Fit of Draw-Tite Class III Hitch # 75758 on 2014 Ford Escape S Model
Question:
Hello, will the Draw-Tite hitch 75758 fit my 2014 ford escape S? After watching the install video the attachment points look the same and I doubt there would be any interference with the rear fascia or the exhaust. Thanks.
asked by: R. K
Expert Reply:
The Draw-Tite # 75758 Class III hitch is a fit for all models of the 2014 Draw-Tite, according to my contact at Draw-Tite.
If you'll be using the hitch for towing purposes, you'll also need the following to complete your towing system:
Trailer wiring harness # 118566
Ballmount, # AMSC2
2 inch trailer ball, # 63845 or 1-7/8 inch trailer ball, # 19260
Locking hitch pin, part # e98882
I've linked you to some install videos that you might find helpful.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Matte Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Shock Absorbing
- Convert-A-Ball
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Stainless Steel
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-E-Loader Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: 2005 Nissan Titan Trailer Running Lights Not Working
- Q&A: Which Trailer Hitch Fits on a Ford E-350 Van
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: My Trailer Hitch Doesn't Fit
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Q&A: How to Activate Trailer Lights on 2014 Jeep Grand Cherokee Laredo with C55515 Wiring Harness
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Q&A: How to Pick Out Replacement Hub for UFP Hub Marked H-1377 A4E
- Q&A: Solution for Needing Replacement Atwood Master Cylinder for Surge Actuator
- Q&A: Replacement for Atwood 6,000 lb Hydraulic Actuating Coupler for Drum Brakes
- Article: Roadmaster Vehicle Specific Base Plates
- Article: Tips on How To Tow a Trailer