Parts Needed to Make Rhino-Rack Legs Fit Pace Edwards UltraGroove

Question

Question:

I am looking for the T-slot nuts for the Pace Edwards ultra groove tonneau cover. to mount my Rhino-Rack RLT600 leg kits

asked by: Ray S

0

Expert Reply:

What you need is the Adapter Kit for Rhino-Rack RTL600 Legs # RRT-FK1. These are designed for Thule tracks but we have found that they will also allow you to use Rhino-Rack Legs # RRRLT600 with the UltraGroove # 311-KRD7833 on your 2023 Ram 2500.

expert reply by: Robin H

0

Answer 1

Yes, the Rhino-Rack Vortex Crossbars #RRVA180B-RRRLT600 will fit the Pace Edwards UltraGroove #311-KRC3250 on your 2022 Ram 2500. This will also require the Adapter Kit for Rhino-Rack RTL600 Legs #RRT-FK1. Once installed, you will be able to add a…

view full answer...

Answer 2

Rhino Rack actually has a kit designed specifically for fitting the tracks of a RetraxPro XR ladder rack with the part number #RRVA180B-RRRLT600. This kit includes the feet you mentioned #RRRLT600 which fits the tonneau.

view full answer...

Answer 3

The t-slot in your Pace Edwards Explorer Rails measure 0.759" wide so you can use the Eye Bolt Kit for Inno Roof Deck Platform Rack #IN37FR to add in more tie down points. The eye bolt will simply screw into the t-slot hardware for a fast and…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 7

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The 71" Rhino-Rack Vortex Crossbars for Retrax XR Tonneau Covers item #RRVA180B-RRRLT600 are the correct set for your 2022 Ram 3500. These are made for full size trucks and fit in the rails of the Retrax PRO XR. These crossbars are exactly…

view full answer...

Answer 12

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Parts Needed to Make Rhino-Rack Legs Fit Pace Edwards UltraGroove

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching