Does Back End of Ford F-250 Need to be Raised to Install Timbren Suspension Enhancement TFR250SDJ

Question

Question:

Do you need a deep-well socket 15mm to remove the OEM bump stops on a 2020 Ford F250SD 4WD? Do you need to lift the rear-end of the truck 2020 Ford F250SD to install these? Note: I will be installing these while truck in sitting on flat concrete garage flooring.

asked by: Mark T

0

Expert Reply:

Yes, you will need a deep well 15mm socket, though you do not need to lift the back end of your 2020 Ford F-250 to install the Timbren Suspension Enhancement System # TFR250SDJ.

expert reply by: Kyle S

0

Answer 1

We do - for your 2023 Ford F-350 you'll want the TorkLift StableLoad Suspension Upgrade w Quick-Disconnect #TL89CR.

view full answer...

Answer 2

Yes, the Timbren Suspension Enhancement System #TFR350SDJ that fits your 2022 Ford F-350 is compatible with the TorkLift StableLoad. The two install completely separately so there won't be any interference between the StableLoad and the…

view full answer...

Answer 3

If you find you need to trim the TorkLift StableLoad Suspension Upgrade for Upper Overload Springs #TLA7200 you have on your 2020 Ford F-350 I recommend using a reciprocating saw while lubricating it to keep from burning the rubber. We have found…

view full answer...

Answer 4

The Timbren Suspension Enhancement System #TFRTT350J would be my recommendation. These are designed to improve handling and safety by becoming more rigid with weight added. This will help increase stability, reduce the sag you mentioned, and each…

view full answer...

Answer 5

The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.

view full answer...

Answer 6

For a replacement you need the Titan Zinc-Plated Brake Actuator #T2477600. This is the Titan Model 10 which is the same as the Dexter DX12.5 you currently have on your boat trailer.

view full answer...

Answer 7

For your 2010 Forest River R-Pod 172 that has 3,500 lb Lippert torsion axles the correct lift kit is the #LC382741 that you referenced which will give you a 3-1/2 inch lift.

view full answer...

Answer 8

Hi there David; we do have truck camper jacks that can work for your F-250 with a lift and large tires. What you can use are camper jacks from Brophy, which have a 17" to 67" lift range, which is the highest possible lift height. There are…

view full answer...

Answer 9

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 10

I recommend replacing an entire ladder if it's damaged. You'll want to find a replacement based on the height. Such as the Stromberg Carlson #LA-401 that is 99-1/2 inches tall. They can be cut shorter to customize the length if needed.

view full answer...

Answer 11

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 12

For a 48" hitch extension that fits a 3" receiver you're going to want the TorkLift Cannon Hitch Extension item #TLE1648. This hitch extender is specially designed to work with Ford's 3" factory trailer hitch. This is the only…

view full answer...

Does Back End of Ford F-250 Need to be Raised to Install Timbren Suspension Enhancement TFR250SDJ

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching