Can Trailer with Slipper Springs have Double Eye Springs attach to Same Hanger Channel
Question:
I have a single axle, rated at 2K, 4 x 8 ft foldable utility trailer with slipper springs. The hangers are welded to the trailer frame as one piece for bolt attachment of the single eye and slipper see uploaded picture. I want to replace slippers with double eyes. Since the hangers are integral with the frame and are at the same level/height can I buy shackles shortest length possible to add to the OEM hanger so I can use the double eyes? Do I need a shackle for the front and rear eye to keep the trailer/leaf spring level? Im thinking if I installed 2 inch shackles this will raise my trailer height 2 inches. If I installed the shackles would there be any concerns I should have?
asked by: Walter
Expert Reply:
You have a really interesting suspension setup on your trailer. I don't know what the width of the channel is that your springs attach to but to go to a double leaf will require using a hanger kit like the part # APS4 that you referenced. If you were to add shackles to the rear hanger area the spring would be unlevel and you can't add them to the front as well. Plus you have to factor in that you most likely would not have room for two shackles and springs in the channel currently.
So what I would recommend doing is having a weld on hanger kit like the part # APS4 welded to your frame so that you can use a double eye spring. Or you could stick with slipper springs and keep the setup as-is.
Product Page this Question was Asked From
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
- Trailer Leaf Spring Suspension
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Single Axle
- etrailer
more information >
Continue Researching
- Shop: Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
- Shop: 3-Leaf Double-Eye Spring for 2,000-lb Trailer Axles - 23-1/2" Long
- Shop: 4-Leaf Double-Eye Spring for 2,000-lb Trailer Axles - 26" Long
- Video: Review of CE Smith Trailer Leaf Spring Suspension - CE14026G
- Search Results: leaf spring suspension
- Search Results: 26 inch leaf springs
- Search Results: trailer springs
- Shop: CE Smith Front/Center/Rear Hanger Bracket for Double-Eye Springs - Galvanized Steel - Bolt On
- Shop: CE Smith Front/Rear Hanger Bracket for Double-Eye Springs - Galvanized Steel - Bolt On
- Search Results: mirrors
- Shop: etrailer Rust-Resistant 3-Leaf Double Eye Spring for 2K Trailer Axles - 20-3/8" Long - Dacromet
- Shop: U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4-1/4" Long U-Bolts
- Search Results: trailer leaf springs
- Video: Universal Group Trailer Suspension - Leaf Spring Suspension - SP-113275 Review
- Search Results: utility trailer axle
- Video: Review of CE Smith - Trailer Leaf Spring Suspension - CE14035G40
- Video: etrailer Trailer Suspension - Leaf Spring Suspension - APS4 Review
- Video: Review of Dutton-Lainson Replacement Miter Gear Kit Jacks 1250 To 2000 LBS After 1996 - DL22439
- Video: Review of Dexter Trailer Leaf Spring Suspension - Suspension Kits - K71-403-00
- Shop: Floor Mats
- Shop: Towing Mirrors
- Shop: Vehicle Seat Covers
- Shop: Windshield Wiper Blades
- Q&A: Why Can't Trailer Axles Just be Flipped
- Video: Lock N Roll Straight Tongue Trailer Coupler - Off Road Coupler - 336TS506 Review
- Q&A: Replacement Gear Kit DL22439 For Dutton-Lainson Boat Jack
- Q&A: Replacement Cap for etrailer Swivel Jack
- Q&A: What is the Diameter of the Replacement Trailer Jack Cap # MJ-1500B-CP
- Q&A: Do Spring Seats Have to Be Welded to Install Axle Over Under Kit
- Q&A: How to Lift a Single Axle Trailer w/ an Axle Flip Kit