Do the Curt and Hidden Hitches Available for 2008 Acura MDX Require Rear Bumper Trimming
Question:
2008 Acura MDX . does the Curt or Draw-Tite need a new bumper trim that the Acura factory hitch requires ? . on some of the hitches the trailer wires you open the tailgate and the harness hangs out of the SUV, I was looking for something like the factory hitch what has a harness the routes thru a hole in the floor to the hitch
asked by: Michael
Expert Reply:
The Curt hitch # 13354 and the Draw-Tite part # 75614 do not require trimming of the rear bumper, but they do require the trimming of the heat shield.
The recommended trailer wiring is part # 118424 and the recommended installation method is to have it come out of the rear hatch and have the door shut on the wires when needed. If you wanted to route it through a hole in the trunk floor board that may be possible, but we have never tested this method so we don't know for certain if that is possible.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included to the right that explains how to measure to choose a ball mount to tow the trailer level.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Trailer Hitch for 2011 Acura MDX that Allows Full Sized Spare to be Kept
- Q&A: Comparing Thule AeroBlade Crossbars vs WingBar Evo Crossbars
- Q&A: Can Rhino Rack Hanging Rack Carry a Trek Verve 3
- Q&A: Trailer Hitch Fit for 2022 Kia Niro PHEV Plug In Hybrid
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Does Curt Trailer Wiring Harness part # C55567 Fit 2014 Mazda 3 Hatchback
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: Hitch Rattles Against Exhaust of 2019 GMC Terrain
- Q&A: Vehicle Squeaks After Trailer Hitch Install
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose a Battery Charger
- Article: Trailer Hitch Installation Tips
- Article: How to Choose the Right Trailer Hitch Class