Which Reese Weight Distribution Lift Brackets for 2-1/2-Inch Wide Trailer Frame

Question

Question:

Are their different size lift brackets I should be considering? My trailer frame is only two plus inches wide and there is substantial space left with the lift bracket I recently purchased with the reese dual cam

asked by: Leonard T

0

Expert Reply:

The Reese Replacement Lift Bracket for Reese Weight Distribution Systems that you referenced, part # RP21501, is a suitable choice for use on your trailer frame that is roughly 2-1/2-inches wide.

expert reply by: Adam R

0

Answer 1

Replacement Lift Brackets with Handle for Reese Weight Distribution Systems #RP6637 that you were looking at is a kit that includes 2 of the Replacement Lift Bracket for Reese Weight Distribution Systems #RP21501. This is the current bracket offered…

view full answer...

Answer 2

The Reese Snap-Up Handle for Reese Weight Distribution Lift Brackets #RP58162 measures 18-inches overall length, has an outer diameter (O.D.) of 1-inch and an inner diameter (I.D.) of 13/16-inch. This is used to operate weight distribution lift…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Which Reese Weight Distribution Lift Brackets for 2-1/2-Inch Wide Trailer Frame

Product Page this Question was Asked From

Continue Researching