Replacement Brake Kit, Surge Actuator, and Bearing Kit for a 1988 EZ Loader Boat Trailer
Question:
I am looking at replacement brake drums for a 1988 EZ Loader boat trailer equipped with drum surge brakes but dont know if the axle cabacity is 3500 lbs or 3750 lbs. Reviewing your videos, it appears the 3750 has riveted brake pads. Can I put the 3750 lbs kit on a 3500lb axle? Also, I will be replacing the master cylinder. The unit removed is a Atwood 85736. Are these still made or do I need to replace the entire unit? Finally, how do I determine what replacement bearing kit to purchase? It is a 10inch drum with 5 studs. Thank you!
asked by: Scott M
Helpful Expert Reply:
Hey Scott!
Both the 3,500 lb and 3,750 lb brake assemblies work with a 10" x 2-1/4" drum so either one will fit with your hubs, but you can verify your axle capacity either on the sticker tag on the side of your EZ Loader Trailer, or by looking at the tag in the middle of your axle(s).
One you know what weight capacity you have then I recommend getting Free-Backing brakes so you'll be able to back the trailer up. For 3,500 lb brake assemblies this will be part # AKFBBRK-35 and for 3,750 lb brake assemblies it will be part # T4071600-500.
Atwood went out of the coupler business a number of years ago so there aren't any direct replacement master cylinders. To replace your surge brake actuator you can use either the bolt-on # DM72VR or a weld-on for an A-Frame # DM8609502.
Finally, for a replacement bearing kit you should need the kit # BK2-100 for a #84 spindle. You can verify this kit will fit your application by comparing the parts you remove with the following:
- Inner Bearing L68149
- Outer Bearing L44649
- Grease Seal ID 1.719" and OD 2.565"
Products Referenced in This Question
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Straight Tongue Coupler
- Bolt-On
- 7000 lbs GTW
- 2 Inch Ball Coupler
- Drum Brakes
- No Lockout
- Demco
more information >
Demco Hydraulic Brake Actuator - Drum - Primed - A-Frame - 2" Ball - 8,000 lbs
- Brake Actuator
- Surge Brake Actuator
- A-Frame Coupler
- Weld-On
- 8000 lbs GTW
- 2 Inch Ball Coupler
- Drum Brakes
- No Lockout
- Demco
more information >
Dexter Hydraulic Brake Kit - Free Backing - 10" - Left and Right Hand Assemblies - 3,750 lbs
- Trailer Brakes
- Hydraulic Drum Brakes
- Standard Grade
- Free Backing
- Manual Adjust
- Single Servo
- 10 x 2-1/4 Inch Drum
- 3750 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Product Page this Question was Asked From
Hydraulic Trailer Brake Kit - Uni-Servo - Free Backing - 10" - Left/Right Hand - 3,500 lbs
- Trailer Brakes
- Hydraulic Drum Brakes
- Standard Grade
- Free Backing
- Manual Adjust
- Single Servo
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Q&A: Free-Backing Hydraulic Brake Assemblies for Trailer with 3500 lb Axles
- Q&A: Correct Replacement for Tru-Ryde Hub/Drum RVD-H-545
- Q&A: Demco vs. etrailer Hydraulic Dacromet 3,500 lb Trailer Brakes
- Article: How to Bleed Your Trailer Surge Brakes
- Q&A: Determining Which Brakes Fit 10" x 2-1/2" Drums On Boat Trailer
- Q&A: Replacement Hub and Drum Assembly for Tru-Ryde RVD-H-545
- Q&A: Replacement Hub & Drum For UFP HD-1377-10 & Hydraulic Brakes For Boat Trailer
- Q&A: Replacement Dexter Hydraulic Brake Assemblies for 023-344-00 and 023-345-00
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Tire Sizing
- Article: Most Popular Wheel Bearings
- Article: Trailer Wiring Diagrams
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision