Trailer Hitch Receiver Options For A 1999 Saab 9-3
Question:
Hi, Looking for a trailer hitch for a 1999 Saab 93 to fit on a hatchback. If you dont have one is there a chance you would have a schematic or place I could get a copy. I will have a custom one made if we can determine the configuration / points to install etc. Thank you, Bruce
asked by: Bruce M
Expert Reply:
Hey Bruce,
We unfortunately do not offer a custom fit hitch for a 1999 SAAB 9-3. You would have to go with a weld-on hitch and figure out the correct drop to clear the rear fascia. We don't have any schematics for this so I recommend reaching out to a local fabrication/welding company to determine the best fit/mounting points. We offer the following weld-on hitches:
Draw-Tite
7" Drop # 41990-07
Curt
3" Drop # 15901
9" Drop # C47CR
10.865" Drop # 15902
11-1/2" Drop # 15903
Products Referenced in This Question
Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 1500 lbs TW
- 15000 lbs GTW
- Class V
- 2 Inch Hitch
- 3 Inch Drop
- CURT
more information >
Curt Class V Universal Weld-on Receiver Hitch and Brackets with 10.865" Drop
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 1200 lbs TW
- 12000 lbs GTW
- Class V
- 2 Inch Hitch
- CURT
more information >
Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 60" Wide
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 60 Inch Wide
- 1500 lbs TW
- 15000 lbs GTW
- Class V
- 2 Inch Hitch
- 11-1/2 Inch Drop
- CURT
more information >
Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2"
- Heavy Duty Receiver Hitch
- Weld-On
- 44 Inch Wide
- 1600 lbs TW
- 16000 lbs GTW
- Class V
- 2 Inch Hitch
- 7 Inch Drop
- Draw-Tite
more information >
Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 1600 lbs TW
- 16000 lbs GTW
- Class V
- 2 Inch Hitch
- 9 Inch Drop
- CURT
more information >
Product Page this Question was Asked From
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Concealed Cross Tube
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Q&A: How Does a Hitch Being Installed Effect the Automatic Braking on a 2021 Nissan Rogue?
- Q&A: Recommended Hitch for a 2024 Nissan Altima
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Is There a Trailer Hitch & Wiring For 2024 Chevy Trax
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Article: Rooftop Cargo Carriers
- Article: How to carry Bikes on a Vehicle
- Article: How to Measure for Trailer Hitch Drop
- Q&A: How To Carry a Pedego Tandem E-Bike With a 2019 Lincoln MKC
- Q&A: Replacement Grease Seal 225255UC for 2015 Wesco Trailer