Replacement Dual Water Inlet For A 2005 Exiss 414 Horse Trailer
Question:
Do you have a 2005 exiss 414, city water connector , fill water , combo. Thanks.
asked by: Lagina B
Expert Reply:
Hey Lagina,
We offer a few different dual water inlets so you'll want to measure the cutout hole and overall dimensions to make sure that the replacement will be a fit and not interfere with any other trim or accessory that could be mounted on the wall of the trailer next to it.
The Valterra Lockable Dual RV Water Inlets # A01-2000VP (white) and # A01-2000BKVP (black) are a pretty standard size for most trailers so I'd say these are likely going to be what you need. They measure 7-5/8" wide x 6-1/2" tall overall and require a 5-7/8" wide x 4-3/4" tall cutout hole. They also come with a locking door which is pretty standard on horse trailers. If you find that yours differs in size and these two options won't fit then let me know and I'd be happy to look for one that would.
For the installation you'll want to use some butyl tape # AL28FJ on the back side of the mounting flange and run a bead of non-sag sealant # 344270341437-1 around the outer edge of the flange for a watertight seal.
Products Referenced in This Question
LaSalle Bristol XTRM Universal Non-Sag Sealant for RVs - White - 10.1 oz - Qty 1
- RV Roof Repair
- Sealant
- 10.1 oz
- Non-Sag
- Self-Leveling
- White
- LaSalle Bristol
more information >
Valterra Lockable Dual RV Water Inlets - City Water and Gravity Fill - Brass Valve
- RV Water Inlets
- City Fill Inlet
- Gravity Fill Inlet
- Surface Mount
- 5-7/8 Inch Diameter Cutout
- 1/2 Inch Deep
- Plastic
- 7-5/8 Inch Diameter Flange
- Brass
- Black
- Valterra
more information >
Valterra Lockable Dual RV Water Inlets - City Water and Gravity Fill - Brass Valve
- RV Water Inlets
- City Fill Inlet
- Gravity Fill Inlet
- Surface Mount
- 5-7/8 Inch Diameter Cutout
- 1/2 Inch Deep
- Plastic
- 7-5/8 Inch Diameter Flange
- Brass
- White
- Valterra
more information >
Alpha Systems Butyl Tape for RV Weatherproofing - 20' x 1" x 3/16"
- RV Roof Repair
- Tape
- Butyl Tape
- 20 Feet Long
- Colors May Vary
- Alpha Systems
more information >
Product Page this Question was Asked From
Valterra RV Gravity Fill Water Inlet
- RV Water Inlets
- Gravity Fill Inlet
- Surface Mount
- 3-1/2 Inch Diameter Cutout
- 1/2 Inch Deep
- Plastic
- 4-1/2 Inch Diameter Flange
- Plastic
- Black
- Valterra
more information >
Continue Researching
- Q&A: Distance Between Mounting Holes of JR Products Standard Cable Hatch
- Q&A: Replacement Lid for MaxxFan and MaxxFan Plus Roof Vent 4951KS
- Q&A: Recommended Replacement For An Atwood GCA10A-4E RV Water Heater
- Article: Top 10 Upgrades for Your Camper
- Q&A: Replacement Panel for Powertek PDC1001
- Article: How to Raise Your Travel Trailer Height
- Q&A: Replacement Converter for Parallax/Magnetek Models 7355, 7155, and 8355
- Q&A: How to Wire Solera Smart Arm 12V Power RV Awning
- Q&A: What do the Hub Face and Spring Center Measurements Mean for an Axle
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: How Your RV Water System Works: A Complete Newbie's Guide
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Article: Trailer Wiring Diagrams
- Article: Stability Control for Heavy Duty Vehicles