow ready T1 vehicle wiring harness with the 4-pole flat trailer connector. Part number is 118605. Here your going to see what the wiring kit looks like when you pull it out of the box. We've got our yellow and brown side. This is going to connect directly between our factory connection points behind the driver side taillight. The greens going to run over and do the same thing behind the passenger side taillight. more
10/21/2015 3:27:45 PM
Trailer Wiring Harness Installation - 2014 Jeep Grand Cherokee C55384- Video
Today is 2014 Jeep Grand Cherokee. We're going to show you the CURT T-Connector Vehicle Wiring Harness for factory tow packages. Part number C55384. Okay. This is what you get with the part number, this is the wire harness that plugs into the factory port on the vehicle and then it comes out to the other end, a four-pole flat. This is our cover, it goes with the four-pole and also comes with some zip ties as well. All right. more
8/21/2015 3:42:40 PM
Trailer Wiring Harness Installation - 2010 Jeep Grand Cherokee- Video
Today on this 2010 Jeep Grand Cherokee we're going to show you the Curt T-connector vehicle wiring harness with a 4-pole flat, part number C56009. This is parts that you get with this part number. This is your wire harness here and this is one of the T-connectors. This T-connector goes over to the driver's side tail light. We got a second one that goes over to the passenger's side tail light. We have a white wire for ring terminal and that will go to ground on a sheet nail 00:00:27 behind the passenger's side tail light. more
7/28/2015 2:02:31 PM
Trailer Wiring Harness Installation - 2015 Jeep Cherokee c56208- Video
All right, today in this 2015 Jeep Cherokee, we're going to install a Curt T Connector Vehicle Wiring Harness, part number C56208. We'll go ahead and lay out our parts before we install it. This is our wire harness right here, and this is one of the T connectors. The T connector with the yellow wire goes to the driver side, T connector with the green wire goes over to the passenger side. We also have the black wire that gets connected up to an extra length of wire here, that eventually gets rammed to the battery. Once we get to the battery, it has a fuse holder right here, and also has a small parts kit with a fuse, some zip ties, and adhesive for the module as well. We'll go ahead and take the pan on the bottom and raise it up. more
7/28/2015 10:56:06 AM
Trailer Wiring Harness Installation - 2015 Jeep Patriot C56162- Video
Today on our 2015 Jeep Patriot, we're going to show you how to install a Curt T-Connector vehicle wiring harness with the four fold flat trailer connector part number is C56162. Here's what the wiring kit is going to look like. We've got our yellow, brown and white wire, this plugs in behind the driver side tail light. We've got our ground wire. We're going to find either a existing medal stud or we'll use a self tapping screw to ground that out. This is our module box. more
7/8/2015 1:06:57 PM
Trailer Wiring Harness Installation - 2006 Jeep Liberty- Video
Today, we're going to show you a Curt T-connector Vehicle Wire Harness with a four-pole flat trailer connector, part number C55382. These are parts you get with this part number. First up, here's our T-connector right here. All right This T-connector with the yellow wire. This one always goes toward the driver side of the vehicle. It also has a red matching locks on there and matches the factory connection points on the wire harness. more
7/1/2015 12:06:15 PM
Trailer Wiring Harness Installation - 2015 Jeep Grand Cherokee- Video
Today on our 2015 Jeep Grand Cherokee, we're going to review and install the Curt T-Connector Vehicle Wiring Harness with a 5-Pole Flat Trailer Connector, part number C56515. Here's what our 5-flat harness is going to look like once it's installed. The 5-flat harness will have a running, turn and brake signal circuits and the reverse light circuit. This will allow you to duplicate the signals coming from the vehicle to our trailer or towing product. Note the reverse light will then activate on your trailer or, more specifically, for a hydraulic lockout circuit like on boat trailers. Note the 5-flat trailer connector can work in conjunction with just a standard 4-flat trailer connection. We just simple don't use the 5th pole, which is for the reverse tail lights. more
6/26/2015 2:43:01 PM
Trailer Wiring Harness Installation - 2015 Jeep Grand Cherokee C55384- Video
Today on our 2015 Jeep Grand Cherokee, we're going to review and install the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C55384. Here's what our Curt T-connector 4-flat wiring harness will look like once it's installed. Our f-flat connector is a standard-sized trailer and accessory application. It provides the running, turn, and brake signal circuits, duplicating what happens on the vehicle on our trailer or accessory. Next we'll go ahead and show you the minimum tools required for installing the trailer connector. Use a flat blade or trim-panel tool and just a socket and ratchet for tightening down our hardware. Now we'll go ahead and show you how easy it is to install. To being our install, we first need to locate the vehicle's 7-pole connector wiring harness. more
6/26/2015 2:42:47 PM
Trailer Wiring Harness Installation - 2015 Jeep Grand Cherokee 118384- Video
Today on our 2015 Jeep Grand Cherokee, we're going to review and install the tow ready T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number 118384. The 4-flat trailer connector is a standard trailer and accessory connection point. This will duplicate the vehicle's running, turn, and brake signal circuits. Everything that happens on the vehicle, will get duplicated on your towing product or accessory. Next we'll go ahead and show you the minimum tools required for installed the trailer connector. Use a flat blade or trim panel tool and just a socket and ratchet for tightening down our hardware. Now I'll go ahead and show you how easy it is to install. To begin our install, we first need to locate the vehicle's 7-pole connector wiring harness. The manufacturer's 7-pole round trailer connector is attached to the rear fascia. more
6/26/2015 2:42:32 PM
Trailer Wiring Harness Installation - 2015 Jeep Grand Cherokee HM40975- Video
Today on our 2015 Jeep Grand Cherokee, we're going to review and install the Pollak 7- and 4-Pull Trailer Connector-Vehicle End, part number HM40975. Here's what our Pollak 7-pull and 4-flat trailer connector looks like once it's installed. This is our vehicle side, so everything that the vehicle does, like running, brake, or turn signal circuits, will get duplicated here at our trailer connector, and sent out to our trailer or towing product. On one side, we have a 7-round, or 7-blade, style trailer connector. On the other side, we have the standard 4-flat trailer connector. This can be used in a variety of applications, and covers a majority of the trailer and towing products on the market today. Next we'll go ahead and show you the minimum tools required for installing the trailer connector. more
6/24/2015 10:56:27 AM
Trailer Wiring Harness Installation - 2014 Jeep Wrangler Unlimited- Video
Today on our 2014 Jeep Wrangler Unlimited, we're going to review and install the Tow Ready Custom Fit Vehicle Wiring Harness with 4-Pole Trailer Connector, part number 118416. Now here's what our 4-flat trailer connector's going to look like once it's installed. To use it, we'll simply remove the cap, and take it out of the chain hold down. We can then plug it into our trailer. The 4 flat connectors can provide ground, running, turn, and brake signals. The yellow is for the driver's side, and the green is for the passenger's side. more
5/29/2015 8:37:12 AM
Trailer Wiring Harness Installation - 2011 Jeep Grand Cherokee- Video
Today in our 2011 jeep grand cherokee we're going to show you how to install the curt t connector vehicle wiring harness with the 4 pole flat trailer connector. It's part number of C56009. All right guys, here's what the wiring harness for the jeep's going to look like. Super simple easy thing to set up. The yellow and ground, that's going to go behind our driver side taillight housing. It's going to run over here to the middle where it goes into our 4 pole plug. Then from our 4 pole plug we'll have the green and white wire. more
5/26/2015 12:11:56 PM
Trailer Wiring Harness Installation - 1997 Jeep Wrangler- Video
Today on our 1997 Jeep Wrangler, we're going to be installing the T1 Vehicle Wiring Harness with the 4 pull flat trailer connector. Part number is 118356. Now right in here in the rear corner of the vehicle both in the driver's side and passenger side there's going to be this little plastic panel. What we want to do, there's a little push fastener right here. We're going to pull that out, and that'll allow us to drop this cover down, and we'll get it out of the way far enough to where we can get up inside here and work. What we're looking for inside is going to be this plug right here. more
5/11/2015 8:48:28 AM
Trailer Wiring Harness Installation - 2013 Jeep Grand Cherokee- Video
Today on our 2013 Jeep Grand Cherokee, we're going to review and install the Curt Custom Vehicle Wiring Trailer Connector, part number C56009. Now to begin our install, we're first going to open up the rear hatch. We need to remove both rear tail light assemblies. Each tail light assembly is secured with two fasteners. These are pushpin fasteners, so we're going to pry the center of the fastener out, and then remove it completely. Just using a flat blade screwdriver, we can get underneath that center, just work it out. Note, if you have an interior trim panel tool, it can help to get underneath the head of the fastener, prying it out. Once you have it pried out, you can remove the whole fastener. more
5/4/2015 3:30:35 PM
Trailer Wiring Harness Installation - 2013 Jeep Grand Cherokee 118425- Video
Today on our 2013 Jeep Grand Cherokee we're going to review and install the Tow Ready T-One Vehicle Wiring Harness with 4-pole flat trailer connector, part number 118425. Now to begin our install we're first going to open up the rear hatch. We need to remove both rear taillight assemblies. Each taillight assembly is secured with two fasteners. These are push pin fasteners so we're going to pry the center of the fastener out and then remove it completely. Just using a flat-bladed screwdriver, we get underneath that center, just work it out. more
5/1/2015 10:51:06 AM
Trailer Wiring Harness Installation - 2015 Jeep Wrangler Unlimited 118416- Video
Today on our 2015 Jeep Wrangler Unlimited we'll be installing the Tow Ready T-One vehicle wiring harness with 4-pole flat trailer connector, part number 118416. Now to begin our install we're going to start here at the rear of the vehicle, removing the driver's taillight assembly. We'll remove the two inside screws that hold the assembly in place. Once we have the fasteners out we can go ahead and pop the taillight assembly, exposing the manufacturer's wiring underneath. Next I'm going to go ahead and remove the taillight assembly completely by pressing on the locking tab and separating the two connectors. We can take the taillight assembly and set it aside for reinstallation later. Next we're going to bring in our new wiring harness. more
4/13/2015 8:43:28 AM
Trailer Wiring Harness Installation - 2014 Jeep Patriot C56162- Video
Today on our 2014 Jeep Patriot, we're going to be installing the Curt T Connector Vehicle Wiring Harness with the four pole flat trailer connector, part number C56162. We'll begin by opening our rear hatch up and we're going to remove the two push pin connectors located here on the passenger side and in the same spot on the driver's side. A small screwdriver, if you have it a small pick is really all you need to just kind of pry the center of that fastener up and then we'll pull the main body of it out. We'll do it for both connection points on this side. Sometimes the centers will pop out. Not a big deal, you can just poke it right back in there. Now at this point, it's going to tell you to remove both rear lenses and unplug the connectors from the rear. We're going to do them one at a time. more
3/20/2015 12:35:58 PM
Trailer Wiring Harness Installation - 2009 Jeep Grand Cherokee- Video
Today on this 2009 Jeep Grand Cherokee, we're going to show you part number 118425. This is the T-one vehicle wiring harness with a four pull flat trailer connector from Tow Ready. First we'll go ahead and show you the layout of our components. We've got a T connector here with the yellow wire, this will fit in between the wire harness at a junction point behind the tail lights, this is for the left hand side. We have the same assembly over for a right hand side in green wire. There's really no other component but the four pull flat right here. more
2/17/2015 3:32:48 PM
Trailer Wiring Harness Installation - 2003 Jeep Grand Cherokee- Video
Today on our 2003 Jeep Grand Cherokee we're going to be installing the Tow Ready T-One vehicle wiring harness with a 4-pole flat trailer connector, part number 118369. To begin our installation we're first going to need to raise the rear hatch of the vehicle. We're then going to need to remove a few of the interior panels in order to gain access to the plug. Next we're going to need to pop this panel here and this panel here loose because the plug we're looking for is actually right up underneath this in this area here. Just going to use a trim panel removal tool, or a large flat head screwdriver will work as well. Now with our interior panel pulled back we'll need to fold this cover piece back too, but see this green piece right here This is the connector that you're looking for so that's what we'll be tying in with. Now here's what our t-connector wiring looks like. more
1/5/2015 2:43:39 PM
Trailer Wiring Harness Installation - 2006 Jeep Commander- Video
Today on our 2006 Jeep Commander, we'll be installing the tow ready T1 connector wiring kit, part number 118408. To begin with, we'll go ahead and raise the rear hatch of the vehicle. We'll need to remove these two push fasteners from each side's light assembly so we can pull the light assembly out, where we'll make our connections. We'll go ahead and start here on the driver's side. Go ahead and remove the two push fasteners. Do this by using a flat head screw driving and a trim panel removal tool. With the two fasteners out, we can go ahead and pop the whole light assembly out. more
12/22/2014 1:23:53 PM
Trailer Wiring Harness Installation - 2004 Jeep Wrangler- Video
Today on our 2004 Jeep Wrangler, we'll be installing the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C55363. Now, to begin our install, we'll first go underneath the driver side taillight assembly and locate the plastic cover that covers up the rear portion of the body. Once we locate the plastic flap, we'll need to peel it back, but before we do that, there's a push-pin fastener that need to pulled. You can use a flat-blade screw driver or plastic trim panel tool just to pry that plastic fastener out, and we'll pull a bit down on the flap. Once we have it down, we can expose the manufacturer's electrical connector here and note that it sometimes can be wrapped in foam to help protect it from the outside elements. Since this one's already been removed, we're going to press on the connector lock and separate the two connectors. There it goes. more
11/20/2014 11:45:33 AM
Trailer Wiring Harness Installation - 2007 Jeep Wrangler- Video
Today, on our 2007 Jeep Wrangler, we're going to be installing the Curt Custom Fit Vehicle Wiring Harness with a 4-Flat Trailer Connector, part #C55124. Here's what our current wiring harness looks like. We're over here on the drivers side taillight area. This is the only taillight that we will need to remove in order to make our connections. To remove the taillight, we'll need to remove this screw here and this screw here. We'll be using a Phillips head screwdriver to do that. With the two screws removed simply slide the taillight assembly out. We're going to need to unplug the factory wiring. more
11/19/2014 9:30:42 AM
Trailer Wiring Harness Installation - 2010 Jeep Grand Cherokee 118425- Video
Today on our 2010 Jeep Grand Cherokee, we'll be installing the Tow Ready T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number 118425. To begin our install we'll first need to open up the rear hatch. Each taillight is secured with 2 fasteners. These are pushpin fasteners that we can take a flat-bladed screwdriver, simply pry out on the center of the fastener to release it, and then remove it. Once we have both fasteners out, we can go ahead and remove the rear taillight assembly. As you remove it be careful not to break the alignment tabs underneath. more
11/14/2014 10:11:13 AM
Trailer Wiring Harness Installation - 2005 Jeep Liberty- Video
Today on our 2005 Jeep Liberty, we'll be installing the Curt Custom Fit Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C55382. Now to begin the install of our new wiring harness, we'll first go ahead and open up the rear cargo door and then remove the driver and passenger's side taillight assemblies. To remove the taillight assemblies, we'll remove the two fasteners that secure the plastic housing to the body of the vehicle. Then pop the rear taillight assembly out of place being careful not to break the alignment tabs underneath. Now with the passenger's side done, I'm going to move over to the driver's side and repeat the same process. We just need to work through the rear door hinge to access the two fasteners. Once they're out, to assist in remove the taillight assembly, we can also use a plastic pry tool or a flat blade screwdriver just to pop the alignment tabs out being careful not to break them. Next we'll remove the taillight assemblies, to remove the taillight assembly we'll go ahead and unlock the red locking tab then press on the connector lock and remove it from the back of the taillight assembly. more
11/12/2014 1:51:58 PM
Trailer Wiring Harness Installation - 2010 Jeep Patriot- Video
Today on our 2010 Jeep Patriot, we will be installing the Curt T-Connector Wiring kit, part number C56162. We'll begin by opening the rear hatch doors on our Jeep. As you can see, we've already got our wiring kit laid in here. We're going to remove the pushpins that are holding our taillights in place. We'll now come to the passenger's side and remove the two that are located here as well. With the two pushpins removed we're going to come around the edge of our taillight here, we want to pop that out, being careful not to damage the tabs there or here. more
10/29/2014 9:10:14 AM
Trailer Wiring Harness Installation - 2007 Jeep Liberty- Video
Today on our 2007 Jeep Liberty, we'll be installing the Tow Ready T-One Connector, part number 118524. Now this particular vehicle already has some additional wiring installed that will allow it to be towed behind a motor home so we're going to do things a little different on this one. Because we know we cannot pull the taillights completely off on this vehicle, we're going to go ahead and run the green wire with the two connectors over to the passenger's side leaving the box as well as the yellow, the small red and the ground wire over on the driver's side. We'll run the wire underneath the lower rear bumper fascia. Securing it with zip ties and running it behind some of the brackets that hold the rear bumper on. Now that we have it over to the passenger's side, we'll go ahead and remove the passenger's side rear taillight by first opening up the rear hatch of the vehicle and then removing the two Torx head screws shown here. Now that we have these two screws out, we'll go ahead and pull the light assembly out. more
10/24/2014 1:15:51 PM
Trailer Wiring Harness Installation - 1999 Jeep Cherokee- Video
Today, on our 1999 Jeep Cherokee, we'll be installing the tow-ready T-1 connector, part number 118354. We'll go ahead and show you how to use the new 4 pole connector. We'll simply take it, run it to the center of the vehicle and out, staying away from the latch as pinching the wire off in the latch can harm it. However, the weather stripping is thick enough that it won't, and we'll simply close the rear cargo door on the wire. Then, we can go ahead and pull out the new 4 pole wire as necessary to go down to the hitch or accessory. Then, once we're finished using our new 4 pole wire, we'll simply role it up and store it underneath the spare tire. To begin our install, we'll first open up the rear cargo door. more
9/30/2014 6:18:16 PM
Trailer Wiring Harness Installation - 2014 Jeep Grand Cherokee C55515- Video
Today, on our 2014 Jeep Grand Cherokee, we're going to install the Curt T-connector vehicle wiring harness with 4-pole flat trailer connector. Part number C55515. To begin our install, we'll first locate the manufacturer's tow connector wiring harness. When we follow the manufacturer's wiring harness here, down the back of the vehicle, and to the back of the fascia, we can grab the round wiring connector and pull it free. Once we have access to it, we'll press on the connector lock and remove the weather pack plug that keeps it clean and free of dirt, dust, debris, and moisture. Once we have it removed, we'll go ahead and take our new harness, match it up with the manufacturer's, and install the new connector. Note, I do recommend to use some of the Edelmann Dielectric Grease on the connector. Part number 11755. more
9/29/2014 2:11:21 PM
Trailer Wiring Harness Installation - 2012 Jeep Wrangler- Video
Today on our 2012 Jeep Wrangler we're going to be installing the CURT t-connector vehicle wiring harness, part number C55124. Now we're going to begin over here on the driver side taillight. We're going to need to remove the four screws that secure the taillight to the vehicle. To remove them we'll be using a Phillips head screwdriver. We'll then slide the taillight assembly out from the body. You'll notice that there's a couple tabs here on the backside that help hold it in place. We're then going to need to disconnect the factory wiring from the backside of the taillight. more
9/25/2014 6:58:24 PM
Trailer Wiring Harness Installation - 2014 Jeep Cherokee- Video
Today, on this 2014 Jeep Cherokee, were going to install part number C56208 from Curt. This is the Curt T-connector vehicle wiring harness with a four-pole flat. Were going to need to get access back on the taillights so were going to have to open the back hatch. Now, our next step is very important. Well go to underneath the hood and disconnect the battery. Those electronics in this vehicle are so sensitive but this is essential to do this part. Well loosen up the negative terminal and just pull it off. more
9/12/2014 3:06:55 PM
Trailer Wiring Harness Installation - 2012 Jeep Grand Cherokee- Video
Today on our 2012 Jeep Grand Cherokee we'll be installing the Curt T-Connector Vehicle Wiring Harness with 4 Pole Flat Connector, part number C56009. To begin our install we'll first open up the rear hatch and remove the tail lights. To remove the tail lights we'll need to remove the two pushpin fasteners that secure the tail light housing. Taking a flat blade screwdriver we can get underneath the center of the tab, prying it up. Once we have it pried up we can then go ahead and remove the fastener. Then we'll go ahead and remove the tail light assembly. more
9/9/2014 4:01:00 PM
Trailer Wiring Harness Installation - 1998 Jeep Cherokee- Video
Today on our 1998 Jeep Cherokee we'll be installing the Tow Ready T-One Connector. Part number 118354. To install our new connector we'll first need to open up the rear cargo area. Then we'll remove the spare tire bracket. Then we'll remove the six screws securing the rear threshold, and the three screws securing the driver's side rear quarter panel. Next we'll identify the plug we'll be plugging inline with at the manufacturer's harness. This will be the white plug closest to the rear cargo door. Before I make my connection I'm going to go ahead and start routing my wire back in behind the interior trim panel. Now with my wire fed over to the connector, we'll simply press on the locking tab and disconnect the two manufacturer's connection points. more
8/11/2014 9:45:50 AM
Trailer Wiring Harness Installation - 2000 Jeep Grand Cherokee- Video
Today on our 2000 Jeep Grand Cherokee, well be installing the T1 Vehicle Wiring Harness with a 4-pole flat connector part number 118369. Well start by gaining access to the back of the vehicle and removing this trim panel. To pop the back of the trim panel loose, you have to loosen the screw that holds in the cargo hook and also the screw on the threshold. With those screws removed, just grab a hold of this trim panel and pull out. Theres a couple push fasteners that hold it in place and pull that back. Well move to the front of the panel and remove the last tow hook. With that cargo hook removed, the panel will just slide out of the way. more
7/25/2014 2:37:47 PM
Trailer Wiring Harness Installation - 2001 Jeep Cherokee- Video
Alright today in this 2001 Jeep Cherokee, we're going to install part number 118354, from Tow Ready. First thing we need to do is go ahead and open up the back hatch, and remove the spare tire. After the spare tire is removed, we'll go ahead and remove the threshold as well. Okay, now we also have to remove the spare tire stand as well. Then we ahead and start work on pulling back the interior panel. Alright, once we have the panel pulled out of the way, we can see a row of connectors. The connector that's closest to the end of the vehicle is the one we want to plug into. So we'll disconnect it, and the install the T connector. Then we'll go ahead and locate the factory ground wire, and we'll attach a white wire at the ring terminal to there. Once we clean off the location for our converter box, we'll go ahead and remove the adhesive backing an install it. Now I go ahead and reinstall the interior panel, and the components, as well as the spare tire components. With that, that finishes our install. Now go ahead and show you how to use the four pull harness, it's stored inside the vehicle until it needs to be used. Next we'll pull out a little bit of the harness, and shut the hatch on it. Then we'll pull out what we need to go to our trailer. more
7/15/2014 1:35:24 PM
Trailer Wiring Harness Installation - 2014 Jeep Wrangler Unlimited C55124- Video
Today on our 2014 Jeep Wrangler Unlimited, we will be installing Curt T-connector Vehicle Wiring Harness, Part No. C55124. To begin our install, we'll first go ahead and remove the tail light assembly for the driver side. To remove the tail light assembly, there are two inside screw fasteners that'll need to be removed. Once we've removed these fasteners, we can go ahead and gently pop the tail light assembly out of its position and remove it completely by pressing on the wiring connector lock and removing the wiring harness from the connector. We'll go ahead and set the tail light assembly aside. Next, we'll take the 4-pole connector, drop it down to where we can pull our 4-pole connector out from underneath the vehicle. Next, we'll take the white wire with the pre-test 00:00:45 ring terminal on our wiring harness which will be the ground wire for our new 4-pole connector and secure it directly to the frame or body of the vehicle, using a self-tapping screw. It's a great location where the sheet metal doubles up for a secured round. We can now go ahead and take the T-connector and plug it into the manufacturer's wiring. One side into the manufacturer's wire, the other side into the tail light assembly. more
6/4/2014 12:27:54 PM
Trailer Wiring Harness Installation - 2004 Jeep Grand Cherokee- Video
Today on our 2004 Jeep Grand Cherokee well be installing the Tow Ready T1 vehicle wiring harness, part number 118369. To begin our install well first open up the rear hatch. Then well remove the spare tire cover. Now it may not be necessary to completely remove the spare tire, but youre definitely going to want to shift it out of the way to gain access to two of the four rear threshold fasteners. Now were ready to remove the threshold fasteners. Once we remove these four screw fasteners well sit the fasteners and threshold aside. more
3/24/2014 9:10:28 AM
Trailer Wiring Harness Installation - 2014 Jeep Cherokee 118605- Video
Today on our 2014 Jeep Cherokee, well be installing the tow-ready T-One Vehicle Wiring Harness with four-pole connector part number 118605. Now, to begin our install, well first go ahead and open up the rear cargo door. Then, well remove the spare tire wheel cover. Then well remove the cargo hooks here at the threshold. To remove them, well have the first pop-up plastic cap and then remove the Torx bit screw underneath. Now with those removed, we can remove the rear threshold by gently prying up on the threshold and releasing the fasteners underneath. Well set the threshold aside. Next, well remove the plastic surround in the spare tire wheel. more
2/17/2014 8:39:43 AM
Trailer Wiring Harness Installation - 2008 Jeep Liberty C56183- Video
Today in our 2008 Jeep Liberty, we'll be installing the CURT T-connector Wiring Harness with 4-Pole Flat Trailer Connection, part number C56183. To begin our install, we'll first open up the rear hatch. There are two screws for each assembly. We'll go ahead and remove the screws and then pop the assembly out of its position being careful not to break the alignment tabs underneath. Then, we'll go ahead and press on the wiring connector and remove it from the taillight socket, setting the taillight aside. Now with the driver side done, I'll go ahead and repeat the same process on the passenger side. Next, we'll take our new CURT wiring harness and feed the green wire connector down between the bumper cover and body or sheet metal of the vehicle. more
11/25/2013 7:32:53 AM
Curt Trailer Wiring Harness Installation - 2012 Jeep Compass- Video
Today on our 2012 Jeep Compass well be installing a Curt tee connector vehicle wire harness with four poll flat connector, part number C56129. To begin our install well first open up the rear hatch and then well need to remove the rear taillight assemblies. Starting here on the drivers side, well go ahead and remove the two fasteners that secure the rear taillight assembly. To remove the fasteners well use a flat blade screwdriver and pry out on the center section and then remove the entire piece. Note: This is a two piece fastener so the center section can be completely out and then remove the second half. Now with the fasteners out of the way we will go head and gently pop the rear taillight lens towards the rear of the vehicle releasing the fasteners underneath, here and here. more
10/22/2013 9:42:10 AM
Trailer Wiring Harness Installation - 2011 Jeep Wrangler- Video
Today on our 2011 Jeep Wrangler, we're going to install part number C55124 from Curt. This is a Curt T-Connector Vehicle Wiring Harness. To start off our install, we're going to have to get behind the driver's side tail light. We need to remove the tail light from the vehicle. There are four screws that we have to remove. Once we have the guard off the light, we can remove the light itself from the body. Pull it away and you can see where the wire harness connects into the back of the tail light. more
10/3/2013 8:02:48 AM
Trailer Wiring Harness Installation - 2013 Jeep Wrangler 118416- Video
Today on our 2013 Jeep Wrangler Unlimited well be installing Tow Ready T-1 connector, part number 118416. To begin our install well need to remove the drivers side taillight assembly. Well remove the two inside screws and then pop the taillight assembly out of its position. Here we can gain access to the manufacturers wiring and well disconnect the taillight assembly from the wiring by pressing on the locking tab and pulling the connectors apart. Next, well set the taillight assembly aside and take our Tow Ready Harness and feed it down through the opening and then underneath the foam cover at the bottom of the drivers side quarter panel. This will feed our four pole underneath the vehicle. more
9/27/2013 8:31:08 AM
Trailer Wiring Harness Installation - 2012 Jeep Liberty- Video
Today on our 2012 Jeep Liberty well be installing the Tow Ready T1 connector, part number 118554. First to begin our installation well open up the rear cargo door. Well need to remove the fasteners that secure the taillight housing in place. Starting here on the drivers side, well go ahead and remove the two fasteners and then gently pry the taillight housing away from its current position, being careful not to break the alignment tabs underneath. Now well go ahead and remove the taillight assembly by pressing on the locking tab for the connector and removing it from the assembly. Well go ahead and set it aside for reinstallation later. more
3/26/2013 10:33:19 AM
Trailer Wiring Harness Installation - 2013 Jeep Wrangler Unlimited- Video
Today on our 2013 Jeep Wrangler Unlimited well be installing Tow Ready T-1 connector, part number 118416. To begin our install well need to remove the drivers side taillight assembly. Well remove the two inside screws and then pop the taillight assembly out of its position. Here we can gain access to the manufacturers wiring and well disconnect the taillight assembly from the wiring by pressing on the locking tab and pulling the connectors apart. Next, well set the taillight assembly aside and take our Tow Ready Harness and feed it down through the opening and then underneath the foam cover at the bottom of the drivers side quarter panel. This will feed our four pole underneath the vehicle. more
3/25/2013 11:41:14 AM
Trailer Wiring Harness Installation - 2012 Jeep Wrangler Unlimited- Video
12/19/2012 2:17:00 PM
Trailer Wiring Harness Installation - 1993 Jeep Grand Cherokee- Video
Today, on this 1993 Jeep Grand Cherokee, were going to install part number 118348 from Tow Ready. First thing well do is go ahead and remove the spare tire and remove the thresh hold at the bottom. Now, well go ahead and loosen up the side panels as well. Well also remove the small panel behind the spare tire. Now, well go ahead and start installing our T1 connector. On our passenger side, well go ahead and run the T connector with the green and red wires. more
12/17/2012 4:16:27 AM
Trailer Wiring Harness Installation - 2011 Jeep Wrangler 118416- Video
Today on this 2011 Jeep Wrangler were going to install part number 118416 from Tow Ready. This is our T1 wiring harness. The first thing we need to do is go ahead and remove the taillight on the drivers side. There are two screws we have to remove and then the light can be detached from the vehicle. Next well disconnect the wire harness from the light. Theres a small tab we have to push down and then you can pull it apart. more
11/21/2012 3:20:41 AM
Trailer Wiring Harness Installation - 2008 Jeep Commander- Video
Today on our 2008 Jeep Commander, we are installing the Tow-ready T1 connecter, part number 118408. To install our new fore pole we'll simply open up the rear cargo door and remove the two fasteners securing the driver's side tail light housing. We'll simply take a flat-bladed screwdriver and pry out on the center of the fastener and then remove it. Now you want to pop the rear tail light assembly out carefully. You may need to pry it gently but be careful not to break the alignment tabs underneath. Now with the drive's side rear tail light assembly removed, we can go ahead and press on the locking tab for the manufacturer's wiring connector and remove it. more
10/4/2012 5:22:27 PM
Filter Videos
Filter Videos
