Weight of Curt PowerRide 5th Wheel Trailer Hitch for RAM Puck System Prep Package

Question

Question:

How much does the Curt PowerRide 5th Wheel Trailer Hitch for RAM weigh? It can be taken apart?

asked by: Benny

0

Expert Reply:

Yes, you can take apart the 30,000 lb Curt PowerRide 5th Wheel Trailer Hitch for RAM Towing Prep Package # C74BR.

The total weight of the # C74BR is 196 lbs, with 89 lbs being the base and 107 lbs being the head unit.

expert reply by: Kyle S

0

Answer 1

The 5th wheel hitch that has the most capacity and fits your 2024 Ram 3500 is from Demco; it has a 31,000 lb capacity and is the following part number: - Demco UMS Double Pivot 5th Wheel Hitch - Ram Prep Package #DM67GV That 31,000 lb capacity is…

view full answer...

Answer 2

For a cab and chassis style Ram 3500 you would need to have a qualified welder install a Turnoverball hitch #BWGNRK1500 and then could use a Companion #BWRVK3500. This hitch is only rated up to 20,000lbs so if you were looking to tow more we would…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Weight of Curt PowerRide 5th Wheel Trailer Hitch for RAM Puck System Prep Package

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching