Hitch Recommendation for a 1985 Chevy C10 with 6 foot Bed
Question:
Do you sell a receiver hitch to fit a 1985 chevy c10 stepside?
asked by: Mike
Helpful Expert Reply:
Yes, check out the Draw Tite hitch part # 75034. This has been confirmed to fit your 1985 C10 with a 6 foot bed and step side. Since you have a 6 foot bed you will also need the spacer block part # 01077-011.
For trailer wiring you would want part # 18252.
For ball mounts I recommend the etrailer Ball Mount Kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag.
Products Referenced in This Question
4-Way Flat Trailer Connector w/ 72" Harness, Circuit Tester and Wire Taps
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- 6 Feet Long
- Universal Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 8000 lbs WD GTW
- 2 Inch Hitch
- 800 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Search Results: 41504
- Search Results: tow hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Article: Tips on How To Tow a Trailer
- Search Results: 44649
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Video: Choosing the Right Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: 68149
- Search Results: 25580
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Article: Trailer Wiring Diagrams
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Choosing the Right Brake Controller
- Shop: Brake Controller
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Fifth Wheel Hitch
- Article: My Trailer Hitch Doesn't Fit
- Search Results: led turn signal
- Search Results: dust cap
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires