Carlisle Electric Over Hydraulic Actuator Recommendation for Converting a Trailer With Surge Brakes
Question:
i have a 1972 ideal car trailer with surge brakes. i want to put elec brakes on but drums wont work with elec brakes. so i need a hub and drum to fit my spindel. outer bearing #LM44649 outer bearing is 1.0635 inside,1.98 outside,and.5610 wide.The LM48548 inner is 1.375 inside,2.5625 out side, and 0.71 wide. I would like to know if you have hub and drum to fit this spindal or should i get a new axle,or have any suggestions for me thanks.
asked by: Charley S
Expert Reply:
I have a solution for you that you maybe didn't think of, but I checked the bearing numbers you gave and could not find any replacement hubs that match with both of those bearings.
I would recommend you convert your trailer to electric-over-hydraulic brakes. Basically you will replace your surge actuator with an electric over hydraulic actuator and a hydraulic pump that is controlled by a brake controller will apply the hydraulic brakes of your trailer. EOH braking systems are literally the best of both worlds. You get the flexibility of electric brakes and the power of hydraulic.
For an actuator to install on your trailer I would recommend the Carlisle Hydrastar Drum Actuator part # HBA-10. Of all the actuators we carry this one seems to work the best.
You will need a brake controller that is compatible with electric over hydraulic brakes, for that I would recommend the Prodigy P2 Brake Controller part # 90885. This is our top selling brake controller because of how easy it is to use and setup and how well it works.
I also attached an FAQ on adding electric over hydraulic brakes to a drum brake trailer for you to check out.
Products Referenced in This Question
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Hydrastar Electric Over Hydraulic Actuator for Drum Brakes - 1,000 psi
- Brake Actuator
- Electric-Hydraulic Brake Actuator
- 1000 psi
- Drum Brakes
- Hydrastar
more information >
Product Page this Question was Asked From
Replacement Trailer Hub Bearing - LM48548
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.375 Inch I.D.
- Bearing LM48548
- Race LM48510
- 2500 lbs Axle
- TruRyde
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Replacement Hub Options To Upgrade from 4 on 9.44 Inch Bolt Pattern
- Q&A: Converting From 4 On 9.44 to 5 On 5 Bolt Pattern
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Most Popular Wheel Bearings
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Q&A: Spare 15 Tire And Wheel With a 4 On 9.44 Bolt Pattern
- Q&A: Can a Trailer Axle be Converted to an EZ Lube Axle by Replacing Spindles
- Q&A: Replacement Hub/Drum Assembly Needed for a Dexter 8-147 Assembly
- Article: Trailer Tire Sizing
- Q&A: Replacement Bearings and Seal for Dexter Hub 8-147
- Q&A: How to Find Out Which Replacement Wheel Bearings Needed for 1999 Bayliner Single Axle Boat Trailer
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: How to Tell the Weight Rating of a Trailer Axle