Replacement Bearings, Races and Grease Seal For a 2017 Karavan KB2200 Boat Trailer

Question

Question:

I have a 2017 Karavan KB2200 boat trailer VIN 5KTBS2414HFXXXXXX. Do you sell replacement wheel bearing kits? Do I have to buy the whole hub or can I just get bearings/races/seals etc? My trailer has the Sure Lube type grease system. Thank you

asked by: Ann C

0

Expert Reply:

For your 2017 Karavan KB2200 boat trailer you will need the following parts for rebuilding your hubs.

Inner Bearing # L68149
Outer Bearing # L44649
Inner Race # L68111
Outer Race # L44610
Grease Seal # TMK29ZR
Cotter Pin # 165649

If the Sure Lube cap is damaged during removal you can replace them with the superior Bearing Buddy Bearing Protectors # BB1980A-SS.

expert reply by: Bud M

0

Answer 1

We have Bearing Buddy Bearing Protectors that are the 2.240 inch you referenced but they are not threaded. They are part #BB2240SS for stainless or #BB2240 for chrome plated. If you don't want to replace your hubs to utilize those, then the best…

view full answer...

Answer 2

The etrailer Trailer Axle Beam #e23GR will use the common bearing sizes for a 6,000lb axle with #42 Spindle. Inner Bearing #25580 Inner Race #25520 Outer Bearing #15123 Outer Race #15245 Grease Seal #GS-2250DL Grease Cap #DC250L-DCRP This axle would…

view full answer...

Answer 3

Pulling the wheels and hubs off of your 5th wheel trailer is the best option when trying to identify what wheel bearings and seals are installed. On the back of the wheel bearings there usually is printed a part number like #L44643. With these…

view full answer...

Answer 4

For each of your Lippert 3500lb axles you will need the following components. Timken Inner Bearing & Race #TMK73VR Qty 2 Timken Outer Bearing & Race #TMK23VR Qty 2 etrailer Grease Seal #58846 Qty 2 Grease Caps #RG04-040 Qty 1 We do not carry…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 9

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Replacement Bearings, Races and Grease Seal For a 2017 Karavan KB2200 Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching