Hub with 5 on 4-1/2 inch Bolt Pattern that Fits Truryde 2,500 lb Axle Spindle

Question

Question:

do you have a hub assemble in 5x4 1/2 or 4on that will fit this spindle thanks

asked by: Duane C

0

Expert Reply:

Yes, the Dexter hub part # 8-258-50UC1-EZ has a 5 on 4-1/2 inch bolt pattern and fits the spindle part # TRU27FR.

expert reply by: Jameson C

0

Answer 1

Measure the inside diameter and depth of your brake drums. You need to pull the drums off to do it. The brake assemblies you looked at, part #AKEBRK-35, fit drums that are 10 inches in diameter and 2-1/4 inches deep. Let me know what yours measure…

view full answer...

Answer 2

The spindle part #TRU27FR would require a hub designed to fit BTR spindles like the part #AKIHUB-545-2-2K. Then you could use up to a 12 inch diameter wheel and tire combo with a 5 on 4-1/2 inch bolt pattern like the Kenda 5.30-12 Bias Trailer Tire…

view full answer...

Answer 3

Yes, the 2 Trailer Idler Hub Assemblies #TA88545-2 will fit on 2 of the BTR E-Z Lube Spindles #TRU27FR. The hubs include the correct Bearings #L44649, Races #L44610, Seals #RG06-020 and Grease Caps #RG04-040 for the spindle.

view full answer...

Answer 4

The Lippert Lubed Straight Spindle with Brake Flange #TRU27FR has a stub diameter of 1-5/16" and is designed to fit a 2,500-lb axle. If your tow dolly has those specifications, this spindle will work on your axle. If you're not sure,…

view full answer...

Answer 5

Looks like you found the chart that Jeff D made that shows common axle capacities based on diameter: Typical Axle Diameters Based on Axle Capacity - 1,000-lb - 2,000-lb Axles: 1-1/2 inch - 1-3/4 inch diameter - 3,500-lb Axles: 2-3/8 inch diameter -…

view full answer...

Answer 6

The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn. If the spindle uses a castle nut and cotter pin or tang nut, tighten the nut finger tight until…

view full answer...

Answer 7

It looks like you might be asking about a few different torque specs so I'll address all of them separately. For a trailer axle spindle nut like part #165686 you will need to run the spindle nut down until there is no more side-to-side play…

view full answer...

Answer 8

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub…

view full answer...

Answer 9

The TruRyde Spindle Nut #165686 has an outer measurement of 1.45 inches. You will use a 1-1/2 inch socket on this castle nut or we usually use a channel lock for these installations. I've attached a video of an installation of a hub to…

view full answer...

Answer 10

According to our installers you will tighten the trailer spindle nut until it stops by itself. In other words do not torque it down as hard as you can. It just has to be tight. A little play is to be expected. You do not want to torque it down too…

view full answer...

Answer 11

There is not a torque spec on the axle nut for the Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 #84545BX. The axle will have a castle nut that should be tightened until there is no side to side play and then backed off to the…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Hub with 5 on 4-1/2 inch Bolt Pattern that Fits Truryde 2,500 lb Axle Spindle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching