Will the Curt Euro Style Ball Mount Work With a Class I Receiver
Question:
i am trying to a ball mount, euro style, for my Lexus GS430 2006y with C11372 Class I Hitch. By my measurements I require c45561 or c45571. No where on any sites have I found any reference to internal dimensions from the hole for pin to where bend starts. A profile shot on a one inch square paper or wood board would be nice. HELP.
asked by: Daniel
Expert Reply:
Well Daniel I hate to be the bearer of bad news, but you're actually not going to be able to use any of those Euro style ball mounts with your Curt Trailer Hitch Receiver # C11372. This is a class I hitch and the drawbar(s) you're looking at are for class II hitches which may have the same receiver openings, but they can not be used together - the ball mount will not fit all the way because there is a built in tab/stopper to prevent you from doing this.
It looks like all that's offered for your Lexus are class I hitches so you'd need to use a different drawbar like the Draw-Tite Drawbar for 1-1/4" Hitches # 3594 with the hitch ball # 19260 which would essentially recreate what you're looking for.
The only thing you'd need to do is measure your rise and drop following the guide I've attached and pick a drawbar based off of your needs.
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Product Page this Question was Asked From
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 3-1/8" Rise - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- One Ball
- Steel Ball
- Steel Shank - Gloss Black
- Rise - 3 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Trailer Tire Sizing
- Article: Steel vs. Aluminum Ball Mounts
- Article: How to Measure for Trailer Hitch Drop
- Q&A: How Do I Know How High The Ball Should Sit Above the Ground
- Article: Trailer Wiring Diagrams
- Article: My Trailer Hitch Doesn't Fit
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Can a 1-7/8 inch Hitch Ball be Used with a 2 inch Coupler on Trailer
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Q&A: Adding Manual Lockout to Surge Brake Actuator
- Q&A: What is the Difference Between Class 1 and Class 2 Hitches for the Scion XB
- Q&A: How to Upgrade Trailer with 45 MPH Speed Rating for Highway Speeds
- Q&A: Recommended Roof Rack Bike Carrier for Wider Bike Tires
- Q&A: What Hitch Gives the Highest Ground Clearance on My 2022 Toyota Sienna?