Will Biker Bar Fit Suzuki Boulevard M109R

Question

Question:

Hi Do thé biker bar work with a Suzuki Boulevard m109r ?

asked by: Sylvain H

0

Expert Reply:

B&W hasn't had a chance to test the Suzuki Boulevard M109R but it may fit the # BWMC2304. To find out if it will fit you will have to take some measurements. A two piece motorcycle tube frame is needed for the Biker Bar to clamp onto. The diameter of each frame tube must be at least 1.125" and no more than 1.5".

Check that there is nothing hanging down below the tube frame, such as a motor, transmission or exhaust. With the rider sitting on the motorcycle, the distance from the side of the frame tubes to the ground must measure between 5" and 6.5".

The distance form the outside edges of each frame tube must be no less than 10" and not more than 14.5". Take this measurement where the Biker Bar will be attached. There must be 1/2" of clearance between the motor, transmission, and primary drive to allow clearance for the Biker Bar clamps.

expert reply by: Robin H

0

Biker Bar Measurements.
(click to enlarge)

Answer 1

I spoke with a coworker of mine who is a Harley aficionado and he said your bike is build basically on a shorter version of the Touring frame so you need the part #BWMC2301.

view full answer...

Answer 2

To install the Small Coin Pattern Vinyl Flooring #TS97FR with the RV Flooring Adhesive #TS76FR you just need to make sure that your trailer floor is a bare wood so you have the best bonding of the adhesive as possible. Be sure to sweep it out really…

view full answer...

Answer 3

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 4

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Answer 5

First of all that's a pretty sweet looking bike! Secondly, while there are no B&W Biker Bar systems specifically designed for your Indian Chieftain, you still might be able to utilize the Tie-Down System #BWMC2301. I've attached a photo…

view full answer...

Answer 6

According to the 2017 Jeep Wrangler owner's manual, your Sport model has different max weight capacities depending on the Jeep's axle ratio. For a 3.21 axle ratio, your maximum tongue weight is 200 lbs and maximum gross trailer weight is…

view full answer...

Answer 7

I would be happy to help you set your 2022 Jeep Gladiator for flat towing. You're going to need a base plate kit, a tow bar, tow bar wiring, supplemental braking system, protective screen, charge line, stop light switch, and a high/low adapter. I…

view full answer...

Answer 8

The only thing I can think of that could cause an issue like this is that you have indicator light wired incorrectly to something that has power when not connected to the motorhome. In the typical setup you would connect the power for the indicator…

view full answer...

Answer 9

The Replacement Bar for B&W Biker Bar Motorcycle Tie-Down System #BWMC2302B is the replacement bar that fits H-D Dyna, Softail, and V-Rod bike frames. The #BWMC2301B is the Replacement Clamping Bar for B&W Biker Bar Motorcycle Tie-Down for…

view full answer...

Answer 10

The B&W biker bars are only confirmed to fit certain Harley Davidson bikes so the only fit I can confirm for you is for your Dyna, the B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Softail, Dyna, V-Rod #BWMC2302. The…

view full answer...

Will Biker Bar Fit Suzuki Boulevard M109R

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching