Installing a Brake Controller on a 2014 Thor Palazzo on a Freightliner XCS Chassis
Question:
Do you sell a cable that connects a Prodigy P2 Brake controller to a Freightliner XCS chassis brake port? I have a 2014 Thor Palazzo and need to install the brake controller that I removed from my previous RV. Thanks for your assistance. Regards
asked by: David C
Expert Reply:
I do not have a plug-in style brake controller harness that was designed for a Freightliner XCS chassis brake port, but I do have a hard wire kit that will allow you to complete the installation of a brake controller. I spoke with Thor Motor Coach, and he said Freightliner will put a brake port on their chassis, but they are not aware of a harness that will fit.
There are 4 wires on a brake controller that need to be connected. Since your RV has a brake controller port, you may be able to splice into the wires coming from that port. On the brake controller the black wire is for 12-volt power, the white wire is ground, the blue wire is electric brake output power from the brake controller and the red wire is for the stop light switch.
I do not have a wiring diagram for your RV, so I do not have information on wire colors or functions on the Freightliner brake port, but you can test the wires to see if they can be used. One wire should have constant 12-volt power, this will connect to the black wire. One wire should only have power when the brake pedal is pressed, and this will connect to the red wire. One wire is ground, and one wire should run back to the 7-way trailer connector for the blue wire.
If the wires do not function appropriately or are not accessible, then you can hard wire the brake controller the traditional way using our brake controller wiring kit, # 5506. The black and white wires will run to the positive and negative posts of a 12-volt battery on the motor home. The blue wire will run to the electric brake output circuit on the 7-way trailer connector. You may need an additional length 10-gauge wire, like part # 10-1-1, since it will need to run the length of the motor home. Finally, the red wire will tap into the stop light circuit. This is typically found at the stop light switch on the brake pedal arm. There will be several wires coming out of the stop light switch, but you will want to splice into the wire that only has power when the brake pedal is pressed. I recommend using a circuit tester, like part # PTW2993, to test for the correct wire before splicing.
Products Referenced in This Question
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Redarc Tow-Pro Elite Brake Controller for Tekonsha Harness - 2 Modes - 1 to 3 Axles - Proportional
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Article: Most Popular Wheel Bearings
- Q&A: Brake Controller Recommendation for a Truck with Air Brakes and a Trailer with Electric Brakes
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Parts Needed to Install 7-Way/4-Way on 2024 Kia Telluride with LED Taillights
- Q&A: How do I Tell if the Brake Controller is Bad
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Q&A: How Is Spring Bar Tension Set Up with Trailer Weight Distribution System