Installing Brake Controller on 2011 Ford Expediton with OEM 4-Pole Connector
Question:
I have a 2011 ford expedition 4x4 EL. I would like to install a brake controller and 7 pin connector for pulling a travel trailer. I did find the connector under the dash for the brake controller which should be easy to install. I currently have a factory 4 pin connector. There is also is an extra blue wire that is stubbed off which I am assuming is for the brake controller. Do I need to run a 12 volt wire and a reverse light wire to the battery or are the wires already wired to the rear of the vehicle? What is the easiest cleanest way to convert this to a 4pin and 7 pin?
asked by: Brett S
Expert Reply:
I'd recommend using a # 37185 4-pole to 7-way adapter. The adapter would plug into your existing 4-pole, and would have 4 wires remaining. The blue wire on the adapter would connect to the blue wire you found on the frame rail. If there is a stubbed off black, orange or red wire along with the blue wire, it would carry the 12-volt accessory power circuit, and would attach to the black wire on the adapter. If there is no wire, you'd need to run your own 12-volt circuit to the positive battery terminal using a length of 10 gauge wire like part # 10-1-1 and an inline circuit breaker like part # 9510.
The purple wire on the adapter usually carries the reverse light circuit. If you need it, it can be tapped into the reverse light circuit of the truck, otherwise it can be bundled up out of the way. The white adapter wire is grounded to the truck frame.
If you don't already have one, I'd recommend a proportional controller like the Prodigy P2, part # 90885. A proportional controller has an internal accelerometer that can sense how quickly the tow vehicle is coming to a stop. It would then send the proper amount of voltage to the trailer brakes so the trailer and tow vehicle stop at the same rate. The P3, pare # 90195 operates much like the P2, but I find it to be a bit more user-friendly, especially the diagnostics. If there's a problem with the braking system, the P3 will spell out the problem in plain English, while the P2 will display an error code that you'll most likely need to look up. For a Tekonsha controller, you'd also need the # 3035-P wiring adapter.
Products Referenced in This Question
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
40 Amp In-Line Circuit Breaker - Perpendicular Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Q&A: Brake Controller Recommendation for a Truck with Air Brakes and a Trailer with Electric Brakes
- Article: Most Popular Wheel Bearings
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Parts Needed To Install A Brake Controller On A 2023 Freightliner Cascadia
- Q&A: Parts Needed to Install 7-Way/4-Way on 2024 Kia Telluride with LED Taillights
- Q&A: How do I Tell if the Brake Controller is Bad
- Q&A: Lift Kit Options For A 2015 Winnebago Micro Minnie 1706FB